Dehumidifier and air purifier in one device with 95% air purity Enjoy indoor air. This design dehumidifier makes that and more possible. Equipped with two technologies for the permanent improvement of air quality, the combination devices eliminate unhealthy moisture in residential and commercial spaces, offices, retail stores, unheated conservatories, basements, and garages. Furthermore, the indoor air is purified in the integrated filter, removing 95 percent of disease-causing bacteria and viruses, mold spores, pollen, house dust, fine dust, allergens, and other pollutants. A permanent health protection for all individuals in the room – a noticeable relief, especially for allergy sufferers and those with house dust allergies.  Everything for healthier indoor air and more quality of life A hygrostat-controlled dehumidification automation with target selection of the desired humidity (30% to 80%), digital air quality sensors, four operating modes including night mode, and a two-stage fan ensure reliable dehumidification and air purification. For unattended continuous operation, the device is equipped with overflow protection and also has a rear hose connection to permanently drain the condensate extracted from the air via a hose. Conveniently, the front color LED display shows the status of the indoor air quality in three colors (Blue, Green, Red). A lit segment display in the LED display provides precise percentage information about the current humidity, the preset target humidity, and the remaining operating hours with the activated 24-hour timer for time-controlled switching on or off.  Seeing indoor air with different eyes: Air quality sensors "You cannot tell from the air whether it is too humid or contaminated with pathogens. If mold spores or viruses are floating invisibly in the air, this usually only becomes noticeable when it is already too late." The sensor sees what you cannot see. It continuously measures the room air humidity. Convenient is the front-facing color LED display of the current room air humidity: Blue: Indicates a humidity level below 50%Green: Indicates an optimal humidity level between 50 to 70 %Red: Indicates a humidity level above 70% "Cleaned and dehumidified room air makes the difference" A person breathes in and out between 10,000 and 20,000 liters of air per day. If the air is too humid and contaminated with pollutant particles or pathogens, it burdens our immune system and, in the worst case, leads to respiratory diseases. Likewise, furniture, fixtures, and even the building structure can be damaged by consistently high humidity (> 60 percent).  Combined protection against moisture and pathogens With its combined air purification and dehumidification technology, this all-rounder reliably prevents the formation of unhealthy moisture nests and associated moisture problems such as mold growth, stains, and dampness. The room air is purified in a dual filter system consisting of a pre-filter and a high-performance filter, removing virus-laden aerosols, viruses (such as SARS-CoV-2 and influenza viruses), bacteria, mold spores, fine dust, house dust, pet hair, and other airborne pathogens. It also reduces the growth of dust mites and allergens. A clean solution. The high-performance filter is consumable and should be replaced from time to time. The pre-filter is washable and can be reused repeatedly.  Auto-Restart Function The auto-restart function (or memory function) allows the device to restart with the pre-selected setting after an unexpected shutdown due to a power interruption, as soon as the power supply is restored. This makes the dehumidifier suitable for use with a timer.  The complete solution for a healthy indoor climate This 2-in-1 device is characterized by extensive comfort features, high ease of use, and the pleasantly low noise level, making the air purifiers also suitable for use in noise-sensitive environments. Hygrostat-controlled dehumidification automation: In the hygrostat-controlled dehumidification automation, the device operates continuously until the desired air humidity level is reached. This can be set between 30% and 80% in 5% increments. After that, the compressor automatically switches off. If the target value is exceeded again, the device activates automatically. Thus, the dehumidifier always ensures optimal room air humidity according to your needs. Continuous operation: Condensed water on walls, glass surfaces, or cold bridges, combined with insufficient ventilation, are common causes of moisture damage, as well as when water from outside penetrates through a poorly insulated wall or during flooding and heavy rain events into the basement. To maintain a permanently dry environment, the air dryer features a powerful continuous operation. In this operating mode, the room air is continuously dehumidified at maximum performance. Night Mode: Poor air quality caused by excessive humidity, unpleasant odors, or stuffy air can literally rob you of sleep. In night mode, the device cleans and dehumidifies the air with a gentle airflow and a dimmed control panel. For a restful sleep to recharge. Clothes drying function: For gentle air drying of laundry, the drying mode is recommended. The clothes drying function (also known as the textile drying mode or SuperDry function) is comparable to traditional air drying outdoors. The air filter ensures that pollen and fine dust are not blown through the laundry and remain attached to it. 24-Hour Timer: This allows the operation to be turned on or off after a certain number of hours. In the bedroom, a combined air dehumidification and purification is recommended for a restful sleep – during the day, however, the device does not need to operate when one is out of the house. Similarly, dehumidification and air purification in the office or workplace are only necessary during working hours. For these and other usage scenarios, the device features a programmable 24-hour timer, which allows the operating time to be preset for automatic on or off switching in 1-hour increments. Thanks to the memory function, the operation can also be controlled with a standard timer switch if the device is to operate at the same times every day (for example, during off-peak hours).  air circulationIn this model, the compressor (= dehumidification) stops immediately upon reaching the desired humidity level, while the fan continues to run for a few more minutes to dry the interior of the device. Advantages at a Glance • Combined dehumidifier with high-performance air purifier (95% effective filtration of bacteria, viruses, pollen, fine dust, dust mites, mold spores, and other allergens as well as pollutants)• Hygrostat-controlled dehumidification automation with target value selection between 30 and 80 % r.H. in 5 % steps• As soon as the desired humidity level is reached, the compressor automatically turns off. The fan continues to run to keep the air clean. If the level is exceeded, the device activates automatically.• Suitable for rooms up to 15 m² / 37 m³• Dehumidification capacity max. 12 liters / 24 hours• Air quality display with color LED• Display of relative humidity• Continuous operation for continuous dehumidification in unattended rooms• Timer function (1-24 hours)• Night mode (whisper quiet)• Auto-restart function (memory function)• Overflow protection – Device switches off after reaching the maximum capacity of the water tank.• Warning signal for full water tank• Water container approx. 2.5 liters• Two-stage blower• Connection option for a drain hose for continuous operation• Laundry drying function  Technical data  dehumidification performance at 30 °C / 80 % r.H. 10 liters / day air volume 90 m³/ h Maximum room size 20 m² (50 m³) Minimum room size 4 m² (10 m³) temperature range 5 - 32°C  moisture range 30 - 80 % r.F. Voltage 220 - 240 V/50 Hz rated current consumption max. 1.4 A Power consumption max. 245W Recommended Coverage 10 A Cable length approx. 1.8 m Plug EU plug with Swiss adapter refrigerant R290 (30g) GWP3 water bucket 2.5 Liter operating noise 45 dB(A) at 1 m distance 42 dB(A) at a distance of 2.5 m Dimensions L x W x H 245 x 245 x 500 mm Weight 9.5 kg defrosting automatic electronic, recirculation dehumidification automation Hygrostatgesteuert Ventilator radial, 2-stage blower automatic shut-off when bucket is full and prefilter and HEPA-Filter yes, efficiency 95% Timer and Continuous operation possible and Laundry drying mode and Display shows current room humidity, set air humidity, air quality Night mode and memory function yes (automatically saves set values) hose connection yes, short hose piece included in the delivery (10 mm) guarantee 2 years Documents / Downloads   User Manual German   User manual French   User manual Italian   User manual English

Learn more More Fewer

Comfort, design, and high air performance   This dehumidifier impresses with its elegant design and thoughtful functionality. Its diverse features include a total of four operating modes. Here, the dehumidifier offers a hygrostat-controlled dehumidification automatic with a target value selection between 35 and 85% relative humidity in comfortable 5% increments, including an optional turbo fan.   A popular alternative to the dehumidification automatic function is the comfort function, where the humidity level is automatically adjusted to a comfortable value depending on the temperature. Additional operating modes include a laundry drying function and a permanent function.     Comfort function: Temperature-dependent air dehumidification   To achieve an optimal indoor climate, room temperature and humidity must be coordinated. This is exactly where temperature-dependent dehumidification comes into play. The device adjusts the humidity level based on temperature to the optimal value. The comfort function is particularly recommended when using programmable heating systems. If the room temperature changes during the day or at night, the dehumidifier automatically adjusts its dehumidification performance. This protects against mold formation and saves electricity.      Permanent air circulation   In this model, the compressor (= dehumidification) stops when the desired humidity level is reached, while the fan runs continuously to circulate the room air.     Practical Functions   When drying residential and office spaces of up to around 40 m², this dryer is an absolutely reliable partner. Various details simplify operation, such as the viewing window on the tank, which makes the fill level easily recognizable, the practical timer function, the fill level warning light when the water container is full, and the overflow protection with automatic shut-off. The air filter is easy to remove and wash. When the tank is full, a float automatically interrupts operation.     Auto-Restart Function   The auto-restart function (or memory function) allows the device to restart with unchanged settings after a power interruption as soon as the power supply is restored. This makes the dehumidifier suitable for use with a timer.     Gentle laundry drying with dehumidifiers In addition to dehumidifying the room air, a dehumidifier can be used to significantly accelerate the drying of laundry – either as a support or as a complete replacement for a conventional tumble dryer. The laundry drying function (or textile drying mode or SuperDry function) is comparable to traditional air drying outdoors. Dehumidifiers offer the advantage that laundry is dried gently, just like in nature. Colors remain vibrant, and clothing has a longer lifespan than with conventional tumble dryers, all while consuming significantly less electricity. Additionally, delicate materials such as wool, silk, or synthetic fibers can be dried without concerns.     Environmentally friendly refrigerant R290 Annually, several million tons of environmentally harmful CO2 emissions (greenhouse gases) are released into the air due to synthetic refrigerants. Therefore, the use of alternative refrigerants is one of our most important goals. By using propane (R290) as a refrigerant, this air dehumidifier makes a valuable contribution to climate protection. The natural refrigerant propane (R290) is an organic compound and belongs to the hydrocarbons. Unlike synthetic refrigerants, environmentally friendly propane (R290) has neither ozone depletion potential (ODP=0) nor a significant greenhouse effect (GWP=3).   "Supplement plus for the environment: Due to its excellent thermodynamic properties, propane (R290) is a particularly energy-efficient refrigerant, thereby additionally reducing your energy costs."     Advantages at a Glance   • Hygrostat-controlled dehumidification automation with target value selection between 35 and 85 % r.H. in 5 % steps• As soon as the desired humidity level is reached, the compressor (i.e., the dehumidification) automatically pauses. The fan continues to run to determine the actual humidity in the room. If it exceeds the limit, the device automatically switches back on.• Comfort operation for temperature-dependent automatic control of humidity for optimal room climate at all times• Continuous operation• Auto-restart function for use with an external timer• Display of relative humidity• Easily accessible air filter, easy to clean. Filters pet hair, lint, fluff, dust, and prevents bacterial growth.• Laundry drying function• Timer Function• Recirculation defrost automatic• Connection for external condensate drainage• 3 fan speeds• Level warning light when water tank is full• Automatic shutdown when tank is full thanks to float   Technical data  dehumidification performance at 30 °C / 80 % r.H. 16 liters / day air volume 150 m³/ h Maximum room size 40 m² (100 m³) Minimum room size 4 m² (15 m³) temperature range 5 - 32°C moisture range 35 - 85 % r.F. Voltage 220 - 240 V/50 Hz rated current consumption max. 2.2 A Power consumption max. 430W Recommended Coverage 10 A Cable length approx. 1.6 m Plug EU plug with Swiss adapter refrigerant R290 (75g) GWP3 water bucket 3 Liter operating noise 46 dB(A) at 1 m distance 43 dB(A) at a distance of 2.5 m Dimensions L x W x H 245 x 350 x 510 mm Weight 15 kg defrosting automatic Recirculation, electronic dehumidification automation Hygrostatgesteuert Ventilator radial, 3-stage blower automatic shut-off when bucket is full and prefilter and Timer and Continuous operation possible and Laundry drying mode and Display shows current room humidity, set air humidity memory function yes (automatically saves set values) hose connection yes, short hose piece included in the delivery guarantee 2 years Documents / Downloads   User Manual German   User manual French   User manual Italian   User manual English

