A good, affordable racing horse for builders and water damage restorers. This dehumidifier has consistently omitted everything that is unnecessary for continuous operation. It has neither a display nor a hygrostat (a plug-in hygrostat can be optionally ordered if needed). This makes it very easy to operate, safe from tampering, and exceptionally low in price. On the other hand, it has everything needed for effective and quick drying: powerful dehumidification performance, hot gas defrosting, hour counter, as well as large wheels and a handle for easy mobility on construction and damage sites.     Easy handling   "The commissioning is child's play. Plug in - flip the main switch - done!"   The operation continues until either the bucket is full or the dryer is uninstalled again. As long as the device is connected to the power supply, it runs reliably and there are no settings that can be accidentally changed or manipulated. This also applies in the event of a power outage: when the power returns, the dehumidifier resumes its task with unchanged settings.   Thanks to the professional hot gas automatic control, operation in cooler environments is also possible without any issues, although the dehumidifying power, as with all condensation dryers, decreases at low temperatures. The installed finned evaporator (cooling element) has an exceptionally high efficiency in tempered environments and can dry the air to just below 40% relative humidity. Furthermore, the dryer is equipped with a rolling piston compressor. This means that it can be transported and stored in any position.     Optional Hygrostat   "Should a hygrometer for regulating the target humidity be required at any point, the dryer is prepared so that the Trotec Hygrostat HG110 can be connected directly via a jack plug. Please note the accessories."     Bucket and direct hose connection   The water extracted from the air is collected in a bucket with a capacity of 5 liters. A magnetic float automatically interrupts operation when full, and a warning light visually indicates that the bucket should be emptied. A hose can be connected to the bucket if needed, in case the water can be drained directly. The hose must be laid downwards, as no pump is integrated in the dryer.     Suitable for unattended continuous operation   This "TTK" is suitable for longer, unattended drying operations. The exact operating time can be precisely determined with the standard integrated hour meter. This is particularly useful for commercial applications. Thanks to the meter, it can also be tracked whether the device was always in operation or if it was accidentally or intentionally turned off.     Propane (R290) as an environmentally friendly refrigerant in dehumidifiers   "Every year, several million tons of environmentally harmful CO2 emissions (greenhouse gases) are released into the air due to synthetic refrigerants. Therefore, the use of alternative refrigerants is one of our most important goals. By using propane (R290) as a refrigerant, this dehumidifier makes a valuable contribution to climate protection."   The natural refrigerant propane (R290) is an organic compound and belongs to the hydrocarbons. Unlike synthetic refrigerants, environmentally friendly propane (R290) has neither ozone depletion potential (ODP=0) nor a significant greenhouse effect (GWP=3).   Supplement plus for the environment: Due to its excellent thermodynamic properties, propane (R290) is a particularly energy-efficient refrigerant, thereby additionally reducing your energy costs.     Advantages at a Glance   • Affordable price with strong performance in the commercial sector• Thanks to hot gas defrosting, it can also be used in cooler environments.• Robust steel construction with large wheels and guide bracket• Suitable for continuous operation• Thanks to the roll piston compressor, it is transportable and storable in any position.• External hygrometer connection     Technical data  dehumidification performance at 30 °C / 80 % r.H. 50 liters / day air volume 350 m³/ h Maximum room size 125 m² (310 m³) Minimum room size 8 m² (30 m³) temperature range 5 - 32°C Moisture range technical Moisture Range Practice 35 - 90 % r.F. 40 - 90 % r.H. (lamella evaporator) Voltage 220 - 240 V/50 Hz rated current consumption max. 3.7 A Power consumption max. 820W Recommended Coverage 10 A Cable length approx. 2 m Plug EU plug with Swiss adapter refrigerant R290 (230g) GWP3 water bucket 5 Liter operating noise 56 dB(A) at 1 m distance 53 dB(A) at a distance of 2.5 m Dimensions L x W x H 495 x 455 x 900 mm Weight 31 kg defrosting automatic Heissgas dehumidification automation Continuous operation, an insertable mechanical hygrometer is optionally available. Ventilator axial, single-stage blower automatic shut-off when bucket is full and prefilter and operating hour meter and Continuous operation possible and Display no memory function yes (automatically saves set values) hose connection yes, not included in the delivery (suitable inner diameter: 12 mm) guarantee 2 years Documents / Downloads   User Manual German   User manual French   User manual Italian   User manual English

Learn more More Fewer

Perfect all-rounder for construction, trade, and water damage restoration   This Trotec dehumidifier impresses with powerful dehumidification performance combined with a strong fan that blows the dried air back into the room at high speed. This means that the room air is optimally circulated, and the drying process, especially in large, highly humid, or shelf-adjusted archive and storage rooms, is significantly faster.   The vehicle construction with guiding bow, carrying troughs, and large wheels facilitates transport even in difficult terrain sections or on stair steps.   For quick commissioning, the dryer features an easy-to-use control panel with a digital display of all functions. For hygrostat-controlled automatic operation, the target value can be pre-selected in percentage steps, which is then displayed together with the current actual value. The selectable target humidity range is from 20 - 90 %, although in practice, values below 35 % are difficult to achieve. This device operates at its full capacity in at least slightly heated rooms, with an ideal temperature of 12 °C or higher.   "With the timer, you can configure the on or off times, and thanks to the integrated memory function, the settings are retained even after a power interruption. This means that operation with a timer is also possible."     Bucket and direct hose connection The water extracted from the air is collected in a bucket with a capacity of 5.5 liters. A magnetic float automatically interrupts operation when full, and a warning light visually indicates that the bucket should be emptied. A hose can be connected to the bucket if needed, in case the water can be drained directly. The hose must be laid with a downward slope, as there is no pump integrated in the dryer (optionally, a standalone condensate pump is available from us if the water can or should be transported upwards or over a distance).     With optional air hose connection for cavity drying   "Whether in suspended ceilings, in bathtub cavities, in cassette walls, or cable ducts – when moisture has penetrated poorly accessible cavities, quick action should be taken to prevent mold formation. This dehumidifier is also suitable for this purpose, as it is equipped with a specially powerful fan with 3.2 MPa air pressure. An air hose with a suitable adapter can be optionally attached to it, allowing the dry air to be directed precisely to the damp areas."   Note: If there is heavy dirt, dust, or already mold in the cavity, the room should ideally not be occupied or used during this drying process, as otherwise, dust particles and mold spores can spread everywhere. In this case, the additional use of an air purifier is recommended.      Propane (R290) as an environmentally friendly refrigerant in dehumidifiers   "Every year, several million tons of environmentally harmful CO2 emissions (greenhouse gases) are released into the air due to synthetic refrigerants. Therefore, the use of alternative refrigerants is one of our most important goals. By using propane (R290) as a refrigerant, this dehumidifier makes a valuable contribution to climate protection."   The natural refrigerant propane (R290) is an organic compound and belongs to the hydrocarbons. Unlike synthetic refrigerants, environmentally friendly propane (R290) has neither ozone depletion potential (ODP=0) nor a significant greenhouse effect (GWP=3).   Supplement plus for the environment: Due to its excellent thermodynamic properties, propane (R290) is a particularly energy-efficient refrigerant, thereby additionally reducing your energy costs.     Advantages at a Glance   • Particularly economical solution for typical dehumidification applications in the commercial sector• High dehumidification performance even at low temperatures• Air hose connection for localized dry air application or cavity drying• Robust steel construction in vehicle design• Thanks to the roll piston compressor, it is transportable and storable in any position.• Timer Function• Memory function (auto-restart function)• Permanent mode for continuous operation• Maintenance-friendly magnetic closure door   Technical data   dehumidification performance at 30 °C / 80 % r.H. 51 liters / day air volume 450 m³/ h Maximum room size 130 m² (330 m³) Minimum room size 12 m² (30 m³) temperature range 5 - 30°C Moisture range technical Moisture Range Practice 20 - 90 % r.F. 35 - 90 % r.H. (lamella evaporator) Voltage 220 - 240 V/50 Hz rated current consumption max. 2.7 A Power consumption max. 650W Recommended Coverage 10 A Cable length approx. 2 m Plug EU plug with Swiss adapter refrigerant R290 (230g) GWP3 water bucket 5.5 Liter operating noise 52 dB(A) at 1 m distance 49 dB(A) at a distance of 2.5 m Dimensions L x W x H 525 x 490 x 900 mm Weight 40 kg defrosting automatic Recirculation, electronic dehumidification automation Hygrostatgesteuert Ventilator radial, single-stage blower automatic shut-off when bucket is full and prefilter and Timer and Continuous operation possible and Display shows current room humidity, set air humidity memory function yes (automatically saves set values) hose connection yes, no hose included in the delivery guarantee 2 years

