Space-saving, extendable laundry hangers for wall mounting. This system offers surprisingly much space for drying smaller laundry items on 5 metal bars, each 1.20m wide. Ideal in spatially confined conditions or as a secondary hanging for occasional drying needs.Easy assembly: the system is fully assembled and only needs to be fixed to the wall with 4 screws / dowels (included in the delivery).Space requirement: extended max. 120 x 46 cm from the wall, retracted 120 x 10 cmLoad capacity approx. 12 kgMaterial: Metal rods, white powder-coatedShipping costs for 1 piece Fr. 18.- (this laundry rack is sent exclusively by courier due to the package dimensions). warranty 2 years Technical data   width 120 cmtotal height 17 cmDepth 10-46 cm from wall  

Learn more More Fewer

Complete wall-to-wall laundry line system made of stainless aluminum rails for self-assembly. Affordable, stable design with Dryfix corner rails and pre-assembled sliding rollers. The screws/anchors required for assembly can be ordered free of charge. White plastic-coated wire rope and chrome cable tensioner for optimal load capacity.0.95 m wide (7 lanes) with20 m rope (line length max. 2.70 m)30 m rope (line length max. 4.10 m)40 m rope (line length max. 5.50 m)50 m rope (line length max. 7.00 m)1.15 m wide (8 lanes) with20 m rope (line length max. 2.30 m)30 m rope (line length max. 3.60 m)40 m rope (line length max. 4.85 m)50 m rope (line length max. 6.10 m)Complete wall-to-wall clothesline system for self-assembly.The set consists of:- 2 x support rails made of sturdy aluminum, perforated for wall mounting- Dryfix sliding rollers black (15 cm distance between the lines)- 1 rope tensioner- plasticized wire rope white- Order for free upon request: Dowels and screws for wall mountingTo calculate the correct rope length, you calculate (Room length x number of lanes) + (1 x rail width) + approx. 10 cm for the insertion of the rope end into the rope tensioner.The rollers are pre-assembled on the carrier rails in this package."Laundry line systems from 1m in length will be shipped by courier in any case."  Technical DataWeight Dryfix Alu complete 1.45m widewith 30m rope 2990 gr.with 40m rope 3259 gr.with 50m rope 3500 gr.  

Learn more More Fewer

Dryfix Vario Metal Laundry Line System, 15 cm Line SpacingComplete wall-to-wall laundry line system for self-assembly, can be combined with wall or ceiling brackets and expanded into a wall-to-ceiling or ceiling-to-ceiling system. Pre-assembled sliding rollers. The screws/anchors required for installation can be ordered free of charge upon request. White plastic-coated wire rope and chrome-plated cable tensioner for optimal load capacity.0.78 m wide (6 lanes) with 20 m rope (line length max. 3.20 m)30 m rope (line length max. 4.80 m)40 m rope (line length max. 6.50 m)50 m rope (line length max. 8.20 m)1.08 m wide (8 lanes) with 20 m rope (line length max. 2.35 m)30 m rope (line length max. 3.60 m)40 m rope (line length max. 4.85 m)50 m rope (line length max. 6.10 m)1.23 m wide (9 lanes) with20 m rope (line length max. 2.05 m)30 m rope (line length max. 3.15 m)40 m rope (line length max. 4.25 m)50 m rope (line length max. 5.35 m)  1.53 m wide (11 lanes) with 30 m rope (line length max. 2.55 m)40 m rope (line length max. 3.45 m)50 m rope (line length max. 4.35 m)70 m rope (line length max. 6.20 m)1.83 m wide (13 lanes) with 30 m rope (line length max. 2.15 m)40 m rope (line length max. 2.90 m)50 m rope (line length max. 3.65 m)70 m rope (line length max. 5.20 m)2.28 m wide (16 lanes) with30 m rope (line length max. 1.70 m)40 m rope (line length max. 2.35 m)50 m rope (line length max. 2.95 m)70 m rope (line length max. 4.20 m) "Can be combined with all wall or ceiling supports from Dryfix, Krüger, Lübra. For rail lengths up to 1.53m, two supports per side are sufficient; above that, we recommend 3 supports per side due to the strong cable tension." The set consists of:- 2 x connection rails made of sturdy metal (4mm thick), perforated for wall mounting- Dryfix sliding rollers (15 cm distance between the lines), color selectable: black, yellow, blue- 1 rope tensioner- plasticized wire rope white- on request: free dowels and screws for wall mountingTo calculate the correct rope length, you calculate(Room length x number of lanes) + (1 x rail width) + approx. 10 cm for the insertion of the rope end into the rope tensioner.The rollers are pre-assembled on the carrier rails in this package.Option Montage: If you would like to have the system professionally installed at your location, please request a quote (depending on distance and possibly other items to be installed).Shipping costs for 1 set Fr. 14.- (we only ship this laundry rack via courier due to the package dimensions). Technical data Dryfix Vario Metal complete  0.78m with 20m rope: 6793g with 30m rope: 7013g with 40m rope: 7282gwith 50m rope: 7523g 1.08m with 20m rope: 8019gwith 30m rope: 8239g with 40m rope: 8508g with 50m rope: 8749g with 70m rope: 9257g 1.53m with 30m rope: 11579g with 40m rope: 11848g with 50m rope: 12089gwith 70m rope: 12597g 2.28m with 30m rope: 14093g with 40m rope: 14362g with 50m rope: 14603g with 70m rope: 15111g