Learn more More Fewer

Good, affordable household dehumidifier This device has been manufactured for many years and has been continuously developed. The current version features an appealing design and has been brought up to the latest technical standards.  Comfortable operation The operation is carried out via a clear operator panel with a display at the top, through which the desired target humidity can be entered in 5% increments. Continuous operation is also possible. The integrated hygrostat then automatically implements this target setting and self-regulates the performance of the compressor and the two-stage blower. The display shows you, among other things, the current value of the relative humidity in the room, the current room temperature, and the entered target value. Furthermore, the dryer has a timer function, an automatic fault diagnosis system, and a memory function. This memory function ensures that the set humidity value and the operating mode remain stored even after switching off or in the event of a power failure. This makes this model suitable for operation with a timer, for example, if you only want to run it during off-peak hours. The water that is extracted from the air is collected in the bucket placed at the front. A float automatically interrupts the operation when the bucket is full. Alternatively, the water can also be drained directly through a connectable hose into a lower outlet. The hose must be laid with a downward slope, as no pump is included in the device. The hose connection is particularly well designed in this model: if the hose is not permeable or is incorrectly laid (kinked, insufficient slope, etc.), the water is automatically redirected into the bucket, which automatically shuts off the device when full. In other models, backed-up water can lead to leakage from the bottom, which is prevented in this model.  Also suitable for laundry drying The combination of good dehumidifying power and appealing airflow makes this dehumidifier also a clothes dryer, capable of drying 1-2 loads of laundry per day in a temperate environment. Dehumidifiers offer the advantage that laundry is dried gently, as in nature. Colors remain vibrant, and clothing has a longer lifespan than with conventional tumble dryers, all while consuming significantly less electricity. Additionally, delicate materials such as wool, silk, or synthetic fibers can be dried without concerns.  Permanent air circulation In this model, the compressor (= dehumidification) stops when the desired humidity level is reached, while the fan runs continuously to circulate the room air.  Environmentally friendly refrigerant "Every year, several million tons of environmentally harmful CO2 emissions (greenhouse gases) are released into the air due to synthetic refrigerants. Therefore, the use of alternative refrigerants is one of our most important goals. By using propane (R290) as a refrigerant, this dehumidifier makes a valuable contribution to climate protection." The natural refrigerant propane (R290) is an organic compound and belongs to the hydrocarbons. Unlike synthetic refrigerants, environmentally friendly propane (R290) has neither ozone depletion potential (ODP=0) nor a significant greenhouse effect (GWP=3).Additional plus for the environment: Due to its excellent thermodynamic properties, propane (R290) is a particularly energy-efficient refrigerant, thereby further reducing your energy costs.  Advantages at a Glance • Hygrostat-controlled dehumidification automation with target value selection between 30 and 80 % r.H. in 5 % stepsAs soon as the desired humidity level is reached, the compressor pauses until the humidity in the room increases again (the fan continues to run to determine the true room humidity).• Continuous operation possible• Display of the desired humidity, the current humidity, and the current room temperature• Memory function•  Automatic fault diagnosis system•  Laundry drying function•  Easily accessible air filter, easy to clean. Filters pet hair, lint, fluff, dust, and prevents bacterial growth.• Timer Function•  Direct hose connection• 2 fan speeds•  Level warning light when water tank is full•  Overflow protection with automatic shut-off  Technical data  dehumidification performance at 30 °C / 80 % r.H. 20 liters / day air volume 150 m³/ h Maximum room size 50 m² (125 m³) Minimum room size 4 m² (15 m³) temperature range 5 - 32°C Selectable target moisture Achievable target moisture 30 - 80 % r.F. 35 - 80 % (lamella evaporator) Voltage 220 - 240 V/50 Hz rated current consumption max. 1.8 A Power consumption max. 420W Recommended Coverage 10 A Cable length approx. 1.5 m Plug EU plug with Swiss adapter refrigerant R290 (86g) GWP3 water bucket 3 Liter operating noise 43 dB(A) at 1 m distance 40 dB(A) at a distance of 2.5 m Dimensions L x W x H 253 x 340 x 570 mm Weight 12.5 kg defrosting automatic Electronic, Recirculation dehumidification automation Hygrostatgesteuert Ventilator radial, 2-stage blower automatic shut-off when bucket is full and prefilter and Timer and Continuous operation possible and Laundry drying mode and Display shows current room humidity, set air humidity memory function yes (automatically saves set values) hose connection yes, suitable hose 12mm inner diameter guarantee 2 years       Documents / Downloads   User Manual German   User manual French   User manual Italian   User manual English

Learn more More Fewer

Compact Dehumidifier for Basements, Archives & Laundry Drying Efficient humidity control with LED status display, convenience functions, and energy-saving continuous operation. The TTK 72 E is an affordable, compact dehumidifier for basements, archives, and faster laundry drying. An integrated LED display provides information about the current humidity status in the room at all times: Blue: below 55% RH Green: 55–70% RH (optimal range) Red: above 70% RH Convenient Functions In addition to automatic mode (55% RH), the unit features hygrostat-controlled automatic dehumidification (30–80% RH in 5% increments), a permanent mode, and a ventilation function. Equipment includes a laundry drying function and timer, a fill level warning light, overflow protection with automatic shut-off, a washable air filter, and a connection for an external condensate drain.As soon as the desired target humidity is reached, the compressor switches off to save energy. The fan generally continues to run for about 3 minutes to blow off residual moisture from the evaporator and then also switches off. Gentle Laundry Drying The integrated laundry drying function allows for particularly gentle drying of materials – energy-efficient and color-preserving. Delicate textiles such as wool or silk can also be treated without any problems. Recommended humidity levels: Cupboard dry: 46% RH Iron dry: 58% RH Semi-dry: 65% RH New Refrigerant R290 The TTK 72 E uses the natural refrigerant propane (R290). It has no ozone depletion potential (ODP=0), a very low greenhouse effect (GWP=3), and is highly energy-efficient – beneficial for the environment and operating costs. Features: Automatic dehumidification 30–80% RH LED humidity display (3 colors) Permanent mode & ventilation Laundry drying function Timer function Automatic defrosting External condensate drain 2 fan speeds Overflow protection with auto-shutoff Washable air filter Technical Data Article number 1120000073 Dehumidification capacity max. 20 l / 24h (at 30 °C / 80% RH) Recommended room size 50 m² / 125 m³ Airflow rate (speed 1 / 2) 180 / 195 m³/h Temperature range 5 – 32 °C Humidity range 30 – 80% RH Power consumption 320 W Weight 13 kg Water tank 5.5 liters Sound level 48 dB(A) (1 m) Fan 2-speed Refrigerant R290 (60 g) GWP 3 Power cable Approx. 1.8 m with EU plug and fixed adapter for Switzerland. Warranty 2 years

Learn more More Fewer

Dehumidifier with EPA filter TTK 70 HEPA – Dehumidifying and air purifying in one device 18 liters of dehumidification performance per day, integrated EPA air filtration, and automatic humidity control for living rooms, bedrooms, basements, and rooms up to 45 m². Extra-large tank. The TTK 70 HEPA combines two important functions for a pleasant indoor climate: It reliably reduces excess humidity while simultaneously supporting air purification. With a dehumidification capacity of 18 liters per day at 30 °C and 80% relative humidity, this powerful dehumidifier is suitable for rooms up to 45 m². The integrated EPA filter with a filtration efficiency of 95% adds an extra cleaning stage to the dehumidification process. The filter helps reduce mold spores, pollen, dust mite allergens, bacteria, viruses, and fine dust from the air passing through the device. This makes the TTK 70 HEPA particularly well-suited for living rooms, bedrooms, home offices, basements, and households where, in addition to controlled humidity, importance is placed on improved indoor air quality. The intelligent automatic humidity control monitors the relative humidity and allows for convenient regulation of the desired humidity level. An integrated air quality indicator provides additional information about the current state of the indoor air. The color LED on the front makes monitoring particularly easy: the current state is visible at a glance. With its generous water tank, practical hose connection, and auto-restart function, the TTK 70 HEPA is also suitable for longer periods of operation. The natural refrigerant R290 with a GWP of 3 also supports environmentally conscious and efficient operation. Features: 2-in-1: Dehumidifier and air purifier 18 liters dehumidification performance per day For rooms up to 45 m² Integrated EPA filter 95% filtration efficiency Filtration of various air pollutants and particles Air quality indicator Room temperature display Automatic humidity control LED display and color LED Auto-restart function Child lock Direct hose connection Natural refrigerant R290 GS-tested Dehumidifier and air purifier in one device A conventional dehumidifier reduces humidity, while an air purifier primarily filters particles from the indoor air. The TTK 70 HEPA combines both functions in one compact device, providing a practical solution for humidity regulation and air purification. While the compressor removes moisture from the room air, the air flowing through the device is additionally passed through the EPA filter. This allows for controlled indoor humidity while simultaneously cleaning the room air of various particles. The device is therefore suitable for anyone looking for a dehumidifier with an air filter who does not want to set up two separate devices. EPA filter with 95% filtration efficiency The integrated EPA filter adds an additional indoor air purification function to the TTK 70 HEPA. With a filtration efficiency of 95%, this filter stage reduces a large portion of the particles contained in the airflow. The EPA filter can assist especially with pollen, dust, fine dust, mold spores, and other particles present in the indoor air. This makes the TTK 70 HEPA interesting not only as a dehumidifier but also as an air purifier with an EPA filter. The filter should be checked and cleaned regularly according to usage, or replaced if necessary. Detailed instructions on filter maintenance and replacement can be found in the respective operating manual. Dehumidifier against mold – Targeting excess humidity Excessive humidity can promote condensation, especially on cold surfaces, thereby creating an unfavorable indoor climate. A dehumidifier against mold tackles a primary cause: it reduces excess moisture in the indoor air. The TTK 70 HEPA supports automatic monitoring of indoor humidity and helps maintain a comfortable humidity range. At the same time, the integrated EPA filter can remove particles from the air flowing through it. Important: If there is already significant mold growth, a dehumidifier does not replace professional cause analysis and remediation. Structural causes such as penetrating moisture, thermal bridges, or leaks must be addressed independently. Pleasant indoor climate for living spaces and allergy sufferers Living spaces generate various sources of moisture every day: showering, cooking, drying laundry, and normal room use all increase humidity. Simultaneously, pollen, dust, and other particles enter the indoor air. The TTK 70 HEPA therefore combines humidity regulation and air filtration. With a dehumidification capacity of 18 liters per day at 30 °C / 80% RH, it is suitable for rooms up to 45 m². The automatic control ensures comfortable operation without having to constantly monitor the desired humidity manually. The integrated child lock also prevents accidental changes to the settings. Air quality indicator with practical color LED The TTK 70 HEPA makes the state of the indoor air easy to see. The integrated color LED shows the current air condition at a glance. This allows you to quickly recognize whether the indoor air is within the desired range or if an adjustment to the settings is sensible. Additionally, the device displays important information about the current indoor climate. This provides relevant data for monitoring humidity and indoor air quality directly on the device. Automatic humidity control for comfortable operation The integrated automatic humidity control manages moisture levels automatically. This means the device does not need to be switched on and off manually all the time. The TTK 70 HEPA adapts its operation to the measured indoor humidity, thus supporting a constantly pleasant indoor climate. This is particularly practical in the bedroom, living room, home office, or basement when humidity needs to be controlled over longer periods. For long-term operation with hose connection For particularly comfortable operation, condensation can be drained directly via the existing hose connection. This allows for longer or unattended operation, provided that the condensate drain is set up accordingly. This makes the TTK 70 HEPA suitable not only for living rooms but also for basements, hobby rooms, and other areas where continuous dehumidification is required. Auto-restart function for reliable operation Following an interruption in the power supply, the device can resume operation automatically thanks to the auto-restart function. This makes the TTK 70 HEPA suitable for scenarios where the device does not need to be started manually every time. Natural refrigerant R290 The TTK 70 HEPA uses the natural refrigerant R290 (propane). This refrigerant has a very low greenhouse potential with a GWP of 3 and is increasingly used in modern refrigeration and air conditioning equipment. The use of R290 combines the powerful compressor technology of the dehumidifier with a refrigerant that has a low global warming potential. Advantages of the TTK 70 HEPA at a glance Powerful dehumidifier with 18 liters per day at 30 °C / 80% RH Suitable for rooms up to 45 m² Extra-large 6.5-liter tank Additional air purification through integrated EPA filter 95% filtration efficiency of the filter Suitable for reducing various particles from the indoor air Automatic regulation of indoor humidity Air quality indicator Practical color LED for quick monitoring Direct hose connection for longer continuous operation Auto-restart function after power failure Integrated child lock Natural refrigerant R290, GWP 3 GS-tested Suitable for these areas of application Living rooms and open living areas Bedrooms Home offices and studies Basements and hobby rooms Rooms with increased humidity Rooms with high dust exposure Living spaces during pollen season Households where air filtration is desired in addition to dehumidification Areas from 4 to approx. 45 m² Technical data Device type Dehumidifier with EPA air filtration Device function Dehumidification and air filtration Dehumidification capacity at 30 °C / 80% RH 18 liters / day Minimum / maximum room size 4 / 45 m² Filter Pre-filter + replaceable EPA filter, 1 pc. included Filter filtration efficiency 95% Color LED for air quality indication yes Automatic humidity control yes Room humidity display yes Room temperature display yes Auto-restart yes Child lock yes Water tank 6.5 liters Water level indicator yes Automatic shut-off when water tank is full yes Hose connection yes, suitable hose: 10 mm inner diameter Refrigerant R290 (propane) / 60 g GWP (Global Warming Potential) 3 Refrigerant quantity according to nameplate Operating mode Compressor dehumidification Automatic defrost yes Fan integrated Power connection 230 V / 50 Hz Approx. 1.8 m connection cable with EU plug + fixed adapter for Switzerland Power consumption 420 W Dimensions (H x W x D) 565 x 340 x 225 mm Sound pressure level 48 dB(A) Ambient temperature 5 – 32 °C Relative humidity according to manufacturer specifications Weight 13 kg Certificates GS-tested Warranty 2 years Frequently asked questions about the dehumidifier with EPA filter TTK 70 HEPA What is an EPA filter? EPA stands for Efficient Particulate Air. EPA filters belong to the high-efficiency particulate filters and are used to separate fine particles from the air. The EPA filter of the TTK 70 HEPA has a specified filtration efficiency of 95%. How much water does the TTK 70 HEPA remove from the air? The specified dehumidification capacity is 18 liters per day at 30 °C and 80% relative humidity. The actual dehumidification performance achieved depends on the respective room conditions. What room size is the TTK 70 HEPA suitable for? The TTK 70 HEPA is suitable for rooms up to approx. 45 m². The actual power required can vary depending on room height, temperature, moisture load, building structure, and usage. Is the TTK 70 HEPA an air purifier? The TTK 70 HEPA combines the functions of a dehumidifier and air filter. In addition to dehumidification, the room air is passed through the integrated EPA filter. This allows the device to contribute to the reduction of particles in the indoor air in addition to reducing moisture. Does the TTK 70 HEPA help against mold? By reducing indoor humidity, the device can counteract conditions that favor mold growth. The EPA filter can additionally remove particles such as mold spores from the air passing through it. However, if there is an existing mold infestation, the causes of moisture must also be professionally remedied. Can the TTK 70 HEPA be operated continuously? Yes. Via the direct hose connection, condensation can be drained continuously. This allows for longer or unattended operation, provided that the condensate drain is set up correctly. What refrigerant does the TTK 70 HEPA use? The TTK 70 HEPA uses the natural refrigerant R290 (propane) with a GWP of 3.