Learn more More Fewer

Powerful air dehumidifier / construction dryer 50B-WDH with calibrated consumption meter.The "50B" has been specifically designed to quickly dry water damage, e.g. after flooding or inundations. It features a very strong dehumidification performance and only has a power switch for optimal operation on construction sites and during water damage drying. A hygrometer for regulating the target humidity has been deliberately omitted in this version. Recommended room size up to 120m², from 8°C. The performance and drying speed can be additionally accelerated with free-standing fans if needed (e.g. FN45 from our range).Characteristics • Dehumidification capacity of up to 42 liters / day (at 30°C/80% r.H.)• Function for continuous operation/continuous dehumidification• calibrated consumption meter (kWh)• On/Off toggle switch• Equipped with a highly efficient rotary compressor. This compressor is one of the most powerful compressors on the market.• Automatic professional defrost function• Removable condensate tank• Connection possibility of a hose for continuous drainage of the condensate• Powder-coated metal housing/metal frame• Very easy mobility due to transport handles and large running wheels for safe travel over steps and uneven ground.• Operating warning light / Defrost light• No separate or additional coolant is required (closed circuit)• Washable air filter grid• Environmentally friendly refrigerant R290• CFC free and compliance with WEEE standards ImportantThe construction dryer "50B" is not suitable for use in very cold rooms, as it can freeze during continuous operation below 8°C due to the powerful dehumidification unit.   dehumidification performanceThe dryer is via a Temperature range from +8°C to +32°C is applicable, whereby, as with all condensation dryers, the dehumidifying power decreases in cooler environments. Examples of dehumidification performance and consumption under various (constant) ambient conditions:30°C/80% r.H.: approx. 42 liters (at 60% r.H.: approx. 21 liters)20°C/80% r.H.: approx. 21 liters (at 60% r.H.: approx. 12 liters)15°C/80% r.H.: approx. 15 liters (at 60% r.H.: approx. 8 liters)10°C/80% r.H.: approx. 8 liters (at 60% r.H.: approx. 6 liters)(r.H.=relative humidity)Technical data  Tension 220-240V / 50Hz Power consumption: max. 820 (3.7 A) or 620W (at 20°C/60% r.H.) Sound pressure level: 57 dB(A) (Manufacturer's specification) dehumidification performance 42 liters/day (30°C / 80% r.H.)  amount of recirculated air 400 m³/h (installed) condensate tank approx. 5 liters (direct hose connection possible) Compressor Rotary compressor  refrigerant R290 (230gr.) Dimensions (H x W x D)  890 x 450 x 740 mm Weight 32 Kg cessation of operations ON/OFF toggle switch Ambient temperature 8°C ~ 32°C Area of application Rooms from min. 10m² to max. 120m² Swiss plug: EU plug with fixed adapter for Switzerland  hose connection Yes guarantee 2 years

Learn more More Fewer

The Oasis dehumidifiers are among the widely used drying devices that have been successfully employed on construction sites and by private users for many years. The devices have now been revised and adapted to the latest state of technology with the newest environmentally friendly refrigerant R290 and improved efficiency. The Oasis D165 is suitable for basements and rooms up to 90m² and comes standard with a large bucket as well as a direct hose connection.Although visually very similar, the D165 dehumidifier has been completely revised in various respects compared to its predecessor:• improved efficiency• higher dehumidification performance• environmentally friendly refrigerant R290• improved automatic self-defrosting, thus usable down to 5°C (previously: 8°C)• reinforced front cover with spark guard bowl• reinforced, load-bearing wheelsThe dryer stands on 4 wheels but can also be mounted on a suitable wall bracket available from us if desired. The air intake area is at the back, where a filter cleans the moist air. The filter itself is easy to remove and clean. The dry air is blown out towards the front into the room. The Oasis is therefore ideal for general moisture control in a classic basement environment, for example in new buildings, but also for unattended continuous operation in temperature-controlled archives and on construction sites. For active laundry drying, the blower is rather too weak.The target humidity is regulated via a stepless hygrostat on the front. Once the set value is reached, the dehumidification operation pauses (the ventilation also stops) until the humidity rises again. The operation continues with the unchanged setting even after a power interruption. The D165 is therefore also suitable for operation with a timer, if you want to run the dryer, for example, only during off-peak hours. Thanks to the pipe evaporators, the D165 extracts water from the air even in low humidity ranges.The water is collected in the tank pushed in at the back, a float mechanically interrupts operation when full. Alternatively, a hose can be screwed onto the condensate collection tray (with a coupling / 3/4-inch thread), with the hose needing to have a slope towards the drain (no pump integrated in the device).usage examplesCellar Moisture: Ideal for damp cellars, old walls, and laundry rooms. Eliminates musty odors, stops mold growth, decomposition of masonry, and much more.Construction and Industrial Dryers: thanks to their handy, robust design, they are ideally suited for drying on construction sites and in the industry.Drying of Water Damage: The Oasis removes water from the air even in deep moisture areas through the pipe evaporators. This significantly accelerates the drying of water damage.dehumidification performanceThe dryer can be used thanks to hot gas defrosting over a wide temperature range from +5°C to +32°C, although, as with all condensation dryers, the dehumidifying power decreases in cooler environments. Examples of dehumidification performance and consumption under various (constant) environmental conditions:  30°C/80% r.H.: 28 liters / 24 h27°C/60% r.H.: 16.8 Liters / 24 h20°C/60% r.H.: 10.8 Liters / 24 h10°C/70% r.H.: 5.3 Liters / 24 h(r.H.=relative humidity)    Massive improvement regarding environmental compatibilityThe GWP (Global Warming Potential - impact on global warming) could be reduced by a factor of 800 (!) from 1430 (R134a) to less than 2 (R290). Furthermore, the D165 requires 10% less electricity while simultaneously increasing dehumidification performance by 14% (at room temperature 20°C, 60% r.H.). Technical data  Tension 230V / 50Hz Power consumption max. 360W Sound pressure level 1 m distance 54 dB(A) (our measurement) 2.5 m distance 51 dB(A) (our measurement) dehumidification performance max. 28 liters/day (30°C / 80% r.H.)  Bucket Capacity 9 liters, approx. 8 liters until operation interruption by float Compressor Rotary compressor  refrigerant R290 (150gr.) Dimensions (H x W x D)   60 x 38 x 36 cm (incl. wheels) Weight 23.5 Kg cessation of operations Hygrostatrad   Ambient temperature 5°C ~ 40°C  Area of application about 90m² Swiss plug Yes   hose connection Yes operating hour meter Yes guarantee 2 years    