Learn more More Fewer

Reliable dehumidifier with solid drying performance This device has been manufactured for many years and has been continuously developed. The current version features an appealing design and has been brought up to the latest technical standards.  Comfortable operation The operation is carried out via a clear operator panel with a display at the top, through which the desired target humidity can be entered in 5% increments. Continuous operation is also possible. The integrated hygrostat then automatically implements this target setting and self-regulates the performance of the compressor and the two-stage blower. The display shows you, among other things, the current value of the relative humidity in the room, the current room temperature, and the entered target value. Furthermore, the dryer has a timer function, an automatic fault diagnosis system, and a memory function. This memory function ensures that the set humidity value and the operating mode remain stored even after switching off or in the event of a power failure. This makes this model suitable for operation with a timer, for example, if you only want to run it during off-peak hours. The water that is extracted from the air is collected in the bucket placed at the front. A float automatically interrupts the operation when the bucket is full. Alternatively, the water can also be drained directly through a connectable hose into a lower-lying drain. The hose must be laid with a downward slope, as no pump is included in the device.  Also suitable for laundry drying The combination of good dehumidifying power and appealing airflow makes this dehumidifier also a clothes dryer, capable of drying 2-3 loads of laundry per day in a temperate environment. Dehumidifiers offer the advantage that laundry is dried gently, as in nature. Colors remain vibrant, and clothing has a longer lifespan than with conventional dryers, all while consuming significantly less electricity. Additionally, delicate materials such as wool, silk, or synthetic fibers can be dried without concern.  Permanent air circulation In this model, the compressor (= dehumidification) stops when the desired humidity level is reached, while the fan runs continuously to circulate the room air.  Environmentally friendly refrigerant "Every year, several million tons of environmentally harmful CO2 emissions (greenhouse gases) are released into the air due to synthetic refrigerants. Therefore, the use of alternative refrigerants is one of our most important goals. By using propane (R290) as a refrigerant, this dehumidifier makes a valuable contribution to climate protection." The natural refrigerant propane (R290) is an organic compound and belongs to the hydrocarbons. Unlike synthetic refrigerants, environmentally friendly propane (R290) has neither ozone depletion potential (ODP=0) nor a significant greenhouse effect (GWP=3).Additional plus for the environment: Due to its excellent thermodynamic properties, propane (R290) is a particularly energy-efficient refrigerant, thereby further reducing your energy costs.  Advantages at a Glance • Hygrostat-controlled dehumidification automation with target value selection between 30 and 80 % r.H. in 5 % stepsAs soon as the desired humidity level is reached, the compressor pauses until the humidity in the room increases again (the fan continues to run to determine the true room humidity).• Continuous operation possible• Display of the desired humidity, the current humidity, and the current room temperature• Memory function•  Automatic fault diagnosis system•  Laundry drying function•  Easily accessible air filter, easy to clean. Filters pet hair, lint, fluff, dust, and prevents bacterial growth.• Timer Function•  Direct hose connection• 2 fan speeds•  Level warning light when water tank is full•  Overflow protection with automatic shut-off•  Hot gas defrosting: faster automatic self-defrosting in cooler environments.   Technical data  dehumidification performance at 30 °C / 80 % r.H. 25 liters / day air volume 215 m³/ h Maximum room size 60 m² (150 m³) Minimum room size 4 m² (15 m³) temperature range 5 - 32°C Selectable target moisture Achievable target moisture 30 - 80 % r.F. 35 - 80 % (lamella evaporator) Voltage 220 - 240 V/50 Hz rated current consumption max. 2.4 A Power consumption max. 570W Recommended Coverage 10 A Cable length approx. 1.6 m Plug EU plug with Swiss adapter refrigerant R290 (122g) GWP3 water bucket 4.3 Liter operating noise 50 dB(A) at 1 m distance 47 dB(A) at a distance of 2.5 m Dimensions L x W x H 274 x 390 x 612 mm Weight 15.5 kg defrosting automatic Heissgas dehumidification automation Hygrostatgesteuert Ventilator radial, 2-stage blower automatic shut-off when bucket is full and prefilter and Timer and Continuous operation possible and Laundry drying mode and Display shows current room humidity, set air humidity memory function yes (automatically saves set values) hose connection yes, suitable hose 12mm inner diameter Similar models Krüger Airsec 3000 guarantee 2 years   Documents / Downloads   User Manual German   User manual French   User manual Italian   User manual English

Learn more More Fewer

The adsorption dehumidifier TTR 57 E is designed for dehumidification and keeping dry of rooms up to an area of 40 m². It offers significant advantages, especially in cooler rooms. Performance Features and Technology Unlike conventional condensation dehumidifiers, which lose performance at low room temperatures, the TTR 57 E has almost constant dehumidification performance down to freezing point. The underlying adsorption technology offers the following specific advantages: No compressor, refrigerant, or defrosting breaks required. Energy-efficient operation. Quiet operation. Features: Dehumidification up to 40 m² Adsorption technology Dehumidification capacity up to 9 l/24h LED color display 3 fan speeds Laundry drying function 24-hour timer Weight 7.5 kg Functionality and Performance The device features an LED color display that visualizes the current humidity level in the room, allowing for quick checking of optimal humidity. With a dehumidification capacity of up to 9 liters per day, the relative indoor air humidity can be reduced to up to 40%. The compact device weighs only 7.5 kg. Areas of Application The TTR 57 E is suitable for various applications for preventing moisture damage and mold formation: Cool basements (for protecting building structure and stored goods). Unheated garages (for reducing rust formation). Conservatories (for reducing condensation). Boats/cabins (for protection against moisture damage). Laundry drying, especially in cooler laundry rooms. Technical Details and Operating Modes The TTR 57 E offers the following selectable operating modes and functions: Target value pre-selection 40%, 50%, 60% or 70% relative humidity. Continuous operation Continuous dehumidification at maximum performance. Laundry drying function Cabinet dry (46%), Iron dry (58%), Pre-dried (65% rel. humidity). Ventilation mode Three adjustable fan speeds. 24-hour timer Programming of the switch-on or switch-off time. Additional Features Fill level warning light, connection for external condensate drain, washable air and activated carbon filters. Optional HEPA Filter H13 In addition to the coarse dust filter, which is included in the scope of delivery, an optional HEPA filter category 13 is available for this model. This filters fine dust, pollen as well as viruses and bacteria from the air with a purity level of over 99.9%. This HEPA filter is therefore very popular with asthmatics, for example, when drying hung bedding, but also for simultaneous air purification in living areas. Technical Data General & Product Information <trotec artikelnr.=""></trotec> 1120000065 Recommended room size (area) 40 m² (100 m³) Operating principle Adsorption dehumidification Dimensions & Weight Length with / without packaging 238 /232 mm Width with / without packaging 388 / 340 mm Height with / without packaging 570 / 511 mm Weight with / without packaging 8.5 / 7.5 kg Technical Data (Dehumidification) Dehumidification capacity (at 8°C / 80 % RH) 7.5 l/24h Dehumidification capacity (at 30°C / 80 % RH) 8.5 l/24h Dehumidification capacity max. 9 l/24h Water tank capacity 5 l Condensate drain Hose connection possible (recommended hose size: 11 mm inner diameter) Ventilation & Air Volume Fan speeds 3 Fan type radial Air volume (Max.) 185 m³/h Energy & Electrical Data Mains connection and frequency 220 - 240 V, 50 Hz Power consumption 730 W Rated current consumption 3.7 A Recommended fuse protection 10 A Cable + plug 1.8 m, EU plug with fixed adapter for Switzerland Operating conditions Temperature range min. / max. 1° / 32 ° C Humidity min. / max. 35 % / 90 % RH Functions & Features Functions Adjustable blow-out direction, LED display, Timer function Automatic dehumidification program-controlled Room air filter washable, easily accessible (activated carbon filter, air filter included) Condensate tank monitoring Tank available, fill level warning light, overflow protection with automatic shutdown Mobility Carrying/transport handle(s) Housing design Plastic Sound level Sound level (1m / 3m distance, Max.) 47 / 44 dB(A) Warranty 2 years

Learn more More Fewer

Trotec TTK 99 HEPA Dehumidifier and Air Purifier for Households and Living Spaces Combined dehumidifier and HEPA air purifier for basements, garages, laundry rooms, and living spaces – efficient humidity control, improved air quality, and reliable protection against mold, allergens, and fine dust. The Trotec TTK 99 HEPA is a modern dehumidifier with an integrated air purification function, specifically developed for household use. It is ideal for keeping damp basements, garages, and laundry rooms dry, as well as for efficiently supporting indoor laundry drying. With a dehumidification capacity of up to 31 liters per day, the device reliably ensures stable humidity levels and protects rooms of up to approx. 80 m² from mold formation, moisture damage, and musty odors. Thanks to the integrated HEPA and pre-filter system, the indoor air is purified at the same time. This significantly reduces pollutants such as dust, pollen, bacteria, viruses, and mold spores – for a noticeably healthier indoor climate. The combination of dehumidification and air purification makes the TTK 99 HEPA a versatile all-rounder for modern households with high demands on air quality and comfort. Features: Combined dehumidifier & air purifier HEPA filter (E11) against pollen & fine dust Up to 31 L/day dehumidification capacity Suitable for rooms up to approx. 80 m² LED air quality indicator (blue/green/red) Hygrostat-controlled automatic operation Laundry drying function Timer function (24 h) Integrated child lock Memory function after power failure Direct hose connection possible 2-speed fan Automatic shutdown when tank is full Healthy indoor air through intelligent moisture and air purification The TTK 99 HEPA continuously monitors humidity and automatically adjusts operation to current room conditions. This keeps humidity consistently in the optimal range between 30 and 80% RH. The integrated air quality indicator provides information on the state of the indoor air at all times. This allows you to see at a glance whether the air is too dry, optimal, or too humid. At the same time, the HEPA filter system ensures that harmful particles such as pollen, dust, bacteria, and mold spores are effectively removed from the air – ideal for allergy sufferers and health-conscious households. Efficient dehumidification and flexible use With its high dehumidification capacity, the TTK 99 HEPA is optimally suited for medium-sized living and utility rooms. It reliably ensures dry conditions, particularly in basements, garages, and laundry rooms. The device also efficiently supports laundry drying: damp laundry dries significantly faster, which simultaneously reduces humidity in the room. Energy-optimized operation allows for economical use in everyday life while maintaining high performance. Convenient operation and intelligent automation The integrated hygrostat allows for precise setting of the desired humidity. The TTK 99 HEPA then works fully automatically and regulates operation independently. Various operating modes such as automatic, continuous operation, laundry drying, and night mode ensure maximum flexibility in everyday use. Additional functions like the timer, child lock, and auto-restart increase ease of use and safety in daily operation. Combined dehumidification and air purification The Trotec TTK 99 HEPA operates on the condensation principle. Damp indoor air is drawn in, cooled, and dehumidified. The condensed water is safely drained into the tank or via a hose. In parallel, the air is passed through a two-stage filter system. The pre-filter traps coarse particles, while the HEPA filter (E11) removes the finest pollutants from the air. This combination ensures a permanently dry and hygienically clean indoor climate. Typical application areas Basements and lower levels Garages and hobby rooms Laundry rooms Living rooms and bedrooms Private archives Rooms for laundry drying Small storage rooms Why combined dehumidification and air purification is useful Moisture and pollutants often occur in indoor spaces simultaneously. While excessive humidity promotes mold, dust, pollen, and germs impair air quality. The TTK 99 HEPA solves both problems in one device: it reduces humidity and filters the air at the same time – for a noticeably healthier indoor climate. Advantages at a glance Combined dehumidifier and HEPA air purifier Up to 31 L/24 h dehumidification capacity Suitable for rooms up to approx. 80 m² HEPA filter against allergens and fine dust LED air quality indicator Laundry drying function Hygrostat-controlled automatic operation Timer and night mode Integrated child lock Direct hose connection possible Very versatile household use Technical data Dehumidification capacity 31 L / 24 h (30 °C / 80 % RH) Air volume 170 m³/h Room size up to 80 m² Temperature range 5 – 32 °C Humidity range 35 – 100 % RH Power consumption max. 720 W Power supply 220–240 V / 50 Hz Connection cable 1.8 m with EU plug and fixed adapter for Switzerland Sound pressure level 51 / 48 dB(A) Water tank 4 liters Refrigerant R290 Dimensions 250 × 370 × 585 mm Weight 17 kg Warranty 2 years