Learn more More Fewer

Mit seiner kräftigen Entfeuchtungsleistung meistert dieser Profi-Bautrockner auch anspruchsvolle Aufgaben. Die integrierte Kondensatwasserpumpe sorgt für einen komfortablen Betrieb, da das anfallende Wasser automatisch abgeleitet wird. Zusätzlich erhalten Sie weitere Profi-Funktionen wie ein Betriebsstundenzähler, eine Temperaturanzeige, eine Feuchtigkeitsanzeige sowie eine automatische Abtau-Funktion. Gemessen an seiner Entfeuchtungskraft ist er sparsam im Verbrauch und verfügt über das neue Kältemittel "R290", welches die Umwelt kaum noch belastet. So liegt das "Global Warming Potential (GWP)" bei einem Wert von 3, was gegenüber vergleichbaren Modellen früherer Generationen einer Reduktion von 99.85% entspricht. Bedienung Das Bedienerfeld liegt vorne am Gehäuses und bietet verschiedene Möglichkeiten: Einstellung Zielfeuchte per Tastendruck wird die gewünschte Zielfeuchte eingestellt, also der Wert, auf den das Gerät den Raum stabil halten soll. Ist die gemessene Feuchtigkeit im Raum höher, läuft der Betrieb. Stimmt die Feuchte, pausiert das Gerät, wobei nicht nur der Kompressor, sondern auch der Lüfter stoppt. Die gewünschte Zielfeuchte kann in 5 %-Schritten zwischen 10 - 90 % gewählt werden, wobei die Einstellung auf 10 % Dauerbetrieb entspricht. Um einen Raum vor Schimmel und Gerüchen zu schützen, reicht ein Wert von ca. 60%, ideale Einstellung ist also 50 oder 55%. Tiefere Werte bringen keinen zusätzlichen Vorteil, es sei denn, man trocknet Wasserschaden. Timer Mit dem Timer kann der Betrieb entweder "ab jetzt" zeitlich limitiert werden (1-24 Stunden) oder auf einen Zeitpunkt 1-24 Stunden in die Zukunft gestartet werden, zum Beispiel dann wenn man den Betrieb auf den Niedertarif starten möchte. Memory-Funktion Wenn man das Gerät jeden Tag zu gleichen Uhrzeiten laufen lassen möchte (zum Beispiel im Niedertarif), dann kann man das mit einer handelsüblichen Zeitschaltuhr/Timer machen. Der Trockner merkt sich die letzte Einstellung und kommt nach Stromunterbruch mit unveränderten Einstellungen zurück. Pumpe Anstelle eines Eimers ist bei diesem Modell eine Wasserpumpe integriert, welche das entzogene Kondensat wegpumpt. Der im Lieferumfang enthaltene Schlauch ist 7.5m, kann aber auch verlängert werden. Wenn der Schlauch flach verlegt wird, kann das Wasser problemlos Distanzen bis 20 m bewältigen. Bei Abpumpen in die Höhe verringert sich die mögliche Distanz je nach Höhendifferenz. Ein Rückschlagventil verhindert dabei, dass im Schlauch stehendes Wasser ins Gerät zurückfliesst. Im Gerät selbst befindet sich ein kleiner Tank, welcher vor dem Transport per Tastendruck vollständig ausgepumpt werden kann. Vorteile im Überblick Entfeuchtungsleistung von bis zu 65 Ltr./Tag Professioneller Betriebsstundenzähler für die Kontrolle der Einsatzdauer Im Lieferumfang sind 7.5 Meter Kondensschlauch inkl. einem Rückschlagventils enthalten Temperaturanzeige (Eingang / Ausgang) zur Überwachung der Umgebungsbedingungen Integrierte Pumpfunktion, mit der Sie das Kondensat bis zu 3 Meter Förderhöhe abpumpen können Automatischer Betriebsfortlauf nach einem Stromausfall Ausgestattet mit einem hocheffizienten Rotationskompressor für maximale Leistung und Energieeffizienz Übersichtliches LED-Display inkl. Feuchtigkeitsanzeige für einfache Bedienung und Kontrolle Feuchtigkeitsregelung in 5% Schritten zwischen 10% bis 90% für präzise Trocknungsergebnisse Automatische Profi Defrost Funktion zur Vermeidung von Eisbildung im Kühlsystem Timer Funktion pro Stunde für flexible Trocknungsdauer Stapelbar zum Platzsparen für einfachen Transport und Lagerung Zwei semi-pneumatisch Reifen, für einfachen Transport CE (EMC + LVD) Konformität sowie "GS" geprüft. Lieferumfang Bautrockner Netzkabel Kondensatschlauch mit Rückschlagventil Bedienungsanleitung Entfeuchtungsleistung Der Trockner ist über ein breites Temperaturspektrum zwischen +5°C bis +35°C einsetzbar, wobei wie bei allen Kondensationstrocknern die Entfeuchtungskraft in kühlerer Umgebung abnimmt. Beispiele der ungefähren Entfeuchtungsleistung bei verschiedenen (konstanten) Umgebungsbedingungen: 30 °C: 80 % feucht: 65 Liter / 24 Std. - 60 % feucht: 42 Liter / 24 Std. 20 °C: 80 % feucht: 32 Liter / 24 Std. - 60 % feucht: 24 Liter / 24 Std. 15 °C: 80 % feucht: 23 Liter / 24 Std. - 60 % feucht: 17 Liter / 24 Std. 10 °C: 80 % feucht: 13 Liter / 24 Std. - 60 % feucht: 12 Liter / 24 Std. Technische Daten Spannung 220-240V / 50Hz Leistungsaufnahme max. 850 (3.7 A) resp. 710W (3.1 A) bei 20°C/60% r.F. Schalldruckpegel 55 dB(A) (Angabe Hersteller) Entfeuchtungsleistung max. 65 Liter/Tag (30°C / 80% r.F.) Umluftmenge 350 m³/h, 1 Ventilationsstufe Kondenstank Kein Tank, integrierte Pumpe mit 7.5 m Schlauch Kompressor Rotationskompressor Kältemittel R290C (250gr.) Abmessung (H x B x L) 470 x 325 x 600 mm Gewicht: 39 Kg Betriebseinstellung: Digitales Bedienerfeld Umgebungstemperatur: 5°C ~ 35°C Einsatzbereich: bis 150 m² Schweizerstecker: EU-Stecker mit Fix-Adapter für die Schweiz Schlauchanschluss: Ja Garantie: 2 Jahre

Learn more More Fewer

The universal all-rounder   "Whether for drying out after water damage, new building drying, or maintaining dry conditions in heated and unheated storage rooms - the 170S is a universally applicable dehumidifier with high-quality workmanship and reliable operation. It is manufactured in a specialized plant in Europe. It is built to last, easy to maintain, rarely needs servicing, and is very affordable considering its power and quality.".     Easy handling   "Using a mechanical hygrometer, the desired target humidity can be continuously adjusted between 32 - 100%, and continuous operation is also possible. Particularly useful in larger areas is the high air circulation volume of a substantial 580 cubic meters per hour. With its stable cart construction and large wheels, frequent relocation to different usage sites can be easily carried out."     Bucket, direct hose connection and optional pump kit   The water, which is extracted from the air, flows into the 6-liter bucket. This is placed on a scale that automatically interrupts operation when full. A control light indicates the full status in this case. Furthermore, there is the possibility to connect a hose if the water can be drained directly. The hose must have a slope towards the drain in this case. If this is not possible, a suitable pump kit is optionally available, with which the water can be pumped upwards and also outwards.   "The operating switch and level warning light are protected against dust and splashing water by a protective cover, and a slotted hygrostat rotary switch prevents unwanted adjustment of the switch position."     Professional Hot Gas Defrosting   Inside, a professional hot gas defrosting automatic system ensures effective dehumidification results. The fin evaporators unleash their power particularly in temperature ranges above 10°C and in areas above 40% humidity. Technically, the dryer can also be used in lower ranges down to about 5°C, even in unattended continuous operation.     Optional counters   The delivery includes no "Hour or consumption meters are included. You can order them from us upon request (the housing is standardly prepared for retrofitting). You have the choice between a pure hour meter or the combined dual meter, which measures hours and electricity consumption. The meters are MID compliant. Outside of Switzerland, dryers in professional use must already be MID compliant."     Propane (R290) as an environmentally friendly refrigerant in dehumidifiers   Annually, several million tons of environmentally harmful CO2 emissions (greenhouse gases) are released into the air due to synthetic refrigerants. Therefore, the use of alternative refrigerants is one of our most important goals. By using propane (R290) as a refrigerant, this dehumidifier makes a valuable contribution to climate protection. The natural refrigerant propane (R290) is an organic compound and belongs to the hydrocarbons. Unlike synthetic refrigerants, environmentally friendly propane (R290) has neither ozone depletion potential (ODP=0) nor a significant greenhouse effect (GWP=3).   Supplement Plus for the Environment: Due to its excellent thermodynamic properties, propane (R290) is a particularly energy-efficient refrigerant, thereby additionally reducing your energy costs.     Advantages at a Glance   • High dehumidification performance even at low temperatures• Robust plastic-coated metal housing• Thanks to the roll piston compressor, it is transportable and storable in any position.• Stable carriage construction• Automatic hygrostat-controlled dehumidification operation• Quality hot gas defrost automatic system• Option to retrofit MID-compliant dual meter for operating and kilowatt hours (optional) • Option to add a suitable pump kit that can be connected directly to the device (optional)   Technical data  dehumidification performance at 30 °C / 80 % r.H. 40 liters / day air volume 580 m³/ h Maximum room size 100 m² (250 m³) Minimum room size 8 m² (20 m³) temperature range 5 - 32°C Moisture range technical Moisture Range Practice 32 - 90 % r.F. 40 - 90 % r.F. Voltage 220 - 240 V/50 Hz rated current consumption max. 2.8 A Power consumption max. 600W Recommended Coverage 10 A Cable length approx. 3 m Plug EU plug with Swiss adapter refrigerant R290 (150g) GWP3 water bucket 6 Liter operating noise 52 dB(A) at 1 m distance 49 dB(A) at a distance of 2.5 m Dimensions L x W x H 540 x 490 x 963 mm (incl. guide bracket) Weight 32 kg defrosting automatic Heissgas dehumidification automation Hygrostatgesteuert Ventilator axial, single-stage blower automatic shut-off when bucket is full and prefilter and Timer no (operation on timer possible) Continuous operation possible and memory function yes (mechanically stores set values) hose connection yes (no hose included in the delivery) - 12 mm Pump optional available (not included in the scope of delivery) guarantee 2 years