Learn more More Fewer

A compact dehumidifier with adsorption technology. Adsorption is useful where the room air is cold, or where very low humidity levels are to be achieved. The "DS3" is also ideal for quick laundry drying in cool basements..In contrast to condensation dehumidifiers (dehumidifiers with a compressor), dehumidifiers with adsorption technology have an almost constant dehumidification performance even at low temperatures. They require virtually no lead time from startup until effective dehumidification begins. Due to their compressor-free design, these dryers are lightweight at only 7.5 kg. Technologically, the device would even extract water from the air below freezing point; however, the water then freezes in the collection tray, making 0.5°C the limit for use. Even at warmer temperatures, drying with adsorption dryers is straightforward, but the power consumption per liter of water extracted in temperate rooms is higher than that of compressor dehumidifiers (condensation dehumidifiers). The crossover point is around 8-10°C, meaning that below this value, adsorption dryers are more efficient, while above it, condensation dryers are more effective.Once the target humidity is reached, the dehumidification operation stops, while the ventilation continues for a few more minutes until the device has cooled down sufficiently. Subsequently, dehumidification and ventilation pause until the humidity in the room rises above the desired target humidity level again. The ventilation is powerful and can be adjusted in 3 stages. This is particularly advantageous when drying laundry and significantly speeds up the process. With the vertically adjustable air outlet louver, the dry air can also be directed in the desired direction. The wind noise is audible even at the lowest setting, so the DS3 is only partially suitable for very quiet bedrooms.Special function air purification with HEPA filterThe DS3 can also be used as an air purifier. A suitable HEPA filter available from us can be placed in the air intake area. This filters the air with a purity rate of over 99.9% and removes all airborne particles such as pollen, fine dust, spores, viruses, and germs from the air. The air purification mode can run together with the dehumidification operation, but also without dehumidification thanks to the pure air circulation level. The filter can be ordered individually.  Characteristics of the DS3• Dehumidification capacity of up to 9.5 liters per day.• Adsorption technology without a compressor and without refrigerants.• already at cool 0.5°C a good dehumidification performance.• significantly larger water bucket (5 liters) than comparable devices, auto-stop when full tank including warning light.• Electric hygrostat (LED) for regulating and setting the desired humidity.• Humidity control in 10% steps from approx. 40% to 70% as well as continuous operation possible.• In addition to the standard mode, there are the following operating modes: Auto mode; Dry mode (Turbo) and Air purification mode* (additional *HEPA filter required).• Timer function to select the automatic remaining time or the start time between 1-24 hours.• Clear display including current humidity display and status overview.• Also suitable for continuous operation/continuous dehumidification.• SmartHome capable (via WLAN socket) + can be controlled via external timer switch (only possible with a few devices).• Memory function: no adjustments during power failure (device continues from where it was interrupted).• Possibility for direct hose connection for draining water into a lower outlet (suitable hose: 12mm inner diameter).• Absolutely maintenance-free.• Washable, antibacterial air filter.• Modern design and appealing appearance, therefore also very suitable for living spaces.• The device is immediately ready for use (no installation or assembly required).• Comparatively light in weight, easy mobility with side grip recesses.• Fulfillment of the WEEE standards.• TÜV "GS" tested as well as CE and EMC conformity.   scope of deliveryThe delivery includes the ready-to-plug-in device as well as an activated carbon net, which can be placed in the air intake area and slightly improves the air quality during operation. The HEPA filter is optional and is not included in the basic delivery.  application examples   • Drying of poorly insulated basements, garages, boats, caravans during the winter season • Laundry drying in cold laundry rooms • Drying of herbs and spices       Technical data   Tension 230V / 50Hz Power consumption max. 730W Sound pressure level (our measurement) Weakest fan stage: 1m distance 48 dB(A) 2.5m distance 44 dB(A) Strongest fan speed: 1m distance 55 dB(A) / ideal for laundry drying 2.5m distance 52 dB(A) fan         Weakest fan stage air volume approx. 170 m³/h Blow-out speed approx. 4.4 m/s. Strongest fan stage air volume approx. 270 m³/h Blow-out speed approx. 6.5 m/s. dehumidification performance   max. 9.5 liters per day (at 30°C / 80% r.H.) max. 9 liters per day at 8°C / 80% r.H.) condensate tank Approx. 5 liters and direct hose connection (12mm) refrigerant not available/adsorption technology Dimensions (H/W/D)   515 x 360 x 240 cm   Weight 7.5 Kg Ambient temperature 1°C ~ 32°C  Comparable devices EcoQ 9L Steady Area of application bus ca. 50 m² Swiss plug Yes   guarantee 2 years Documents/Downloads   User Manual German

Learn more More Fewer

Luftentfeuchter Trotec TTK 75 ECO Semiprofessioneller Bautrockner mit Betriebsstundenzähler und Heissgasabtauung, Rollkolbenkompressor und hoher Entfeuchtungsleistung. Ohne Hygrostat - das Gerät läuft im Dauerbetrieb und ist somit ideal für Baustellen und Sanierung von Wasserschäden. Der Trotec TTK 75 ECO ist ein robust gebauter Luftentfeuchter sowohl für professionelle Trocknungsaufgaben, wie auch für die Trockenhaltung von Kellern und Baustellen. Mit einer maximalen Entfeuchtungsleistung von 21 Litern pro 24 Stunden eignet sich das Gerät für Räume bis etwa 50 m² bzw. 125 m³. Kompakt und einfach zu transportieren Mit einem Gewicht von rund 20.5 kg gehört der TTK 75 ECO trotz Metall-Gehäuse zu den leichteren Geräten seiner Leistungsklasse. Der versenkbare Metall-Tragegriff erleichtert den Transport und ermöglicht einen einfachen Wechsel zwischen verschiedenen Einsatzorten. Die kompakten Abmessungen machen den Bautrockner auch für Räume geeignet, in denen grössere Fahrwagen-Geräte nur schwer eingesetzt werden können. Das Gerät lässt sich bequem über Treppen, durch enge Zugänge oder in kleinere Kellerräume transportieren. Heissgasabtauung für niedrige Temperaturen Die Heissgasabtauautomatik ermöglicht eine zuverlässige Entfeuchtung auch bei niedrigen Temperaturen. Das ist besonders bei der Bautrocknung, bei Wasserschäden und in unbeheizten Räumen von Vorteil. Durch die automatische Abtauung werden längere Unterbrechungen des Entfeuchtungsbetriebs reduziert. Dadurch eignet sich der TTK 75 ECO auch für länger dauernde professionelle Trocknungseinsätze. Rollkolbenkompressor für flexible Nutzung Der TTK 75 ECO verfügt über einen Rollkolbenkompressor. Dadurch kann das Gerät in verschiedenen Positionen transportiert und gelagert werden. Dies erleichtert insbesondere den Einsatz bei wechselnden Baustellen und Trocknungsarbeiten. Betriebsstundenzähler für professionelle Einsätze Ein integrierter Betriebsstundenzähler erfasst die Laufzeit des Gerätes. Damit lässt sich die Einsatzdauer bei Bautrocknungen, Wasserschadensanierungen, Vermietungen oder gewerblichen Trocknungsaufträgen nachvollziehen und dokumentieren. Dauerhafte Kondensatableitung Für längere Trocknungseinsätze kann das anfallende Kondenswasser über den vorgesehenen Kondensatablauf kontinuierlich abgeführt werden. Dadurch muss der Wasserbehälter nicht regelmässig manuell entleert werden. Umweltgerechtes Kältemittel R290 Als Kältemittel kommt das natürliche Propan R290 zum Einsatz. Mit einem sehr niedrigen Treibhauspotenzial ist R290 eine moderne Kältemittelalternative für effiziente Kompressor-Luftentfeuchter. Eigenschaften: Entfeuchtungsleistung max. 21 l/24 h 21 l/24 h bei 30 °C / 80 % r. F. Für Räume bis ca. 50 m² / 125 m³ Heissgasabtauautomatik Auch für kühlere Temperaturen geeignet Rollkolbenkompressor Versenkbarer Metall-Tragegriff Betriebsstundenzähler Umweltgerechtes Kältemittel R290 Wasserbehälter 4 Liter 4 Standfüsse Kein Hygrostat (Feuchtigkeitsregler), Gerät läuft im Dauerbetrieb Startet nach Stromunterbruch automatisch wieder Entfeuchtungsleistung bei 30 °C / 80 % r. F. Entfeuchtungsleistung: bis zu 21 Liter pro 24 Stunden Die Entfeuchtungsleistung des Trotec TTK 75 ECO beträgt unter der Referenzbedingung von konstanten 30 °C Raumtemperatur und 80 % relativer Luftfeuchtigkeit bis zu 21 Liter pro 24 Stunden. Je nach Raumtemperatur und vorhandener Luftfeuchtigkeit kann die tatsächliche Leistung abweichen. Geeignete Einsatzbereiche Der TTK 75 ECO wurde für anspruchsvolle Entfeuchtungs- und Trocknungsaufgaben entwickelt. Durch die Kombination aus kompakter Bauweise, Heissgasabtauung und professioneller Ausstattung eignet er sich unter anderem für: Bautrocknung Wasserschadensanierung Kellerräume und Nebenräume Estrich- und Putztrocknung Werkstätten und Lagerräume Gewerbliche Trocknungseinsätze Vermietung und wechselnde Baustellen Technische Daten Modell Trotec TTK 75 ECO Artikelnummer 1120001110 Entfeuchtungsleistung bei 30 °C / 80 % r. F. 21 l/24 h Geeignete Raumgrösse Bis ca. 50 m² / 125 m³ Wasserbehälter 4 l Abtausystem Heissgasabtauautomatik Kompressor Rollkolbenkompressor Kältemittel R290 (Propan) Gewicht Ca. 20,5 kg Abmessungen (B × T × H) 315 × 310 × 555 mm Betriebsstundenzähler Ja Stromanschluss Netzkabel ca. 3 m mit EU-Stecker + Fixadapter für die Schweiz Garantie 2 Jahre Hinweis zur angegebenen Entfeuchtungsleistung:Die Angabe von 21 l/24 h bei 30 °C / 80 % r. F. dient als Referenzwert für warme und feuchte Betriebsbedingungen. Die tatsächliche Entfeuchtungsleistung hängt von der jeweiligen Raumtemperatur, der relativen Luftfeuchtigkeit und den Einsatzbedingungen ab.

Learn more More Fewer

The Oasis dehumidifiers are among the widely used drying devices that have been successfully employed on construction sites and by private users for many years. The devices have now been revised and adapted to the latest state of technology with the newest environmentally friendly refrigerant R290 and improved efficiency. The Oasis D165 is suitable for basements and rooms up to 90m² and comes standard with a large bucket as well as a direct hose connection.Although visually very similar, the D165 dehumidifier has been completely revised in various respects compared to its predecessor:• improved efficiency• higher dehumidification performance• environmentally friendly refrigerant R290• improved automatic self-defrosting, thus usable down to 5°C (previously: 8°C)• reinforced front cover with spark guard bowl• reinforced, load-bearing wheelsThe dryer stands on 4 wheels but can also be mounted on a suitable wall bracket available from us if desired. The air intake area is at the back, where a filter cleans the moist air. The filter itself is easy to remove and clean. The dry air is blown out towards the front into the room. The Oasis is therefore ideal for general moisture control in a classic basement environment, for example in new buildings, but also for unattended continuous operation in temperature-controlled archives and on construction sites. For active laundry drying, the blower is rather too weak.The target humidity is regulated via a stepless hygrostat on the front. Once the set value is reached, the dehumidification operation pauses (the ventilation also stops) until the humidity rises again. The operation continues with the unchanged setting even after a power interruption. The D165 is therefore also suitable for operation with a timer, if you want to run the dryer, for example, only during off-peak hours. Thanks to the pipe evaporators, the D165 extracts water from the air even in low humidity ranges.The water is collected in the tank pushed in at the back, a float mechanically interrupts operation when full. Alternatively, a hose can be screwed onto the condensate collection tray (with a coupling / 3/4-inch thread), with the hose needing to have a slope towards the drain (no pump integrated in the device).usage examplesCellar Moisture: Ideal for damp cellars, old walls, and laundry rooms. Eliminates musty odors, stops mold growth, decomposition of masonry, and much more.Construction and Industrial Dryers: thanks to their handy, robust design, they are ideally suited for drying on construction sites and in the industry.Drying of Water Damage: The Oasis removes water from the air even in deep moisture areas through the pipe evaporators. This significantly accelerates the drying of water damage.dehumidification performanceThe dryer can be used thanks to hot gas defrosting over a wide temperature range from +5°C to +32°C, although, as with all condensation dryers, the dehumidifying power decreases in cooler environments. Examples of dehumidification performance and consumption under various (constant) environmental conditions:  30°C/80% r.H.: 28 liters / 24 h27°C/60% r.H.: 16.8 Liters / 24 h20°C/60% r.H.: 10.8 Liters / 24 h10°C/70% r.H.: 5.3 Liters / 24 h(r.H.=relative humidity)    Massive improvement regarding environmental compatibilityThe GWP (Global Warming Potential - impact on global warming) could be reduced by a factor of 800 (!) from 1430 (R134a) to less than 2 (R290). Furthermore, the D165 requires 10% less electricity while simultaneously increasing dehumidification performance by 14% (at room temperature 20°C, 60% r.H.). Technical data  Tension 230V / 50Hz Power consumption max. 360W Sound pressure level 1 m distance 54 dB(A) (our measurement) 2.5 m distance 51 dB(A) (our measurement) dehumidification performance max. 28 liters/day (30°C / 80% r.H.)  Bucket Capacity 9 liters, approx. 8 liters until operation interruption by float Compressor Rotary compressor  refrigerant R290 (150gr.) Dimensions (H x W x D)   60 x 38 x 36 cm (incl. wheels) Weight 23.5 Kg cessation of operations Hygrostatrad   Ambient temperature 5°C ~ 40°C  Area of application about 90m² Swiss plug Yes   hose connection Yes operating hour meter Yes guarantee 2 years    

Learn more More Fewer

This powerful dehumidifier, equipped with a generous tank and optional Wi-Fi function, is the ideal solution for the effective drying of large warehouses, archives, or basements. Additionally, it enables quick and efficient laundry drying.Despite its impressive dehumidification performance, this device is characterized by low energy consumption. It uses the modern refrigerant "R290", which significantly reduces environmental impact. With a "Global Warming Potential (GWP)" of only 3, it is 99.85% lower than the value of comparable models from previous generations, making a significant contribution to environmental protection. OperationThe operator panel is located on the top side of the housing and offers various options:Setting target moisture The desired target humidity can be set with each button press, which is the value that the device should maintain in the room. If the measured humidity in the room is higher, the operation continues. If the humidity is correct, the device pauses, stopping not only the compressor but also the fan. The desired target humidity can be selected in 5% increments between 30 - 90%, with the setting at 30% corresponding to continuous operation. To protect a room from mold and odors, a value of about 60% is sufficient, so the ideal setting is 50 or 55%. Lower values do not provide any additional benefit unless drying laundry or addressing water damage.   Fan speed settingBy pressing a button, you can choose between three ventilation levels. At the low fan setting, the operation becomes quieter, while at the medium and highest fan settings, the air volume increases significantly, which is especially advantageous in larger rooms and during laundry drying. The humid room air is drawn in from the back of the device, where it is cleaned by a removable coarse dust filter. The filter can be easily removed and cleaned under water. It does not need to be replaced. The exhaust of the dry air is located at the top of the device.   TimerWith the timer, the operation can either be limited in time "from now" (1-12 hours) or started at a point in time 1-12 hours in the future, for example, when one wants to start the operation at the low tariff.    Memory function"If you want to run the device at the same times every day (for example, during the low tariff), you can do this with a standard timer. The dryer remembers the last setting and returns with unchanged settings after a power interruption."     WLANIn addition to the operation on the device itself, all models of the "Royal" series are equipped with WIFI control. The app used for this, "Smart Life," can be downloaded for free for iOS and Android. The "Smart Life" app is very simple and user-friendly. It has been in circulation for a variety of household appliances for some time and is therefore well-developed and tested. To use the app, the dehumidifier only needs to connect to the WLAN in the house. The initial setup of the app takes only a few minutes. Once set up, you can monitor, regulate, and also query real-time information about the current humidity in the room from anywhere in the world via your mobile phone. This is very convenient while traveling abroad as well as for use in holiday homes.     Automatic Reminder Filter Cleaning "After 250 operating hours, the indicator light will illuminate to remind you to clean the filter. Remove the filter and clean it. Press the indicator light to turn it off."  Advantages and Features   • Dehumidification capacity of up to 60 liters per day (at a constant 30°C/80% r.H.), suitable for rooms up to a maximum of 150m²• Can also be controlled via Wi-Fi • 12-hour timer available for setting operating time• Economical operation measured by the dehumidification performance• Fan with three speed settings• Automatic self-defrosting at low room temperature• Auto mode: Shutdown / restart automatically depending on room humidity• Electronic control• larger 7.9 L water tank with viewing window and float (automatically interrupts when full), inserted at the front of the device• Direct hose connection (suitable hose has an inner diameter of 12mm)• Memory function, Smart Home capable• "GS" tested and CE certified dehumidification performanceThe dryer can be used over a wide temperature range between +5°C and +32°C, with the dehumidifying power decreasing in cooler environments, as is the case with all condensation dryers. Examples of the approximate dehumidification performance under different (constant) ambient conditions:   30 °C: 80 % humidity: 60 liters / 24 hrs. - 60 % humidity: 35 liters / 24 hrs.20 °C: 80 % humidity: 31 liters / 24 hours - 60 % humidity: 19 liters / 24 hours. 15 °C: 80 % humidity: 25 liters / 24 hrs - 60 % humidity: 15 liters / 24 hrs. 10 °C: 80 % humidity: 16 liters / 24 hrs - 60 % humidity: 11 liters / 24 hrs. 5 °C: 80 % humidity: 14 liters / 24 hours - 60 % humidity: 9 liters / 24 hours.     Technical data  Tension 220V-240V / 50Hz Power consumption 629 W (at 20°C/60% r.H.), max. 930 W / 3.9A Operating noise1 m distance2.5 m distance Min./Max. room size 10 / 150 m² dehumidification performance max. 60 liters/day (30°C / 80% r.H.)  Condensation tank Approx. 7.9 Liters   Compressor Rotary compressor  refrigerant R290, 185g Dimensions (H x W x D) 610 x 384 x 280 mm Weight 19.9 Kg Operational cessation Digital  Ambient temperature 5°C ~ 32°C  Area of application Basement, Hobby Room, Storage, Archive, Laundry Drying Swiss plug EU plug with Swiss fixed adapter, 1.5m cable hose connection Yes, suitable hose: 12mm inner diameter GWP (Global Warming Potential) 3 Guarantee 2 years Documents / Downloads   Operating Instructions German

Learn more More Fewer

A good, affordable racing horse for builders and water damage restorers. This dehumidifier has consistently omitted everything that is unnecessary for continuous operation. It has neither a display nor a hygrostat (a plug-in hygrostat can be optionally ordered if needed). This makes it very easy to operate, safe from tampering, and exceptionally low in price. On the other hand, it has everything needed for effective and quick drying: powerful dehumidification performance, hot gas defrosting, hour counter, as well as large wheels and a handle for easy mobility on construction and damage sites.     Easy handling   "The commissioning is child's play. Plug in - flip the main switch - done!"   The operation continues until either the bucket is full or the dryer is uninstalled again. As long as the device is connected to the power supply, it runs reliably and there are no settings that can be accidentally changed or manipulated. This also applies in the event of a power outage: when the power returns, the dehumidifier resumes its task with unchanged settings.   Thanks to the professional hot gas automatic control, operation in cooler environments is also possible without any issues, although the dehumidifying power, as with all condensation dryers, decreases at low temperatures. The installed finned evaporator (cooling element) has an exceptionally high efficiency in tempered environments and can dry the air to just below 40% relative humidity. Furthermore, the dryer is equipped with a rolling piston compressor. This means that it can be transported and stored in any position.     Optional Hygrostat   "Should a hygrometer for regulating the target humidity be required at any point, the dryer is prepared so that the Trotec Hygrostat HG110 can be connected directly via a jack plug. Please note the accessories."     Bucket and direct hose connection   The water extracted from the air is collected in a bucket with a capacity of 5 liters. A magnetic float automatically interrupts operation when full, and a warning light visually indicates that the bucket should be emptied. A hose can be connected to the bucket if needed, in case the water can be drained directly. The hose must be laid downwards, as no pump is integrated in the dryer.     Suitable for unattended continuous operation   This "TTK" is suitable for longer, unattended drying operations. The exact operating time can be precisely determined with the standard integrated hour meter. This is particularly useful for commercial applications. Thanks to the meter, it can also be tracked whether the device was always in operation or if it was accidentally or intentionally turned off.     Propane (R290) as an environmentally friendly refrigerant in dehumidifiers   "Every year, several million tons of environmentally harmful CO2 emissions (greenhouse gases) are released into the air due to synthetic refrigerants. Therefore, the use of alternative refrigerants is one of our most important goals. By using propane (R290) as a refrigerant, this dehumidifier makes a valuable contribution to climate protection."   The natural refrigerant propane (R290) is an organic compound and belongs to the hydrocarbons. Unlike synthetic refrigerants, environmentally friendly propane (R290) has neither ozone depletion potential (ODP=0) nor a significant greenhouse effect (GWP=3).   Supplement plus for the environment: Due to its excellent thermodynamic properties, propane (R290) is a particularly energy-efficient refrigerant, thereby additionally reducing your energy costs.     Advantages at a Glance   • Affordable price with strong performance in the commercial sector• Thanks to hot gas defrosting, it can also be used in cooler environments.• Robust steel construction with large wheels and guide bracket• Suitable for continuous operation• Thanks to the roll piston compressor, it is transportable and storable in any position.• External hygrometer connection     Technical data  dehumidification performance at 30 °C / 80 % r.H. 50 liters / day air volume 350 m³/ h Maximum room size 125 m² (310 m³) Minimum room size 8 m² (30 m³) temperature range 5 - 32°C Moisture range technical Moisture Range Practice 35 - 90 % r.F. 40 - 90 % r.H. (lamella evaporator) Voltage 220 - 240 V/50 Hz rated current consumption max. 3.7 A Power consumption max. 820W Recommended Coverage 10 A Cable length approx. 2 m Plug EU plug with Swiss adapter refrigerant R290 (230g) GWP3 water bucket 5 Liter operating noise 56 dB(A) at 1 m distance 53 dB(A) at a distance of 2.5 m Dimensions L x W x H 495 x 455 x 900 mm Weight 31 kg defrosting automatic Heissgas dehumidification automation Continuous operation, an insertable mechanical hygrometer is optionally available. Ventilator axial, single-stage blower automatic shut-off when bucket is full and prefilter and operating hour meter and Continuous operation possible and Display no memory function yes (automatically saves set values) hose connection yes, not included in the delivery (suitable inner diameter: 12 mm) guarantee 2 years Documents / Downloads   User Manual German   User manual French   User manual Italian   User manual English

Learn more More Fewer

Commercial Dehumidifier TROTEC TTK 166 ECO Efficient dehumidification – with the TROTEC TTK 166 ECO: robust commercial dehumidifier with up to 50 l/24 h dehumidification capacity, controllable via hygrostat and timer. Ideal for construction sites, warehouses and commercial premises – durable steel construction, mobility thanks to trolley design and environmentally friendly R290 refrigerant. The perfect choice for reliable humidity regulation in commercial applications. The TROTEC TTK 166 ECO is a powerful commercial dehumidifier specifically designed for continuous use in commercial and industrial environments. With a maximum dehumidification capacity of up to 50 litres per 24 hours under optimal conditions, this device impresses with its efficiency and economy. Features: Robust steel housing and trolley design Large digital display for humidity & temperature Adjustable target humidity (10 % to 95 % r.H.) Timer function for switch-on and switch-off times Environmentally friendly R290 (propane) refrigerant 7-litre water tank & optional condensate drain Memory function after short power failure Features & Details Robust steel housing and trolley design with carrying handle and large wheels – ideal for use on construction sites or in harsh environments. Large digital display shows both the current room humidity and room temperature – in standby mode and during operation. Adjustable target humidity in 1-percent increments from 10 % to 95 % r.H. via integrated hygrostat – for optimal humidity control. Timer function with pre-selection of switch-on and switch-off times – for automated dehumidification. 7-litre water tank and optional external condensate drain or condensate pump – suitable for unsupervised drying operations. Memory function: The device saves the last set target humidity in case of a short power failure and starts automatically when power returns. Environmentally friendly refrigerant Environmentally friendly R290 (propane) refrigerant with an ozone depletion potential = 0 (ODP = 0) and a low global warming potential (GWP = 3) – reduces energy costs and protects the environment. Features & Functions at a Glance Robust steel housing and trolley design with carrying handle and large wheels – ideal for use on construction sites or in harsh environments. Large digital display shows both the current room humidity and room temperature – in standby mode and during operation. Adjustable target humidity in 1-percent increments from 10 % to 95 % r.H. via integrated hygrostat – for optimal humidity control. Timer function with pre-selection of switch-on and switch-off times – for automated dehumidification. Environmentally friendly R290 (propane) refrigerant with an ozone depletion potential = 0 (ODP = 0) and a low global warming potential (GWP = 3) – reduces energy costs and protects the environment. 7-litre water tank and optional external condensate drain or condensate pump – suitable for unsupervised drying operations. Memory function: The device saves the last set target humidity in case of a short power failure and starts automatically when power returns. Technical Data General Information Trotec item no. 1120001116 Dehumidification capacity 50 l/24h at 30 °C/80 % r.h. Recommended room size 90 m² / 230 m³ Air volume max. 300 m³/h Electrical Values Power consumption 950 W Mains connection 220 - 240 V, 50 HzMains cable with EU plug plus fixed adapter for Switzerland Rated current consumption 4 A Recommended fuse protection 10 A Refrigerant Refrigerant type R290 (Propane) Refrigerant quantity 200 g GWP factor 3 CO2 equivalent 0.0006 t Dimensions & Weight Dimensions (L x W x H) without packaging 480 x 450 x 655 mm Weight without packaging 30 kg Functions & Features Water tank capacity 7 litres Automatic defrost Circulating air, electronic Hygrostat Integrated (10% - 95% r.h.) Protection class IP22 Mobility Trolley, transport handle, cable winding Warranty 2 years