Learn more More Fewer

Professional construction dehumidifier with large bucket A high-quality dehumidifier for commercial use and water damage drying, manufactured in Europe. Its impressive exterior appearance is matched by its internal values: all electrical components are specially encapsulated, protecting the electronics from harmful deposits that could impair their function and longevity. Therefore, this dryer is also ideally suited for use under demanding conditions. Thanks to its maintenance-friendly design, it is easy to care for. "Compared to more affordable piston compressors, the high-quality 0.58 kW rotary compressor installed here offers the advantage of higher performance with comparatively lower power consumption – and additionally provides reserves for high dehumidification performance even in unheated rooms."In addition, the high-quality hot gas defrosting automatic system ensures a much more efficient dehumidification performance compared to other defrosting devices, without time interval-related defrosting pauses during which no dehumidification takes place.  Propane (R290) as an environmentally friendly refrigerant in dehumidifiers Annually, several million tons of environmentally harmful CO2 emissions (greenhouse gases) are released into the air due to synthetic refrigerants. Therefore, the use of alternative refrigerants is one of our most important goals. By using propane (R290) as a refrigerant, this air dehumidifier makes a valuable contribution to climate protection. The natural refrigerant propane (R290) is an organic compound and belongs to the hydrocarbons. Unlike synthetic refrigerants, environmentally friendly propane (R290) has neither ozone depletion potential (ODP=0) nor a significant greenhouse effect (GWP=3).  Supplement plus for the environment: Due to its excellent thermodynamic properties, propane (R290) is a particularly energy-efficient refrigerant, thereby additionally reducing your energy costs.  User-friendly Thanks to its durable housing, ergonomic grip recesses with an internal grip clip, and four sturdy wheels with a roll stop, the device is ideally suited for use on construction sites and for drying water damage. However, these advantages are also appreciated in commercial spaces or in private basement environments. The storage is also well thought out: two practical stacking grooves on the top of the device allow for a stable and space-saving stacking during transport and in storage.   An integrated operating hour meter reliably documents the exact duration of use even during longer drying operations.   Integrated compressor thermal protection with automatic shut-off   In drying operations with extremely high humidity and simultaneously high temperatures – for example, during water damage restoration – refrigerant dryers quickly enter their red performance zone. Here, the catchy "35 rule" applies: water damage above 35 degrees reduces the dryer’s lifespan to below 35%. However, this is not a question of component quality, but pure physics, which applies independently of the manufacturer to all refrigerant dryers on the market.  While most professional condensate dryers can still operate without issues at moderate humidity around 70% r.F. up to 35 °C, very high humidity combined with high room temperature results in significantly more energy being supplied to the humid air, which must be additionally "processed" through the refrigerant. Consequently, the pressure of the refrigerant in the system increases immensely, leading to a destructive load on the compressor. Although the dehumidifiers will initially continue to operate, they will do so well beyond their limit "deep in the dark red zone," resulting in an extremely shortened remaining lifespan.  "Therefore, the commercial dehumidifiers of the TTK-S series are equipped with an integrated compressor thermal protection for the active preservation of your devices:"Sensors continuously monitor the thermal load of the compressor. If the temperature is within the defined operating range, the integrated heat protection indicator pulses in a long sequence, indicating optimal operation of the dehumidifier. As soon as the temperature exceeds the critical threshold of 35 °C, the automatic system switches off the compressor to protect it, while the fan continues to operate, and automatically reactivates the compressor as soon as the 35° threshold is fallen below again. This protection not only significantly extends the lifespan of the dehumidifiers, but also prevents thermal damage to materials in the room and the building structure during their use.   Options • Dual meter available for additional recording of electricity consumption.• high-performance condensate pump for permanent drying with a pumping capacity of up to 50 m distance and a maximum delivery height of 4 m  Advantages at a Glance • High dehumidification performance even at low temperatures • Maximum dust and moisture protection for all electrical components• Extremely maintenance-friendly design • Optimal handling characteristics • Thanks to the roll piston compressor, it is transportable and storable in any position. • Practical stacking groove for stable, space-saving storage and transport • Multistage capability with identical models• Practice-oriented industrial design• Made in Europe  Technical data  dehumidification performance at 30 °C / 80 % r.H. 28 liters / day air volume 250 m³/ h Maximum room size 70 m² (175 m³) Minimum room size 8 m² (30 m³) temperature range 5 - 32°C moisture range 35 - 90 % r.F. Voltage 220 - 240 V/50 Hz rated current consumption max. 2.3 A Power consumption max. 500W Recommended Coverage 10 A Cable length approx. 3 m Plug EU plug with Swiss adapter refrigerant R290 (150g) GWP3 water bucket 6 Liter operating noise 52 dB(A) at 1 m distance 49 dB(A) at a distance of 2.5 m Dimensions L x W x H 375 x 345 x 603 mm Weight 26 kg defrosting automatic Heissgas dehumidification automation Hygrostatgesteuert Ventilator axial, single-stage blower automatic shut-off when bucket is full and prefilter and Timer no Continuous operation possible and memory function yes (mechanically stores set values) hose connection yes, short hose piece included in the delivery guarantee 2 years   

Learn more More Fewer

The robust and powerful all-rounder   "Whether for drying out after water damage, new building drying, or maintaining dry conditions in heated and unheated storage rooms - the 350S is a universally applicable dehumidifier with high-quality workmanship and reliable operation. It is manufactured in a specialized plant in Europe. It is built to last, easy to maintain, rarely requires servicing, and is very affordable considering its power and quality."  Easy handling The desired target humidity can be continuously regulated between 32 - 100% using a mechanical hygrostat, and continuous operation is also possible. With the used lamella evaporator, target humidities below 40% r.H. are difficult to achieve; however, this technology shows impressive dehumidification power in temperate and humid environments. Particularly useful in larger areas is the high air circulation volume of a substantial 1000 cubic meters per hour. With its stable trolley construction and large wheels, frequent relocation to different sites can be easily carried out.  Bucket, direct hose connection and optional pump kit The water, which is extracted from the air, flows into the 6-liter bucket. This is placed on a scale that automatically interrupts operation when full. A control light indicates the full status in this case. Furthermore, there is the possibility to connect a hose if the water can be drained directly. The hose must have a slope towards the drain in this case. If this is not possible, a suitable pump kit is optionally available, with which the water can be pumped upwards and also outwards. "The operating switch and level warning light are protected against dust and splashing water by a protective cover, and a slotted hygrostat rotary switch prevents unwanted adjustment of the switch position."     For continuous operation on construction sites   The possibility of connecting an external condensate drain – optionally with a condensate pump if needed – makes the construction dryer also ideally suited for longer unattended drying tasks, e.g. in construction drying.     Optional counters The delivery does not include an hour or consumption meter. You can order these from us if desired (the housing is standardly prepared for retrofitting). You have the choice between a pure hour meter or the combined dual meter, which measures hours and power consumption. The meters are MID compliant. Outside of Switzerland, dryers in professional use must already be MID compliant.     Hydrofluorolefin (R-454C) as an environmentally friendly refrigerant in dehumidifiers   "Every year, several million tons of environmentally harmful CO2 emissions (greenhouse gases) are released into the air due to synthetic refrigerants. Therefore, the use of alternative refrigerants is one of our most important goals. By using hydrofluoroolefin (R-454C) as a refrigerant, this dehumidifier makes a valuable contribution to climate protection."   The natural refrigerant hydrofluoroolefin (R-454C) is an organic compound and belongs to the hydrocarbons. Unlike synthetic refrigerants, the environmentally friendly hydrofluoroolefin (R-454C) has neither ozone depletion potential (ODP=0) nor a significant greenhouse effect (GWP=146).   Supplement Plus for the Environment: Due to its excellent thermodynamic properties, hydrofluoroolefin (R-454C) is a particularly energy-efficient refrigerant, thereby additionally reducing your energy costs.     Advantages at a Glance • High dehumidification performance even at low temperatures• Robust plastic-coated metal housing• Thanks to the roll piston compressor, it is transportable and storable in any position.• Stable carriage construction• Automatic hygrostat-controlled dehumidification operation• Quality hot gas defrost automatic system• Option to retrofit MID-compliant dual meter for operating and kilowatt hours (optional)• Option to add a suitable pump kit that can be connected directly to the device (optional)     Technical data   dehumidification performance at 30 °C / 80 % r.H. 55 liters / day air volume 1000 m³/ h Maximum room size 140 m² (350 m³) Minimum room size 8 m² (20 m³) temperature range 5 - 32°C Moisture range technical Moisture Range Practice 32 - 90 % r.F. 40 - 90 % r.F. Voltage 220 - 240 V/50 Hz rated current consumption max. 6.1 A Power consumption max. 1400W Recommended Coverage 10 A Cable length approx. 3 m Plug EU plug with Swiss adapter refrigerant R454C (650g) GWP146 water bucket 6 Liter operating noise 54 dB(A) at 1 m distance 51 dB(A) at a distance of 2.5 m Dimensions L x W x H 530 x 500 x 965 mm (incl. guide bracket) Weight 39 kg defrosting automatic Heissgas dehumidification automation Hygrostatgesteuert Ventilator axial, single-stage blower automatic shut-off when bucket is full and prefilter and Timer no (operation on timer possible) Continuous operation possible and memory function yes (mechanically stores set values) hose connection yes (no hose included in the delivery) Pump optional available (not included in the scope of delivery) guarantee 2 years