Learn more More Fewer

Powerful air dehumidifier / construction dryer 50B-WDH with calibrated consumption meter.The "50B" has been specifically designed to quickly dry water damage, e.g. after flooding or inundations. It features a very strong dehumidification performance and only has a power switch for optimal operation on construction sites and during water damage drying. A hygrometer for regulating the target humidity has been deliberately omitted in this version. Recommended room size up to 120m², from 8°C. The performance and drying speed can be additionally accelerated with free-standing fans if needed (e.g. FN45 from our range).Characteristics • Dehumidification capacity of up to 42 liters / day (at 30°C/80% r.H.)• Function for continuous operation/continuous dehumidification• calibrated consumption meter (kWh)• On/Off toggle switch• Equipped with a highly efficient rotary compressor. This compressor is one of the most powerful compressors on the market.• Automatic professional defrost function• Removable condensate tank• Connection possibility of a hose for continuous drainage of the condensate• Powder-coated metal housing/metal frame• Very easy mobility due to transport handles and large running wheels for safe travel over steps and uneven ground.• Operating warning light / Defrost light• No separate or additional coolant is required (closed circuit)• Washable air filter grid• Environmentally friendly refrigerant R290• CFC free and compliance with WEEE standards ImportantThe construction dryer "50B" is not suitable for use in very cold rooms, as it can freeze during continuous operation below 8°C due to the powerful dehumidification unit.   dehumidification performanceThe dryer is via a Temperature range from +8°C to +32°C is applicable, whereby, as with all condensation dryers, the dehumidifying power decreases in cooler environments. Examples of dehumidification performance and consumption under various (constant) ambient conditions:30°C/80% r.H.: approx. 42 liters (at 60% r.H.: approx. 21 liters)20°C/80% r.H.: approx. 21 liters (at 60% r.H.: approx. 12 liters)15°C/80% r.H.: approx. 15 liters (at 60% r.H.: approx. 8 liters)10°C/80% r.H.: approx. 8 liters (at 60% r.H.: approx. 6 liters)(r.H.=relative humidity)Technical data  Tension 220-240V / 50Hz Power consumption: max. 820 (3.7 A) or 620W (at 20°C/60% r.H.) Sound pressure level: 57 dB(A) (Manufacturer's specification) dehumidification performance 42 liters/day (30°C / 80% r.H.)  amount of recirculated air 400 m³/h (installed) condensate tank approx. 5 liters (direct hose connection possible) Compressor Rotary compressor  refrigerant R290 (230gr.) Dimensions (H x W x D)  890 x 450 x 740 mm Weight 32 Kg cessation of operations ON/OFF toggle switch Ambient temperature 8°C ~ 32°C Area of application Rooms from min. 10m² to max. 120m² Swiss plug: EU plug with fixed adapter for Switzerland  hose connection Yes guarantee 2 years

Learn more More Fewer

The Oasis dehumidifiers are among the widely used drying devices that have been successfully employed on construction sites and by private users for many years. The devices have now been revised and adapted to the latest state of technology with the newest environmentally friendly refrigerant R290 and improved efficiency. The Oasis D165 is suitable for basements and rooms up to 90m² and comes standard with a large bucket as well as a direct hose connection.Although visually very similar, the D165 dehumidifier has been completely revised in various respects compared to its predecessor:• improved efficiency• higher dehumidification performance• environmentally friendly refrigerant R290• improved automatic self-defrosting, thus usable down to 5°C (previously: 8°C)• reinforced front cover with spark guard bowl• reinforced, load-bearing wheelsThe dryer stands on 4 wheels but can also be mounted on a suitable wall bracket available from us if desired. The air intake area is at the back, where a filter cleans the moist air. The filter itself is easy to remove and clean. The dry air is blown out towards the front into the room. The Oasis is therefore ideal for general moisture control in a classic basement environment, for example in new buildings, but also for unattended continuous operation in temperature-controlled archives and on construction sites. For active laundry drying, the blower is rather too weak.The target humidity is regulated via a stepless hygrostat on the front. Once the set value is reached, the dehumidification operation pauses (the ventilation also stops) until the humidity rises again. The operation continues with the unchanged setting even after a power interruption. The D165 is therefore also suitable for operation with a timer, if you want to run the dryer, for example, only during off-peak hours. Thanks to the pipe evaporators, the D165 extracts water from the air even in low humidity ranges.The water is collected in the tank pushed in at the back, a float mechanically interrupts operation when full. Alternatively, a hose can be screwed onto the condensate collection tray (with a coupling / 3/4-inch thread), with the hose needing to have a slope towards the drain (no pump integrated in the device).usage examplesCellar Moisture: Ideal for damp cellars, old walls, and laundry rooms. Eliminates musty odors, stops mold growth, decomposition of masonry, and much more.Construction and Industrial Dryers: thanks to their handy, robust design, they are ideally suited for drying on construction sites and in the industry.Drying of Water Damage: The Oasis removes water from the air even in deep moisture areas through the pipe evaporators. This significantly accelerates the drying of water damage.dehumidification performanceThe dryer can be used thanks to hot gas defrosting over a wide temperature range from +5°C to +32°C, although, as with all condensation dryers, the dehumidifying power decreases in cooler environments. Examples of dehumidification performance and consumption under various (constant) environmental conditions:  30°C/80% r.H.: 28 liters / 24 h27°C/60% r.H.: 16.8 Liters / 24 h20°C/60% r.H.: 10.8 Liters / 24 h10°C/70% r.H.: 5.3 Liters / 24 h(r.H.=relative humidity)    Massive improvement regarding environmental compatibilityThe GWP (Global Warming Potential - impact on global warming) could be reduced by a factor of 800 (!) from 1430 (R134a) to less than 2 (R290). Furthermore, the D165 requires 10% less electricity while simultaneously increasing dehumidification performance by 14% (at room temperature 20°C, 60% r.H.). Technical data  Tension 230V / 50Hz Power consumption max. 360W Sound pressure level 1 m distance 54 dB(A) (our measurement) 2.5 m distance 51 dB(A) (our measurement) dehumidification performance max. 28 liters/day (30°C / 80% r.H.)  Bucket Capacity 9 liters, approx. 8 liters until operation interruption by float Compressor Rotary compressor  refrigerant R290 (150gr.) Dimensions (H x W x D)   60 x 38 x 36 cm (incl. wheels) Weight 23.5 Kg cessation of operations Hygrostatrad   Ambient temperature 5°C ~ 40°C  Area of application about 90m² Swiss plug Yes   hose connection Yes operating hour meter Yes guarantee 2 years    

Learn more More Fewer

This construction dryer is very popular in professional use because it has a strong dehumidification performance of up to 30 liters per day and, at less than 20 kg, is considered one of the lightweight models in this category of dehumidifiers. This means that it can be easily transported by one person up stairs and even over scaffolding to the drying location. Furthermore, it is compact in dimensions, which saves space in the service vehicle. This is highly appreciated by water damage restorers who need to bring many devices to the damage site in the shortest possible time. This model also impresses during storage, as it is stackable and therefore takes up less space in the warehouse.  Operation 'The digital control panel at the top of the device allows you to select the desired target humidity in 1% increments. Continuous operation is also possible. By pressing the memory button, the set values are saved. This way, in the event of a power interruption, operation will automatically continue with unchanged settings as soon as the power supply is restored. A side-mounted operating hour meter provides information about the drying duration.' The humid room air is drawn in from the back and cleaned of dust and dirt through an easily cleanable filter. The dried air is then blown out from the front. The automatic hot gas defrosting ensures that dehumidification occurs with maximum efficiency even in cooler environments. The water extracted from the air can be collected in the inserted bucket or drained directly through a hose (suitable inner diameter: 10 mm). A float automatically interrupts operation when the bucket is full. If the water is drained through the hose, it first passes through the bucket to which the hose connector is attached. This system is very safe: if the hose is clogged, kinked, or not properly laid, the water backs up into the bucket. When the bucket is full, operation stops. Overflow onto the floor is therefore not possible, unlike dryers where the hose is directly attached to the drip tray.  Important functions • Digital control and side-mounted operating hour meter• High efficiency thanks to automatic hot gas defrosting• Robust housing with a foldable carrying handle and four small wheels• Easy operation• Built-in hygrometer• Water tank with automatic shut-off when full• Possibility to connect a hose for direct drainage of condensate• Air filter• Stackable   Suitable for • Drying of private cellars and rooms• Drying of commercial spaces and archives• Construction• Industry and Production• Rental• Construction and water damage drying• Waterworks  Propane (R290) as an environmentally friendly refrigerant in dehumidifiers"Every year, several million tons of environmentally harmful CO2 emissions (greenhouse gases) are released into the air due to synthetic refrigerants. Therefore, the use of alternative refrigerants is one of our most important goals. By using propane (R290) as a refrigerant, this dehumidifier makes a valuable contribution to climate protection." The natural refrigerant propane (R290) is an organic compound and belongs to the hydrocarbons. Unlike synthetic refrigerants, environmentally friendly propane (R290) has neither ozone depletion potential (ODP=0) nor a significant greenhouse effect (GWP=3). "Supplement plus for the environment: Due to its excellent thermodynamic properties, propane (R290) is a particularly energy-efficient refrigerant, thereby additionally reducing your energy costs."   Technical data  dehumidification performance at 20 °C / 60 % r.H. at 30 °C / 80 % r.H.   10.8 liters / day 30 liters / day air volume max. 200 m³/ h Maximum room size 75 m² (180 m³) temperature range 5 - 35 °C Moisture range technical  Moisture Range Practice 35 - 90 % r.F. 40 - 90 % r.H. (lamella evaporator) Voltage 220 - 240 V/50 Hz rated current consumption max. 3 A Power consumption max. 680 W Recommended Coverage 10 A Plug Connection cable with EU plug and Swiss fixed adapter refrigerant R290 (GWP: 3) Bucket + Hose connection 6.5 liter bucket and direct hose connection (suitable hose 10mm inner diameter) operating noise 45 dB(A) at 1 m distance 42 dB(A) at a distance of 3 m Masse (B x H x T) 338 x 550 x 358 mm Weight 19.5 kg Automatic defrosting Heissgas Attitude Digital Operator Panel Ventilator axial, single-stage blower Compressor rolling piston prefilter and operating hour meter and Continuous operation possible and Display and memory function yes (set values saved on button press) guarantee 2 years

Learn more More Fewer

The universal all-rounder   "Whether for drying out after water damage, new building drying, or maintaining dry conditions in heated and unheated storage rooms - the 170S is a universally applicable dehumidifier with high-quality workmanship and reliable operation. It is manufactured in a specialized plant in Europe. It is built to last, easy to maintain, rarely needs servicing, and is very affordable considering its power and quality.".     Easy handling   "Using a mechanical hygrometer, the desired target humidity can be continuously adjusted between 32 - 100%, and continuous operation is also possible. Particularly useful in larger areas is the high air circulation volume of a substantial 580 cubic meters per hour. With its stable cart construction and large wheels, frequent relocation to different usage sites can be easily carried out."     Bucket, direct hose connection and optional pump kit   The water, which is extracted from the air, flows into the 6-liter bucket. This is placed on a scale that automatically interrupts operation when full. A control light indicates the full status in this case. Furthermore, there is the possibility to connect a hose if the water can be drained directly. The hose must have a slope towards the drain in this case. If this is not possible, a suitable pump kit is optionally available, with which the water can be pumped upwards and also outwards.   "The operating switch and level warning light are protected against dust and splashing water by a protective cover, and a slotted hygrostat rotary switch prevents unwanted adjustment of the switch position."     Professional Hot Gas Defrosting   Inside, a professional hot gas defrosting automatic system ensures effective dehumidification results. The fin evaporators unleash their power particularly in temperature ranges above 10°C and in areas above 40% humidity. Technically, the dryer can also be used in lower ranges down to about 5°C, even in unattended continuous operation.     Optional counters   The delivery includes no "Hour or consumption meters are included. You can order them from us upon request (the housing is standardly prepared for retrofitting). You have the choice between a pure hour meter or the combined dual meter, which measures hours and electricity consumption. The meters are MID compliant. Outside of Switzerland, dryers in professional use must already be MID compliant."     Propane (R290) as an environmentally friendly refrigerant in dehumidifiers   Annually, several million tons of environmentally harmful CO2 emissions (greenhouse gases) are released into the air due to synthetic refrigerants. Therefore, the use of alternative refrigerants is one of our most important goals. By using propane (R290) as a refrigerant, this dehumidifier makes a valuable contribution to climate protection. The natural refrigerant propane (R290) is an organic compound and belongs to the hydrocarbons. Unlike synthetic refrigerants, environmentally friendly propane (R290) has neither ozone depletion potential (ODP=0) nor a significant greenhouse effect (GWP=3).   Supplement Plus for the Environment: Due to its excellent thermodynamic properties, propane (R290) is a particularly energy-efficient refrigerant, thereby additionally reducing your energy costs.     Advantages at a Glance   • High dehumidification performance even at low temperatures• Robust plastic-coated metal housing• Thanks to the roll piston compressor, it is transportable and storable in any position.• Stable carriage construction• Automatic hygrostat-controlled dehumidification operation• Quality hot gas defrost automatic system• Option to retrofit MID-compliant dual meter for operating and kilowatt hours (optional) • Option to add a suitable pump kit that can be connected directly to the device (optional)   Technical data  dehumidification performance at 30 °C / 80 % r.H. 40 liters / day air volume 580 m³/ h Maximum room size 100 m² (250 m³) Minimum room size 8 m² (20 m³) temperature range 5 - 32°C Moisture range technical Moisture Range Practice 32 - 90 % r.F. 40 - 90 % r.F. Voltage 220 - 240 V/50 Hz rated current consumption max. 2.8 A Power consumption max. 600W Recommended Coverage 10 A Cable length approx. 3 m Plug EU plug with Swiss adapter refrigerant R290 (150g) GWP3 water bucket 6 Liter operating noise 52 dB(A) at 1 m distance 49 dB(A) at a distance of 2.5 m Dimensions L x W x H 540 x 490 x 963 mm (incl. guide bracket) Weight 32 kg defrosting automatic Heissgas dehumidification automation Hygrostatgesteuert Ventilator axial, single-stage blower automatic shut-off when bucket is full and prefilter and Timer no (operation on timer possible) Continuous operation possible and memory function yes (mechanically stores set values) hose connection yes (no hose included in the delivery) - 12 mm Pump optional available (not included in the scope of delivery) guarantee 2 years

Learn more More Fewer

A carefully crafted, reliable dehumidifier for construction sites and drying water damage. Due to its advantages, it is often used in private settings to keep damp basements and garages dry. Good mobility thanks to the handle and two large wheels.The AD432F is the further development of the AD430F. It is more compact, lighter, and more economical than its predecessor. A tube evaporator replaces the previous finned cooling element. As a result, the dryer is less susceptible to contamination and has better dehumidification performance at lower temperatures and lower humidity.Unlike conventional dehumidifiers in this category, the device has a scale instead of a float in the bucket for precise shut-off as soon as the bucket is full. There is also a hose connection for direct drainage of the condensate. An optional addition is a condensate pump, which can be conveniently hung in the bucket and connected directly to the dryer.The housing is made of coated sheet steel in a high-quality stainless steel look. When the desired target humidity is reached, the device completely shuts off. The built-in operating hour counter clearly and quickly shows how long the device has been in use.  Characteristics• Housing: Steel sheet coated in stainless steel look.• Setup: Rack and two large wheels for equally good stability and mobility.• Airflow: Air intake rear / Air outlet front.• Air filter: Protects the device from dust.• Operating hour meter• Fan: reliable axial fan.• Condensate drain: Water tank 8 liters with automatic shut-off when full, hose connection.• Pump Kit: Flexibly usable pump kit for permanent condensate drainage (accessory).• Memory Function: After a power interruption, it resumes operation with unchanged settings. Therefore, it is also suitable for operation with, for example, a timer. • Hot gas defrosting: Thanks to automatic self-defrosting, it can also be used in cooler environments.• Suitable for unattended continuous operation • Made in Europe/Portugal     dehumidification performanceThe dryer can be used over a wide temperature range from +3°C to +32°C thanks to its advanced hot gas defrosting, although, as with all condensation dryers, the dehumidifying power decreases in cooler environments. Examples of dehumidification performance and consumption under various (constant) environmental conditions:30°C / 80% r.H.: 28.0 Liters / 24 h27°C / 60% r.H.: 16.5 liters / 24 h20°C / 60% r.H.: 12.1 liters / 24 h(r.H.=relative humidity)   latest technologyThe 432F features the latest technology. The pipe evaporators extract water from the air even when conventional dehumidifiers have long stopped producing a drop. The latest refrigerant R290 is almost climate-neutral and has improved efficiency.   Technical data  Tension 230V / 50Hz Power consumption max. 600W / 430W (at 20°C/60% r.H.) Sound pressure level 1 m distance 51 dB(A) (our measurement) 2.5 m distance 55 dB(A) (our measurement) dehumidification performance 28 liters/day (30°C / 80% r.H.) amount of recirculated air 250 m³/h installed (free-blowing: 550 m³/h) condensate tank Approx. 8 liters Compressor Rotary compressor refrigerant R290 Dimensions (H/W/D) 54 x 34 x 39.5 cm 78 x 44 x 54 cm with rack/wheels Weight 28 Kg cessation of operations Hygrostatrad Ambient temperature 3°C ~ 32°C Area of application up to 90m² (tempered rooms) resp. 70 m² (unheated rooms) Swiss plug Yes hose connection Yes operating hour meter Yes Guarantee: 2 years

Learn more More Fewer

High-quality profit dryer, specifically developed by us for the needs in water damage drying. Ideal for sanitary and drying companies, but also suitable for construction and industry.  Robust construction The new AD432R is a variation of the popular AD432F. The housing is made of robust metal, and the internal components are designed to withstand frequent transport or rough handling. Two side grip recesses and 4 heavy-duty rubber wheels (2 of which have brakes) facilitate quick and space-saving loading and unloading into emergency vehicles. As a practical addition, there is a socket on the side of the housing for connecting, for example, an additional ventilation.  Bucket or Pump Operation The standard delivery includes a large bucket as well as a direct hose connection for draining the water. The bucket is placed on a scale that automatically interrupts operation when full. Additionally, there is a connection box behind the bucket for a suitable condensate pump. The power supply for the pump is therefore provided by the device itself. Since the pump and dryer are connected in this way, the dryer stops in the event of a defective pump. The pump is optional and available from us.   latest technologyThe 432R features the latest technology. The pipe evaporators extract water from the air even when conventional dehumidifiers have long stopped producing a drop. The latest refrigerant R290 is almost climate-neutral and has improved efficiency. The AD432R is suitable• as a dryer in case of water damage• as a construction dryer• for the drying of archives, basements, and commercial spaces up to 90m²• for unattended continuous operation• for operation on a timer  dehumidification performanceOverview of the approximate dehumidification amounts in liters per day at different room temperatures and humidity levels:30°C/80% r.H.: 28 Liters27°C/60% r.H.: 16.5 Liters20°C/60% r.H.: 12.1 Liters(r.H.=relative humidity)  Replacement air filters for the AD432R are available from us at any time for CHF 32.30 per 5-pack. The 432R is manufactured in a specialized plant in Europe - no Chinese products.   Technical data  Tension 230V / 50Hz Power consumption max. 600W / 430W (at 20°C/60% r.H.) Sound pressure level 1 m distance 51 dB(A) (our measurement) 2.5 m distance 55 dB(A) (our measurement) dehumidification performance 28 liters/day (30°C / 80% r.H.) amount of recirculated air 250 m³/h (installed) 550 m³/h (free-blowing) condensate tank Approx. 8 liters Compressor Rotary compressor refrigerant R290 Dimensions (H x W x D) 60 x 37 x 38 cm Weight 32 Kg cessation of operations Hygrostatrad Ambient temperature   5°C ~ 32°C Area of application up to 90m² (tempered rooms) resp. 70 m² (unheated) 40% r.H. - 95% r.H. Swiss plug Yes hose connection Yes operating hour meter Yes Housing Metal, powder-coated RAL 5017 (Traffic Blue) guarantee 2 years

Learn more More Fewer

The top dryer for medium-sized rooms and for rooms with high humidity levels. The FDK provides reliable dehumidification work in both cooler and temperate rooms.The operation is incredibly simple: a rotary knob for adjusting the desired target humidity and that's it. Everything else is done automatically by the device. For example, the FDK can utilize its dehumidifying power for year-round dry storage of single or double garages, archive rooms, basement areas, or also for stabilizing humidity in laundry and drying rooms. You can only get this model from us; comparable products on the market are significantly more expensive.Due to well-developed hot gas defrosting, the dryer is operational down to just above freezing point. Also very noticeable is its good performance in low humidity ranges, where it still extracts water from the air, while other dryers have long stopped producing any drops. Upon reaching the desired target humidity, the device completely shuts off and automatically restarts when the room humidity increases.The humid air is drawn in on one side of the housing and cleaned through an industrial, reusable filter. The dry air is blown into the room from the opposite side, creating an effective circulation in the room. Regarding placement in the room, many locations are conceivable. Both at floor level, somewhere on a free shelf, or mounted to the wall with brackets. When wall-mounted, the dryer can also be installed high up directly under the ceiling.The condensate is drained directly through the hose connection. The FDK44 stands on 4 (removable) rubber feet and has two foldable carrying handles on the top of the housing for easier mobility. When positioned close to the ground, the hose must have a continuous slope towards the drain so that it can drain cleanly and does not back up into the collection tray.The construction is solid and of high quality. The housing is made of white powder-coated metal, and the interior consists of components from the professional league. Therefore, the device is easily suitable for unattended continuous operation. In the event of a power failure, it resumes the dehumidification work with unchanged settings, making it suitable for operation with a timer or a smart home system.The FDK is suitable• as a dehumidifier for warehouses, commercial and industrial spaces, garages, and basements• for wall mounting or directly on the ceiling• for continuous dehumidification of temperate but also cold rooms from 1°C• for unattended continuous operation• for operation on a timer     dehumidification performanceThe dryer can be used over a wide temperature range from +1°C to +35°C thanks to its advanced hot gas defrosting, although, as with all condensation dryers, the dehumidifying power decreases in cooler environments. Examples of dehumidification performance under different (constant) ambient conditions:30°C/80% r.H.: 36 Liters20°C/80% r.H.: 18 Liters20°C/60% r.H.: 14 Liters10°C/60% r.H.: 8 Liters(r.H.=relative humidity) Optional accessoriesThe delivery includes the ready-to-plug-in device, including 4 stand feet for placement, e.g., on a shelf. If needed, we offer various suitable accessories for this dryer, such as:• 2 wall consoles for mounting on a wall (total Fr. 68.-)• Hose coupling• Hose• Condensate pump (if the condensate needs to be pumped upwards)Stronger versionThe device is also available in double strength as "FDK100" -> DetailsComparable devices: Lunor L25     Technical data  Model: Fral Horizon FDK44 Tension: 230V / 50Hz Power consumption:  max. 780W / 530W (at 20°C/60% r.H.) Sound pressure level:  (our measurement) 1 m distance 53 dB(A) 2.5 m distance 51 dB(A) Dehumidification capacity: 36 liters/day (30°C / 80% r.H.)  air circulation volume: 450 m³/h (installed, free-blowing approx. 650 m³) condensate tank: No tank / only hose connection possible Compressor:     Rotary compressor  refrigerant:   R410A (650gr.) Dimensions (L/H/D):      58 x 44 x 36 cm (including feet and carrying handles) Height without feet and carrying handles: 37 cm Weight:    34 Kg Business closure: Hygrostatrad Ambient temperature: 1°C ~ 35°C  Application area: up to 100m² Swiss plug:  Yes   hose connection:  Yes Guarantee: 2 years

Learn more More Fewer

Compact Professional Construction Dryer with Integrated Condensate Pump for Construction and Water Damage Restoration Powerful, compact and robust dehumidifier for continuous professional use – ideal for construction drying, water damage, renovations and mold remediation in demanding environments. This compact professional construction dryer was specially developed for daily use on construction sites, in water damage remediation, and for renovation and drying work. With its high dehumidification capacity of 21 liters per day, it reliably ensures dry rooms and effectively prevents mold formation and moisture damage. The robust housing made of resistant plastic reliably protects the device from dust, dirt and mechanical stress in everyday construction. This makes the dehumidifier ideal for professional use under harsh conditions. Thanks to the powerful rotary compressor, the device works efficiently immediately even after transport or storage. The integrated condensate pump enables almost maintenance-free continuous operation, as the accumulating water is automatically drained – ideal for unattended drying operations. Due to its compact design, low weight and stackability, this construction dryer is particularly flexible to use and easy to transport. It is suitable for professional remediation companies as well as for craft businesses and rental fleets. Your advantages: 21 L/day dehumidification capacity Integrated condensate pump for continuous operation Very compact and robust design Ideal for water damage and new construction Rotary compressor for immediate operation Stackable and easy to transport Resistant housing for construction sites Simple plug-and-play operation Optional external hygrostat can be connected Exhaust air can be ducted via hose Low energy consumption Suitable for unattended use Efficient Construction Drying and Water Damage Restoration The construction dryer was designed for the rapid reduction of construction and residual moisture. It significantly accelerates drying processes after water damage, burst pipes or new construction work and ensures a stable, dry indoor climate. Through even air circulation, moisture is efficiently removed from the room, reliably preventing subsequent problems such as mold growth, material warping or structural damage. Simple Operation and Automated Performance Commissioning follows the proven plug-and-play principle: set up, switch on, and the drying process starts automatically. The desired humidity can be conveniently set. Thanks to the integrated control, the device operates fully automatically and continuously adapts its performance to the room conditions. This ensures constant and efficient dehumidification. Integrated Condensate Pump for Maintenance-Free Continuous Operation The built-in condensate pump enables direct drainage of the accumulated water. This eliminates the need for manual emptying of a container, which is a great advantage, especially for long or unattended drying operations. The device can therefore be operated continuously for long periods without the need for regular maintenance. Robust, Compact and Developed for Everyday Construction Use The sturdy plastic housing reliably protects the technology from external influences. At the same time, the compact design ensures that the construction dryer can be easily transported, stored and stacked. These features make it particularly suitable for mobile use in the construction and renovation industry. Flexible Applications and Extensions For special requirements, an external hygrostat can be connected to control humidity even more precisely. Additionally, an exhaust air hose is possible for targeted air guidance. This allows the construction dryer to adapt flexibly to different operating conditions – from small renovation projects to large-scale construction drying. Technical Data Dehumidification capacity 21 Liters / 24h (30°C / 80% r.h.) Air flow rate 375 m³/h Temperature range 5 – 35 °C Humidity range 30 – 90 % r.h. Power consumption 380 W Connection cable 2 m with EU plug and fixed adapter for Switzerland Refrigerant R290 Sound pressure level approx. 60 dB(A) Water tank integrated, with condensate pump Compressor Rotary compressor Dimensions 360 × 330 × 490 mm Weight approx. 20–22 kg Warranty 2 years Information Videos