Learn more More Fewer

The combination of compact dimensions and high dehumidification performance makes this model ideal for construction drying and drying after water damage. In addition, the dehumidifier is excellent for keeping commercial properties, archives, and production areas dry. Thanks to its two large wheels and practical handle, it can be easily moved across various objects.   Operation 'Through the digital control panel at the front, the desired target humidity can be selected in 1% increments between 40-80%. Continuous operation is also possible. The set values can be saved at the push of a button. This way, in the event of a power interruption, operation will automatically continue with unchanged settings as soon as the power supply is restored.'  The humid room air is drawn in from the front and cleaned of dust and dirt by a pull-out, easy-to-clean filter. The dried air is then blown out at the back. The display shows the currently measured humidity.   The water extracted from the air can be collected in the inserted bucket or discharged directly through a hose (suitable inner diameter: 12 mm). A float automatically interrupts operation when the bucket is full. If the water is discharged through the hose, it first passes through the bucket to which the hose connector is attached. This system is very safe: if the hose is clogged, kinked, or not properly laid, the water backs up into the bucket. When the bucket is full, operation stops. Overflow onto the floor is therefore not possible, unlike dryers where the hose is directly attached to the drip tray.     Important functions   • Digital control and side-mounted operating hour meter• High efficiency thanks to automatic hot gas defrosting• Robust housing with two large running wheels and guide handle• Easy operation• Built-in hygrometer• Water container with automatic shut-off when full• Possibility to connect a hose for direct drainage of condensate• Air filter     Suitable for • Drying of commercial spaces and archives• Drying of water damage• Building drying• Industry and Production• Rental  Propane (R290) as an environmentally friendly refrigerant in dehumidifiers"Every year, several million tons of environmentally harmful CO2 emissions (greenhouse gases) are released into the air due to synthetic refrigerants. Therefore, the use of alternative refrigerants is one of our most important goals. By using propane (R290) as a refrigerant, this dehumidifier makes a valuable contribution to climate protection." The natural refrigerant propane (R290) is an organic compound and belongs to the hydrocarbons. Unlike synthetic refrigerants, environmentally friendly propane (R290) has neither ozone depletion potential (ODP=0) nor a significant greenhouse effect (GWP=3). "Supplement plus for the environment: Due to its excellent thermodynamic properties, propane (R290) is a particularly energy-efficient refrigerant, thereby additionally reducing your energy costs."      Technical data   dehumidification performanceat 20 °C / 60 % r.H.at 30 °C / 80 % r.H.   20.3 liters / day45.6 liters / day Air volume max. 350 m³/ h Maximum room size 115 m² (280 m³) Temperature range 5 - 35 °C Moisture range technical Moisture Range Practice 35 - 90 % r.F.40 - 90 % r.H. (lamella evaporator) voltage 220 - 240 V/50 Hz Nominal current consumption max. 4 A Power consumption max. 900 W Recommended Coverage 10 A Plug Connection cable with EU plug and Swiss fixed adapter refrigerant R290 (GWP: 3) Bucket + Hose connection 5.7 liter bucket and direct hose connection (suitable hose 12mm inner diameter) Operating noise 55 dB(A) at 1 m distance52 dB(A) at a distance of 3 m Masse (B x H x T) 422 x 820 x 580 mm Weight 30 kg Automatic defrosting Heissgas Attitude Digital Operator Panel Ventilator axial, single-stage blower Compressor Rolling piston Prefilter and operating hour meter and Continuous operation possible and Display and Memory function yes (set values saved on button press) Guarantee 2 years

Learn more More Fewer

This extremely powerful dehumidifier is specifically designed for demanding dehumidification tasks, such as the rapid drying of water damage, effective construction drying in large or heavily damp rooms, as well as the gentle drying of herbs. Due to its high performance, this dryer is available exclusively with a hose connection, making the use of a water container unnecessary and allowing for continuous operation.The dryer is to be set up freestanding in the room, with the clearly arranged control panel and the intake area for the humid room air positioned at the front of the device for easy access. The generated dry air is distributed widely in the room with high volume and strong airflow through the side outlet to ensure efficient and uniform dehumidification. A washable air filter in the intake area reliably protects the interior of the device from dust and dirt, thus contributing to the longevity and performance of the dehumidifier.SettingsThe operator panel displays the currently measured room humidity and the set target humidity. If desired, the room temperature and the remaining time of any activated timer can also be queried. Using the buttons, the desired target humidity can be set in 5% increments between 20-90%. Once the desired humidity is reached, the compressor pauses while the ventilation continues to verify the current humidity in the room. In addition to humidity-dependent operation, continuous operation is also possible.Furthermore, the device has a timer that allows the runtime to be limited to 1-24 hours once, or it can set the start time to a later point 1-24 hours in the future. If the operation is to start and end at the same time every day, this can be done with a standard timer. Thanks to the memory function, the settings are saved, so that operation can be resumed with unchanged settings after a power interruption.condensationThe condensate is drained directly through a hose into a lower-lying drain. The dryer does not have a bucket. A hose piece of about one meter is included in the delivery.Temperature protectionIf the room temperature drops too low (below +5°C) or rises too high (above +35°C), a safety mechanism will interrupt operation until the temperature in the room is back to normal. dehumidification performanceThe dryer can be used over a wide temperature range from +5°C to +35°C thanks to its advanced hot gas defrosting, although, as with all condensation dryers, the dehumidifying power decreases in cooler environments. Examples of dehumidification performance and consumption under various (constant) environmental conditions:30°C / 80% r.H. = 90.0 Liters / 24h (1080W)27°C / 60% r.H. = 50.0 Liters / 24h (920W)20°C / 80% r.H. = 45.0 liters / 24h20°C / 60% r.H. = 27.0 Liters / 24h10°C / 60% r.H. = 13.0 Liters / 24h(r.H.=relative humidity)    Characteristics• Dehumidification capacity of up to 90 liters per day • Electric hygrostat (LED) for regulating and setting the desired humidity • Function for continuous operation/continuous dehumidification • Memory function for storing data and for automatic resumption of operation after power interruption• Clear display including current humidity, target humidity, and status overview• Equipped with a high-efficiency rotary compressor (Rotary Compressor)• Automatic professional defrost function• Humidity control in 5% steps between 20% - 90% (plus continuous operation function)• Powder-coated metal housing/ metal bracket• Very easy mobility due to transport handles and 2 large and 2 smaller running wheels• Operating warning light / Defrost light• Maintenance-free / No separate or additional coolant is required (closed circuit)• Air filter grid that can be cleaned• The device is immediately ready for use (no installation or assembly required)• Swiss plug 230 V • CFC-free and compliance with WEEE standards, CE, REACH, GS, and RoHS certified.• Environmentally friendly refrigerant R290Examples of useDehumidifier: Ideal for quick drying of concrete, basements, plaster, screed, water damage, etc.Damage Removal: After flooding or damage caused by extinguishing water, these devices are ideally suited for drying (professionals as well as insurance companies use these devices.)Drying of Herbs and Wood: Significantly accelerates the drying of wood as well as herbs such as tea, CBD, etc., and prevents mold formation on the drying material.  Technical data   Tension 220-240V / 50Hz Power consumption max. 1080W (4.8A) Sound pressure level 1 m distance 62 dB(A)2.5m distance 59 dB(A)(our measurement) dehumidification performance max. 90 liters/24h (30°C / 80% r.H.)  Recirculation air volume 850 m³/h (free-blowing) Condensation tank No tank / only hose connection possible Compressor Rotary compressor  refrigerant R290 (GWP: 3) Dimensions (H x W x D)  1010 x 584 x 575 mm Weight 54 Kg Operational cessation per key press / digital display Ambient temperature 5°C ~ 35°C Area of application Rooms from min. 14m² to max. 230m² (650m³) Swiss plug Yes   hose connection Yes operating hour meter No Guarantee 2 years