Learn more More Fewer

Professional construction dehumidifier with large bucket A high-quality dehumidifier for commercial use and water damage drying, manufactured in Europe. Its impressive exterior appearance is matched by its internal values: all electrical components are specially encapsulated, protecting the electronics from harmful deposits that could impair their function and longevity. Therefore, this dryer is also ideally suited for use under demanding conditions. Thanks to its maintenance-friendly design, it is easy to care for. "Compared to more affordable piston compressors, the high-quality 0.58 kW rotary compressor installed here offers the advantage of higher performance with comparatively lower power consumption – and additionally provides reserves for high dehumidification performance even in unheated rooms."In addition, the high-quality hot gas defrosting automatic system ensures a much more efficient dehumidification performance compared to other defrosting devices, without time interval-related defrosting pauses during which no dehumidification takes place.  Propane (R290) as an environmentally friendly refrigerant in dehumidifiers Annually, several million tons of environmentally harmful CO2 emissions (greenhouse gases) are released into the air due to synthetic refrigerants. Therefore, the use of alternative refrigerants is one of our most important goals. By using propane (R290) as a refrigerant, this air dehumidifier makes a valuable contribution to climate protection. The natural refrigerant propane (R290) is an organic compound and belongs to the hydrocarbons. Unlike synthetic refrigerants, environmentally friendly propane (R290) has neither ozone depletion potential (ODP=0) nor a significant greenhouse effect (GWP=3).  Supplement plus for the environment: Due to its excellent thermodynamic properties, propane (R290) is a particularly energy-efficient refrigerant, thereby additionally reducing your energy costs.  User-friendly Thanks to its durable housing, ergonomic grip recesses with an internal grip clip, and four sturdy wheels with a roll stop, the device is ideally suited for use on construction sites and for drying water damage. However, these advantages are also appreciated in commercial spaces or in private basement environments. The storage is also well thought out: two practical stacking grooves on the top of the device allow for a stable and space-saving stacking during transport and in storage.   An integrated operating hour meter reliably documents the exact duration of use even during longer drying operations.   Integrated compressor thermal protection with automatic shut-off   In drying operations with extremely high humidity and simultaneously high temperatures – for example, during water damage restoration – refrigerant dryers quickly enter their red performance zone. Here, the catchy "35 rule" applies: water damage above 35 degrees reduces the dryer’s lifespan to below 35%. However, this is not a question of component quality, but pure physics, which applies independently of the manufacturer to all refrigerant dryers on the market.  While most professional condensate dryers can still operate without issues at moderate humidity around 70% r.F. up to 35 °C, very high humidity combined with high room temperature results in significantly more energy being supplied to the humid air, which must be additionally "processed" through the refrigerant. Consequently, the pressure of the refrigerant in the system increases immensely, leading to a destructive load on the compressor. Although the dehumidifiers will initially continue to operate, they will do so well beyond their limit "deep in the dark red zone," resulting in an extremely shortened remaining lifespan.  "Therefore, the commercial dehumidifiers of the TTK-S series are equipped with an integrated compressor thermal protection for the active preservation of your devices:"Sensors continuously monitor the thermal load of the compressor. If the temperature is within the defined operating range, the integrated heat protection indicator pulses in a long sequence, indicating optimal operation of the dehumidifier. As soon as the temperature exceeds the critical threshold of 35 °C, the automatic system switches off the compressor to protect it, while the fan continues to operate, and automatically reactivates the compressor as soon as the 35° threshold is fallen below again. This protection not only significantly extends the lifespan of the dehumidifiers, but also prevents thermal damage to materials in the room and the building structure during their use.   Options • Dual meter available for additional recording of electricity consumption.• high-performance condensate pump for permanent drying with a pumping capacity of up to 50 m distance and a maximum delivery height of 4 m  Advantages at a Glance • High dehumidification performance even at low temperatures • Maximum dust and moisture protection for all electrical components• Extremely maintenance-friendly design • Optimal handling characteristics • Thanks to the roll piston compressor, it is transportable and storable in any position. • Practical stacking groove for stable, space-saving storage and transport • Multistage capability with identical models• Practice-oriented industrial design• Made in Europe  Technical data  dehumidification performance at 30 °C / 80 % r.H. 28 liters / day air volume 250 m³/ h Maximum room size 70 m² (175 m³) Minimum room size 8 m² (30 m³) temperature range 5 - 32°C moisture range 35 - 90 % r.F. Voltage 220 - 240 V/50 Hz rated current consumption max. 2.3 A Power consumption max. 500W Recommended Coverage 10 A Cable length approx. 3 m Plug EU plug with Swiss adapter refrigerant R290 (150g) GWP3 water bucket 6 Liter operating noise 52 dB(A) at 1 m distance 49 dB(A) at a distance of 2.5 m Dimensions L x W x H 375 x 345 x 603 mm Weight 26 kg defrosting automatic Heissgas dehumidification automation Hygrostatgesteuert Ventilator axial, single-stage blower automatic shut-off when bucket is full and prefilter and Timer no Continuous operation possible and memory function yes (mechanically stores set values) hose connection yes, short hose piece included in the delivery guarantee 2 years   

Learn more More Fewer

Professional Construction Dehumidifier 50 Liters/Day with integrated condensate pump High-performance industrial dehumidifier with automatic condensate pump, digital humidity control, and environmentally friendly R290 refrigerant – ideal for water damage, new buildings, renovations, and professional continuous operation. The professional construction dehumidifier with a dehumidification capacity of up to 50 liters per day has been specially developed for demanding use on construction sites, in cases of water damage, and for professional building drying. Thanks to its robust design, high-performance dehumidification, and integrated condensate pump, the unit is ideal for daily use by tradespeople, restoration companies, property management firms, and construction companies. With its high air output, the construction dehumidifier reliably removes excess moisture from the ambient air, significantly accelerating the drying process of walls, floors, ceilings, and building materials. At the same time, it protects buildings from consequential damage such as mold growth, corrosion, or material damage. The integrated condensate water pump offers particularly convenient operation. The resulting water is automatically drained via the included 7.5-meter hose. Manual emptying of a water tank is completely eliminated, allowing for uninterrupted 24-hour operation. Equipped with a modern LED display, digital humidity control, temperature display, operating hours counter, and an automatic defrost function, this professional dehumidifier meets all requirements for professional continuous use. Additionally, the unit uses the environmentally friendly refrigerant R290. This has an extremely low global warming potential (GWP 3) and reduces the environmental impact by around 99% compared to older refrigerants. As a result, the construction dehumidifier combines high performance with modern environmental technology. Features: Dehumidification capacity up to 50 liters/day Integrated condensate pump 7.5 m condensate hose included Pump lift up to 3 m Digital LED control panel Humidity control 10–90% Operating hours counter Temperature and humidity display Automatic defrost function Timer function Memory function after power failure Rotary compressor Environmentally friendly R290 Stackable Robust transport wheels Ideal for water damage and new construction Ideal for water damage, new construction, and professional building drying This construction dehumidifier is suitable for use wherever large amounts of moisture need to be reliably removed. Typical areas of application include water damage restoration, building shells, new construction projects, basements, warehouses, production areas, garages, archives, as well as commercial and industrial buildings. Even after painting, plastering, or screed work, the unit significantly accelerates the building drying process and shortens construction times. Thanks to the automatic humidity control, a constant room climate is maintained at all times. Convenient digital operation The clearly arranged control panel is located on the front of the unit, allowing for simple control of all functions. The target humidity, timer, and other operating parameters can be conveniently set via the easy-to-read LED display. At the same time, the current room humidity and temperature are clearly displayed at all times. Precise humidity control The desired target humidity can be set in 5% increments between 10% and 90% relative humidity. As soon as the set humidity level is reached, the unit automatically switches off the compressor and the fan. If the humidity rises again, the construction dehumidifier restarts automatically. For the long-term protection of buildings against mold and moisture, values between 50% and 55% relative humidity are recommended. For rapid drying after water damage, the unit can also be operated in continuous mode. Flexible timer function The integrated timer allows operation to be limited to between one and 24 hours or programmed with a start delay. This makes the construction dehumidifier excellent for automatic operating times or utilizing off-peak electricity tariffs. Memory function for automatic restart Thanks to the integrated memory function, the construction dehumidifier saves all the most recently selected settings. After a power failure or an interruption in the power supply, the unit automatically restarts with the same parameters. This is particularly advantageous for long-term drying projects or when used with an external timer. Especially on construction sites or in unattended buildings, this function ensures reliable and uninterrupted operation without the need for re-configuration. Integrated condensate pump for continuous operation A major advantage of this professional construction dehumidifier is the integrated condensate water pump. The extracted water is automatically drained via the included 7.5-meter long condensate hose. This eliminates the need to regularly empty a water tank and allows for unsupervised continuous operation without any issues. The pump achieves a delivery height of up to 3 meters. If the hose is laid horizontally, much longer distances can be covered. This allows the condensate to be flexibly directed into floor drains, sinks, or other suitable drains. An integrated check valve reliably prevents already pumped-out water from flowing back into the device. Additionally, the construction dehumidifier has a small internal collection container that can be completely pumped dry at the touch of a button before transport. Energy-efficient and environmentally friendly with R290 The powerful rotary compressor ensures high dehumidification performance with low energy consumption. This makes the construction dehumidifier particularly economical and ideal for daily continuous use. Modern R290 (propane) is used as the refrigerant. This natural refrigerant has a Global Warming Potential (GWP) of only 3, making it one of the most environmentally friendly solutions in the field of professional dehumidifiers. Compared to older refrigerants, the climate impact is reduced by around 99%. As a result, the unit meets current environmental standards and combines high efficiency with sustainable technology. High dehumidification performance under diverse conditions The construction dehumidifier works reliably at ambient temperatures between +5 °C and +35 °C. As with all condensation dryers, the dehumidification performance increases with higher temperatures and air humidity. This makes the unit suitable for both heated interiors and typical construction site conditions. The maximum dehumidification capacity is 50 liters per day, allowing for the rapid drying of larger buildings or heavily saturated rooms. Ambient conditions Dehumidification capacity 30 °C / 80% RH 50 liters / 24 hrs. 20 °C / 80% RH 32 liters / 24 hrs. 20 °C / 60% RH 24 liters / 24 hrs. 15 °C / 80% RH 23 liters / 24 hrs. 15 °C / 60% RH 17 liters / 24 hrs. 10 °C / 80% RH 13 liters / 24 hrs. 10 °C / 60% RH 12 liters / 24 hrs. Overview of advantages • Dehumidification capacity up to 50 liters per day• Professional construction dehumidifier for water damage and new construction• Integrated condensate pump with up to 3 m delivery height• 7.5 m condensate hose including check valve• Digital LED display with temperature and humidity display• Adjustable target humidity from 10–90%• Automatic restart after power failure (memory function)• Automatic defrost function to prevent icing• Timer function from 1 to 24 hours• Powerful rotary compressor• Environmentally friendly refrigerant R290 with GWP 3• Stackable design for space-saving transport• Large semi-pneumatic transport wheels• Suitable for continuous operation on construction sites• Ideal for water damage restoration, new buildings, basements, and industry Scope of delivery • Professional construction dehumidifier• Power cable• 7.5 m condensate hose• Check valve• User manual Technical data Dehumidification capacity Max. 50 liters / 24 hours (30 °C / 80% RH) Recommended application area Up to approx. 150 m² Air output 350 m³/h Fan stages 1 Power supply 220–240 V / 50 Hz Power consumption Max. 850 W (3.7 A)710 W at 20 °C / 60% RH Compressor High-efficiency rotary compressor Refrigerant R290 (250 g) Global Warming Potential (GWP) 3 Noise level 55 dB(A) Operating temperature +5 °C to +35 °C Humidity setting 10% to 90% RH in 5% increments Operation Digital LED control panel Display Room humidity, temperature, and operating hours Timer 1–24 hours Automatic restart Yes (memory function) Defrost system Automatic professional defrost function Condensate drainage Integrated condensate pump Pump lift Up to 3 m Condensate hose 7.5 m including check valve Condensate tank No tank required Transport Two semi-pneumatic wheels and robust handle Design Stackable Dimensions (H × W × D) 470 × 325 × 600 mm Weight 39 kg Power plug EU plug including fix-adapter for Switzerland Warranty 2 years Professional construction dehumidifier for the highest demands With its high dehumidification capacity of up to 50 liters per day, integrated condensate pump, and convenient digital control, this construction dehumidifier is perfectly suited for professional drying tasks. Whether after water damage, in new construction, or during extensive renovation work – the unit reliably ensures a rapid reduction in air humidity and significantly shortens drying times. The combination of a powerful rotary compressor, automatic humidity control, intelligent defrost function, and the environmentally friendly R290 refrigerant makes this professional dehumidifier an economical and sustainable solution for daily use. Thanks to its robust construction, large transport wheels, and stackable housing, the construction dehumidifier is optimally designed for the rigors of everyday life on construction sites.

Learn more More Fewer