Learn more More Fewer

Trotec TTK 355 S – Kraftvoller Bautrockner für härteste Einsätze Ob bei der schnellen Reduktion hoher Luftfeuchtigkeit oder zur zuverlässigen Trocknung grossvolumiger Räume – der TTK 355 S ist exakt für solche Herausforderungen konzipiert. Seine beeindruckende Leistung verdankt das Gerät der effektiven Kombination eines leistungsstarken Rollkolbenkompressors mit einem Qualitätsgebläse, das Luftmengen von bis zu 490 m³/h verarbeitet. Diese hohe Luftumwälzung erlaubt es dem optimierten Wärmetauschersystem, kontinuierlich große Mengen Feuchtigkeit aus der Raumluft zu ziehen – bis zu 70 Liter pro Tag mit nur einem Gerät. Ein besonderes Plus bietet die integrierte Heissgas-Abtauautomatik: Sie verhindert Entfeuchtungspausen durch feste Abtauintervalle, wie sie bei vielen anderen Geräten üblich sind, und sorgt so für eine gleichmässige und effiziente Leistung – selbst bei kühleren Einsatzbedingungen. Mobilität trifft auf Robustheit Auch für wechselnde Einsatzorte und raue Umgebungen ist der TTK 355 S bestens gerüstet. Das robuste Fahrgestell mit praktischer Griffbügelstange und grossen Gummirädern macht den Transport – auch über Treppen oder unebenen Boden – denkbar einfach. Die verbauten Gummiräder sind abriebfest und hinterlassen keinerlei Spuren auf empfindlichen Bodenbelägen. Dank der Rollkolbenkompressor-Technologie kann der TTK 355 S zudem in nahezu jeder Position transportiert werden. Ein spezielles Schutzsystem für die Elektronik bewahrt die sensiblen Komponenten zuverlässig vor Feuchtigkeit und Schmutz – für eine lange Lebensdauer auch unter Baustellenbedingungen. Durchdachtes Design – innen wie aussen Auch optisch überzeugt der TTK 355 S: Die Technik steckt in einem funktional gestalteten, widerstandsfähigen Gehäuse im markanten Trotec-Industriedesign – formschön, geschützt und praxisorientiert. Der stapelbare Aufbau mit praktischen Nutführungen auf der Oberseite ermöglicht eine platzsparende Lagerung und einen sicheren Transport mehrerer baugleicher Geräte. Ihre Vorteile auf einen Blick: 100 % Trotec – Entwicklung, Design und Fertigung Hohe Entfeuchtungsleistung, auch bei niedrigeren Temperaturen Schutz der Elektronik vor Staub und Feuchtigkeit Wartungsfreundliche Konstruktion Einfaches Handling und flexibler Transport Rollkolbenkompressor: transportabel in jeder Lage Stapelbar für Lagerung und Transport Multistapelfähig mit baugleichen Modellen Integrierter Hitzeschutz für den Kompressor Deutsches Industriedesign mit Geschmacksmusterschutz Sicherer Betrieb bei hoher Wärme- und Feuchtelast Bei der Sanierung von Wasserschäden oder ähnlichen Anwendungen herrschen oft extreme Bedingungen: hohe Luftfeuchte bei gleichzeitig hohen Temperaturen. Dies stellt eine grosse Belastung für Kältetrockner dar. Die sogenannte „35er-Regel“ verdeutlicht die Problematik: Liegt die Raumtemperatur dauerhaft über 35 °C, sinkt die Lebensdauer herkömmlicher Kältetrockner drastisch – auf weniger als 35 %. Ursache ist der steigende Druck im Kältemittelkreislauf, der den Kompressor stark belastet. Zwar arbeiten die Geräte zunächst weiter, sie operieren aber weit über ihrer Belastungsgrenze, was zu vorzeitigem Ausfall führen kann. Adsorptionstrockner stellen unter solchen Bedingungen keine wirtschaftliche Alternative dar – ihr Energiebedarf ist bei vergleichbarer Entfeuchtungsleistung deutlich höher. Intelligente Schutzfunktion serienmässig Deshalb sind die TTK-S-Modelle mit einem intelligenten Kompressor-Hitzeschutz ausgestattet. Sensoren kontrollieren kontinuierlich die Temperaturentwicklung im Gerät. Bei Überhitzung schaltet sich der Kompressor automatisch ab, während der Ventilator weiterläuft. Sobald sich das System wieder im sicheren Temperaturbereich befindet, nimmt der Kompressor selbstständig den Betrieb wieder auf. Dieser Schutzmechanismus verlängert nicht nur die Lebensdauer des Geräts, sondern schützt zugleich die zu trocknenden Materialien und die Gebäudesubstanz vor hitzebedingten Schäden. Entfeuchtungsleistung bei 20 °C / 60 % r.F. 27  Liter / Tag bei 30 °C / 80 % r.F. 55  Liter / Tag Technische Daten Luftmenge Stufe max. 490 m³/h Raumgrösse  140 m² / 350 m³ Temperaturbereich min.  5 - 32 °C Feuchtebereich min.  40 - 90 % r.F. Netzanschluss 220 - 240 V, 50 Hz Nennstromaufnahme 6.1 A Leistungsaufnahme 1.4 kW empfohlene Absicherung 10 A Anschlussstecker EU-Stecker mit Schweizer Fixadapter Kabellänge 3 m Rollkolbenkompressor   Kältemitteltyp R-454C Kältemittelmenge 650 g GWP Faktor 146 CO2 -Äquivalent 0.0949 t Druck Saugseite  0.6 Mpa Druck Austrittseite 2.2 Mpa max. zulässiger Druck 3 Mpa Masse (H x B x T) 725 x 380 x 390 mm Gewicht 39 kg Wassereimer 6  Liter + direkter Schlauchanschluss Schallpegel in Abstand 1 m 54 dB(A) Trotec Artikel-Nr. 1.120.000.163 Garantie 2 Jahre

Learn more More Fewer

The 650S is a robust and powerful construction dryer that stands out for its versatility. It effortlessly handles demanding tasks such as drying after water damage, new construction drying, and maintaining dryness in heated and unheated storage rooms. Manufactured in a specialized European facility, this dehumidifier impresses with its high-quality workmanship and reliable operation. The durable construction of the 650S guarantees a long lifespan, while the easy maintenance and low upkeep costs make operation even more economical. Despite its impressive performance and quality, the 650S is available at an extremely attractive price, making it an excellent choice for professional users.Easy to use The desired target humidity can be continuously regulated between 32 - 100 % using a mechanical hygrostat, and continuous operation is also possible. Particularly useful in larger areas is the high air circulation volume of a substantial 925 cubic meters per hour. With its stable cart construction and large wheels, frequent changes of location can be easily carried out.     Direct hose connection and optional pump kit   Due to its very high dehumidification performance, this dehumidifier has a direct connection for condensate drainage instead of a water tank. The hose must have a slope towards the drain. If this is not possible, a suitable pump kit is optionally available, which can pump the water upwards and also outwards.   The operating switch is protected against dust and splashes by a protective cover, and a slotted hygrostat rotary switch prevents unwanted adjustment of the switch position.     Professional Hot Gas Defrosting   Inside, a professional hot gas defrosting automatic system ensures effective dehumidification results. The fin evaporators unleash their power particularly in temperature ranges above 10°C and in the range above 40% humidity. Technically, the dryer can be used at room temperatures down to about 5°C, even in unattended continuous operation.     Optional counters   Included in delivery is no "Hour or consumption meters are included. You can order them from us upon request (the housing is standardly prepared for retrofitting). You have the choice between a pure hour meter or the combined dual meter, which measures hours and electricity consumption. The meters are MID compliant. Outside of Switzerland, dryers in professional use must already be MID compliant."     Hydrofluoroolefin (R-454C) as an environmentally friendly refrigerant   "Every year, several million tons of environmentally harmful CO2 emissions (greenhouse gases) are released into the air due to synthetic refrigerants. Therefore, the use of alternative refrigerants is one of our most important goals. By using hydrofluoroolefin (R-454C) as a refrigerant, this dehumidifier makes a valuable contribution to climate protection." The natural refrigerant hydrofluoroolefin (R-454C) is an organic compound and belongs to the hydrocarbons. Unlike synthetic refrigerants, the environmentally friendly hydrofluoroolefin (R-454C) has neither ozone depletion potential (ODP=0) nor a significant greenhouse effect (GWP=146).     Advantages at a Glance   • High dehumidification performance even at low temperatures• Robust plastic-coated metal housing• Thanks to the roll piston compressor, it is transportable and storable in any position.• Stable carriage construction• Automatic hygrostat-controlled dehumidification operation• Quality hot gas defrost automatic system• Option to retrofit MID-compliant dual meter for operating and kilowatt hours (optional) • Option to add a suitable pump kit that can be connected directly to the device (optional)     Technical data   dehumidification performanceat 30 °C / 80 % r.H. 91 liters / day Air volume 925 m³/ h Maximum room size 230 m² (550 m³) Minimum room size 4 m² Temperature range 5 - 32°C Moisture range technical Moisture Range Practice 32 - 90 % r.F. 40 - 90 % r.F. voltage 220 - 240 V/50 Hz Nominal current consumption max. 9.5 A Power consumption max. 2100 W Recommended Coverage 16 A Cable length approx. 3 m Plug EU plug with Swiss fixed adapter refrigerant R-454C (1050g) GWP 146 water bucket no bucket, only hose connection suitable hose: 16 mm inner diameter Operating noise 56 dB(A) at 1 m distance53 dB(A) at a distance of 2.5 m Dimensions L x W x H 616 x 511 x 1022 mm (incl. guide bracket) Weight 52 kg Automatic defrosting Heissgas dehumidification automation Hygrostatgesteuert Ventilator axial, single-stage blower Prefilter and Timer no (operation on timer possible) Continuous operation possible and Memory function yes (mechanically stores set values) hose connection yes (no hose included in the delivery) - 16 mm Pump optional available (not included in the delivery) Guarantee 2 years

Learn more More Fewer

The AD40 is versatile and so lightweight that it can be carried like a suitcase. Thanks to the BlueDry® technology, the AD40 dehumidifies consistently and reliably even at low humidity and temperature.serviceThe operation is simple and is carried out via the innovative eDRY® electronics. All control elements are clearly arranged, and all important operating states are accessible at any time. The display shows the target and actual humidity. Operating hours (consumption) can be easily read. The energy consumption is displayed via the additional calibrated energy meter. The control is equipped with a memory function. This means that in the event of a power failure, for example on construction sites, the operation will resume with unchanged settings as soon as the power supply returns.Water bucket or optional pumpThe water collection container (6.8 liters) is easy to remove, carry, and empty. It is located inside, with the water level of the bucket measured by a float. When full, it automatically interrupts operation, and operation automatically restarts when the bucket is replaced. An optional matching pump kit is available, which is versatile and suitable for unattended continuous operation.Robust housingThe housing is easy to clean and can be easily disassembled for any necessary service work. It features a foldable handle. Tie-down straps can be attached on the sides. The secured socket is used for connecting additional devices. Four robust, stable plastic feet for floor placement. Stackable with other Aerial Aercube devices.Characteristics  • Case: made of robust, impact-resistant, and UV-resistant plastic, lightweight. Fixed points for AERCUBE® lashing system. • Cable: integrated cable winder.• Setup: freestanding or mounted on Aercube system (fixation points for AERCUBE lashing system).• Airflow: cross, lateral intake and exhaust.• Air filter: Protects the device from dust.• Fan: 2-stage, energy-efficient EC fan.• Defrosting: Demand-controlled hot gas defrosting.• Condensate pump: Optional pump kit available.• Blue-Dry Technology: For particularly energy-saving operation – even at low humidity and temperatures.• Calibrated energy meter (MID compliant).• Memory Function: After a power interruption, it resumes operation with unchanged settings. Therefore, it is also suitable for operation with, for example, a timer. • Hot gas defrosting: Thanks to automatic self-defrosting, it can also be used in cooler environments.• Suitable for unattended continuous operation.• Custom design: available in all colors and with your logo for larger quantities. All AERCUBE system components are 100% compatible and stackable with each other. Aerial "eDRY®" for efficient air dehumidification"A prerequisite for an economical operation and reduced energy consumption is the optimal coordination of the components and the use of advanced measurement and control technology. With the development of "eDRY", Aerial was able to further improve the user-friendliness and energy efficiency of the AD series. The use of digital precision sensors in conjunction with the eDRY electronics enables very accurate measurement and control of the room humidity."    dehumidification performanceThe dryer can be used thanks to advanced hot gas defrosting over a wide temperature range from +1°C to +34°C, although, as with all condensation dryers, the dehumidifying power decreases in cooler environments. Examples of dehumidification performance and consumption under various (constant) ambient conditions:30°C / 80% r.H = 35.0 Liters / 24h (Power consumption: 520W) 27°C / 60% r.H. = 22.0 Liters / 24h (Power consumption: 430W) 20°C / 60% r.H. = 15.0Liters / 24h (Power consumption: 370W) 10°C / 70% r.H. = 8.0 Liters / 24h (Power consumption: 300W)(r.H.=relative humidity)   Technical data   Tension: 230V / 50Hz Power consumption:  max. 530W Sound pressure level:  1 m distance 57 dB(A) 2.5 m distance 54 dB(A) 3 m distance 53 dB(A) Dehumidification capacity: max. 35.0 liters / day (30°C / 80% r.H) Bucket: Capacity 6.8 liters, Operational interruption due to swimmer Recirculation air volume level 1 / 2: 300 / 400 m³/h refrigerant:   R407C Dimensions (H/W/D):      580 / 390 / 450 mm Weight:    25 Kg Business closure: Digital Ambient temperature: +1°C - +34°C Application area: up to approx. 100 m² Swiss plug:  Yes   hose connection:  Connection fitting for direct hose connection Optional Pump Kit Operating hour meter: Yes Guarantee: 2 years Documents / Downloads   User Manual German

Learn more More Fewer

Drying technology at the latest standard! The 9 series of Aerial construction dryers has been completely developed to meet the needs for use on construction sites, in industry, and for water damage drying. The dryers come standard with a MID-approved kWh meter as well as a non-resettable hour meter. Thanks to the CC 6 control, the devices are compatible with the remote monitoring solution "Simplify," allowing for convenient remote operation monitoring.The AD-935 features both an 8-liter condensate tank and a connection nozzle for direct drainage of the condensate via a hose. Additionally, a suitable pump kit is available, which automatically recognizes the device upon installation. The humid room air is drawn in at the front of the housing, and the dry air is blown out at the back. In the intake area, a reusable industrial filter mat cleans the air and ensures that flying particles do not enter the device.     service   The operation is carried out via the operator panel mounted on the side. With just three buttons, it is comfortable and clear. It displays all important information, and the desired values can be set at the push of a button.• Simple 3-button operation • Color-coded status display of room conditions - red, yellow, green • Complete graphic display, no translation required     High service friendliness   The housing has been designed to be opened with minimal effort. This allows internal components to be easily and quickly cleaned or replaced if necessary.     Features at a glance   • Control unit CC 6 compatible with the remote monitoring solution Simplify• OEM versions available on request (minimum order quantity 50)• The use of standardized components from the Dantherm Group's product portfolio ensures quick access to spare parts.• Integrated interface for accessories (dew point kit and external hygrostat)• Automatic detection of the pump kit• Various drainage options: Standard with Ø15mm hose connection, water tank, and optional pump set• MID-approved kWh meter and non-resettable hour meter as standard• 2-stage fan • Integrated night mode for quieter operation in inhabited rooms• R454C refrigerant, non-toxic and non-flammable, with extremely low GWP (Global Warming Potential)• Large wheels• Telescopic Handle• Stackable• Maintenance and service friendly     dehumidification performance The dryer can be used over a temperature range of +5 °C to +30 °C, with the dehumidifying power decreasing in cooler environments, as is the case with all condensation dryers. Examples of dehumidification performance and consumption under various (constant) environmental conditions:30°C / 80% r.H. = 34.0 liters / 24h (Power consumption: 610 W)20°C / 60% r.H. = 16.5 liters / 24h (Power consumption: 450 W)(r.H.=relative humidity)     Technical data  Tension 230V / 50Hz Power consumption 610 W max. Sound pressure level 2.5 m distance 51 dB(A) dehumidification performance     34 liters/day (30°C / 80% r.H.)  condensate tank Approx. 8 liters   Air volume level 1 / 2 300 / 420 m³/h (Night mode: 300 m³/h)  Compressor Rotary compressor  refrigerant R454C Dimensions (H x W x D)   860 x 392 x 508 mm   Weight 35.4 Kg cessation of operations CC 6-Operating Panel, wireless connection with Simplify remote monitoring possible Ambient temperature ambient humidity 5 °C - 30 °C  30 % r.F. - 90 % r.F. Swiss plug Yes, cable length approx. 5 m   hose connection 15 mm hose inner diameter guarantee 2 years

Learn more More Fewer

Drying technology at the latest standard! The 9 series of Aerial construction dryers has been completely developed to meet the needs for use on construction sites, in industry, and for water damage drying. The dryers come standard with a MID-approved kWh meter as well as a non-resettable hour meter. Thanks to the CC 6 control, the devices are compatible with the remote monitoring solution "Simplify," allowing for convenient remote operation monitoring.The AD-935S features both an 8-liter condensate tank and a connection nozzle for directly draining the condensate via a hose. Additionally, a suitable pump kit is available, which automatically detects the device upon installation. The humid room air is drawn in at the front of the housing, and the dry air is blown out at the back. The air is expelled through two Ø100mm nozzles, which blow the air into the room at a good speed. Air hoses can also be attached to these nozzles if the dry air needs to be directed precisely to a specific location. In the intake area, a reusable industrial filter mat cleans the air and ensures that flying particles do not enter the device.     service   The operation is carried out via the operator panel mounted on the side. With just three buttons, it is comfortable and clear. It displays all important information, and the desired values can be set at the push of a button.• Simple 3-button operation • Color-coded status display of room conditions - red, yellow, green • Complete graphic display, no translation required     High service friendliness   The housing has been designed to be opened with minimal effort. This allows internal components to be easily and quickly cleaned or replaced if necessary.     dehumidification performance The dryer can be used over a temperature range of +5 °C to +30 °C, with the dehumidifying power decreasing in cooler environments, as is the case with all condensation dryers. Examples of dehumidification performance and consumption under various (constant) environmental conditions:30°C / 80% r.H. = 28.0 liters / 24h (Power consumption: 785 W)20°C / 60% r.H. = 13 liters / 24h (Power consumption: 560 W)(r.H.=relative humidity)     Features at a glance   • Control unit CC 6 compatible with the remote monitoring solution Simplify• OEM versions available on request (minimum order quantity 50)• The use of standardized components from the Dantherm Group's product portfolio ensures quick access to spare parts.• Integrated interface for accessories (dew point kit and external hygrostat)• Automatic detection of the pump kit• Various drainage options: Standard with Ø15mm hose connection, water tank, and optional pump set• MID-approved kWh meter and non-resettable hour meter as standard• 1-stage fan • Integrated night mode for quieter operation in inhabited rooms• R454C refrigerant, non-toxic and non-flammable, with extremely low GWP (Global Warming Potential)• Large wheels• Telescopic Handle• Stackable• Equipped with a 1kW electric heating element and 2x Ø100mm duct connections• Maintenance and service friendly     Technical data  Tension 230V / 50Hz Power consumption 785 W max. (1785 W with additional heating) Recording supplementary heating  +1000W  Sound pressure level 2.5 m distance 53 dB(A) dehumidification performance     28 liters/day (30°C / 80% r.H.)  condensate tank Approx. 8 liters   air volume 400 m³/h  Compressor Rotary compressor  refrigerant R454C Dimensions (H x W x D)   860 x 391 x 505 mm   Weight ca. 36 Kg cessation of operations CC 6-Operating Panel, wireless connection with Simplify remote monitoring possible Ambient temperature ambient humidity 5 °C - 30 °C  30 % r.F. - 90 % r.F. Swiss plug Yes, cable length approx. 5 m   hose connection 15 mm hose inner diameter guarantee 2 years

Learn more More Fewer

Drying technology at the latest standard! The 9 series of Aerial construction dryers has been completely developed to meet the needs for use on construction sites, in industry, and for water damage drying. The dryers come standard with a MID-approved kWh meter as well as a non-resettable hour meter. Thanks to the CC 6 control, the devices are compatible with the remote monitoring solution "Simplify," allowing for convenient remote operation monitoring.The AD-955 features both a 13-liter condensate tank and a connection nozzle for directly draining the condensate via a hose. Additionally, a suitable pump kit is available, which automatically recognizes the device upon installation. The humid room air is drawn in at the front of the housing, and the dry air is blown out at the back. In the intake area, a reusable industrial filter mat cleans the air and ensures that flying particles do not enter the device.     service   The operation is carried out via the operator panel mounted on the side. With just three buttons, it is comfortable and clear. It displays all important information, and the desired values can be set at the push of a button.• Simple 3-button operation • Color-coded status display of room conditions - red, yellow, green • Complete graphic display, no translation required     High service friendliness   The housing has been designed to be opened with minimal effort. This allows internal components to be easily and quickly cleaned or replaced if necessary.     Features at a glance   • Control unit CC 6 compatible with the remote monitoring solution Simplify• OEM versions available on request (minimum order quantity 50)• The use of standardized components from the Dantherm Group's product portfolio ensures quick access to spare parts.• Integrated interface for accessories (dew point kit and external hygrostat)• Automatic detection of the pump kit• Various drainage options: Standard with Ø15mm hose connection, water tank, and optional pump set• MID-approved kWh meter and non-resettable hour meter as standard• 2-stage fan • Integrated night mode for quieter operation in inhabited rooms• R454C refrigerant, non-toxic and non-flammable, with extremely low GWP (Global Warming Potential)• Large wheels• Telescopic Handle• Stackable• Maintenance and service friendly     dehumidification performance The dryer can be used over a temperature range of +5 °C to +30 °C, with the dehumidifying power decreasing in cooler environments, as is the case with all condensation dryers. Examples of dehumidification performance and consumption under various (constant) environmental conditions:30°C / 80% r.H. = 53 liters / 24h (Power consumption: 830 W)20°C / 60% r.H. = 22.5 liters / 24h (Power consumption: 560 W)(r.H.=relative humidity)     Technical data  Tension 230V / 50Hz Power consumption 830 W max. Sound pressure level 2.5 m distance 53 dB(A) dehumidification performance     53 liters/day (30°C / 80% r.H.)  condensate tank Approx. 13 liters   Air volume level 1 / 2 290 / 550 m³/h (Night mode: 290 m³/h)  Compressor Rotary compressor  refrigerant R454C Dimensions (H x W x D)   845 x 452 x 538 mm   Weight 41.8 Kg cessation of operations CC 6-Operating Panel, wireless connection with Simplify remote monitoring possible Ambient temperature ambient humidity 5 °C - 30 °C  30 % r.F. - 90 % r.F. Swiss plug Yes, cable length approx. 5 m   hose connection 15 mm hose inner diameter guarantee 2 years

Learn more More Fewer

The Aerial AD 750 is a very powerful, robustly built dehumidifier for construction sites and industry. The strong blower provides a wide-area exchange of moist and dry air. The AD750 features a robust housing made of impact-resistant plastic, stable guide rails, and side wheels for easy mobility on the floor. The dryer can even be pulled over stairs with these wheels. However, when used as a construction site dehumidifier, attention should be paid to the weight; 2 people are required for relocating it between floors or construction scaffolding.The intake of moist air is at the back via easily removable air filters. The dry air is blown out at the front through slanted slats.Characteristics• Fan: Axial fan with aluminum impeller. Fan motor with winding protection.• Compressor: Fully hermetic rotary vane compressor, protected against overload, mounted with vibration damping.• Condenser/Evaporator: made of copper pipes with aluminum fins. Refrigeration circuit made of copper pipe with capillary tube and filter drier. Service connection on the suction side.• Self-defrosting: Automatic hot gas defrost controlled by DryLogic.• Collection container: 12 liters, with automatic full level shut-off.• Hose connection: Fitting (15 mm) for direct condensate drainage.• Hygrostat: Hygrostat rotary knob• operating hour meter• 2 large transport wheels: good mobility thanks to 2 large transport wheels, ergonomically shaped housing.• Stackable  designsThere are two versions of the AD750: with a bucket without a pump or with a pump without a bucket. Please select the desired model. dehumidification performanceThe dryer can be used over a wide temperature range from +3°C to +32°C thanks to its advanced hot gas defrosting, although, as with all condensation dryers, the dehumidifying power decreases in cooler environments. Examples of dehumidification performance and consumption under various (constant) environmental conditions: at 30°C / 80% r.H. = 55.0 liters / day (power consumption: 900 W)at 27°C / 60 % r.H. = 34.1 Liters / Day (Power consumption: 780 W)at 20°C / 60% r.H. = 24.5 liters / day (power consumption: 660 W)at 10°C / 70% r.H. = 14.0 Liters / Day (Power consumption: 560 W)   Technical data Tension: 230V / 50Hz Power consumption:  max. 900W (10A) / 660W (at 20°C/60% r.H.) Sound pressure level:  2.5 m distance 53 dB(A) (manufacturer's specification) Dehumidification capacity: 55 liters/day (30°C / 80% r.H.)  air circulation volume: 710 m³/h (measurement installed) condensate tank: approx. 12 liters Compressor:     Rotary compressor  refrigerant:   R407c (550gr.) Dimensions (H/W/D):      88 x 52 x 49.5 cm Weight:    42 Kg Business closure: Hygrostatrad Ambient temperature: 3°C ~ 32°C (40 - 95% r.H.) Application area: up to 600m³ (temperature-controlled rooms) resp. 400m³ (unheated) Swiss plug:  Yes   hose connection:  Yes Operating hour meter: Yes Guarantee: 2 years

Learn more More Fewer

Drying technology at the latest standard! The 9 series of Aerial construction dryers has been completely developed to meet the needs for use on construction sites, in industry, and for water damage drying. The dryers come standard with a MID-approved kWh meter as well as a non-resettable hour meter. Thanks to the CC 6 control, the devices are compatible with the remote monitoring solution "Simplify," allowing for convenient remote operation monitoring.Due to its high dehumidification performance, the AD-995 is equipped with a water pump as standard. The humid room air is drawn in at the front of the housing, and the dry air is blown out at the back. In the intake area, a reusable industrial filter mat cleans the air and ensures that flying particles do not enter the device.     service   The operation is carried out via the operator panel mounted on the side. With just three buttons, it is comfortable and clear. It displays all important information, and the desired values can be set at the push of a button.• Simple 3-button operation • Color-coded status display of room conditions - red, yellow, green • Complete graphic display, no translation required     High service friendliness   The housing has been designed to be opened with minimal effort. This allows internal components to be easily and quickly cleaned or replaced if necessary.     Features at a glance   • Control unit CC 6 compatible with the remote monitoring solution Simplify• OEM versions available on request (minimum order quantity 50)• The use of standardized components from the Dantherm Group's product portfolio ensures quick access to spare parts.• Integrated interface for accessories (dew point kit and external hygrostat)• Standard equipped with pump set, no bucket• MID-approved kWh meter and non-resettable hour meter as standard• 2-stage fan • Integrated night mode for quieter operation in inhabited rooms• R454C refrigerant, non-toxic and non-flammable, with extremely low GWP (Global Warming Potential)• Large wheels• Telescopic Handle• Maintenance and service friendly     dehumidification performance The dryer can be used over a temperature range of +5 °C to +30 °C, with the dehumidifying power decreasing in cooler environments, as is the case with all condensation dryers. Examples of dehumidification performance and consumption under various (constant) environmental conditions:30°C / 80% r.H. = 95 liters / 24h (Power consumption: 1830 W)20°C / 60% r.H. = 46.5 liters / 24h (Power consumption: 1282 W)(r.H.=relative humidity)     Technical data  Tension 230V / 50Hz Power consumption 1900 W max. Sound pressure level 2.5 m distance 64 dB(A) dehumidification performance     76 liters/day (30°C / 80% r.H.)  water pump standard (no bucket), lift height 4 m Air volume level 1 / 2 750 / 900 m³/h (Night mode: 750 m³/h)  Compressor Rotary compressor  refrigerant R454C Dimensions (H x W x D)   906 x 502 x 547 mm   Weight 58.2 Kg cessation of operations CC 6-Operating Panel, wireless connection with Simplify remote monitoring possible Ambient temperature ambient humidity 5 °C - 30 °C  30 % r.F. - 90 % r.F. Swiss plug Yes, cable length approx. 5 m   hose connection 15 mm hose inner diameter guarantee 2 years

Learn more More Fewer