Learn more More Fewer

A practical helper in the laundry room at a comfortable working height. Ideal for drying towels, T-shirts, underwear, etc..In contrast to the "Wall" models, the "Fold" is fixed to the wall and its height is not adjustable. However, it can be folded up to save space when not in use.The load capacity is 10 kg. Thus, it can also easily carry a line with dry or tumbled laundry.Characteristics• Wall-mounted laundry hangers, foldable• Fixed to the wall with 4 points• 8 tubes made of anodized aluminum, resistant to time and moisture. Ideal for indoors and outdoors.• High quality at a low price• Made in Italy 100% Dimensions (L x W x H): 60 x 57 x 9 cmTotal length of pipes for hanging laundry: 4.8 meters "Foxydry" is a quality product from Italy and is exclusively available with us in Switzerland.

Learn more More Fewer

Libelle Stewi Clothes Drying RackThe level consists of a solid, foldable aluminum frame and a stand with a wide support. This ensures that the level remains stable even when loaded and extended. The inclination is also flexible; with the optional sunshade, the drying rack quickly turns into a sun umbrella. The version here is the standard model "Libelle", which is available in lengths of 1.50m (Libelle) or 1.65m (Libelle XL), with both models having the same width of 75 cm. Also available as "DH-Libelle" or "DH-Libelle XL" for drop-down ceiling laundry hanging.The Stewi Libelle is delivered pre-assembled in 3 parts, and assembly is very simple and quick. Likewise, you can also fold the Libelle back together quickly with just a few hand movements and store it in a space-saving manner. Advantages:• Height adjustable• Fabric protected from dirt when folded• Drying area tiltable and foldable• Usable with a separate sun canopy as a shade provider (see accessories)• Also available with wall or ceiling mounting (can be lowered up to 110 cm) (see accessories)• All parts can be easily replaced.• Five application possibilitiesExecution:• Stable aluminum construction• Tear-resistant clothesline made of plastic-coated polyester• End parts made of plasticOptional accessoriesSun canopy, turns the laundry drying into sun protectionLike all original Stewis, the dragonfly is also manufactured in Switzerland. 5-year warrantyShipping costs for 1 item: Fr. 12.- (Basis B-Post)   Technical data   Technical data: 150cm Dimensions (H/W/D): 110-175 x 75 x 150 cm Linen: 10 to 1.5 mTotal linen length: 15 mWeight: 7.1 KgWarranty: 2 yearsArticle No. / Color 298 / alu/blue        Technical Data: 165cm Dimensions (H/W/D): 110-175 x 75 x 165 cm Linen: 10 to 1.65 mTotal linen length: 16.5 mWeight: 7.1 KgWarranty: 5 years

Learn more More Fewer

Complete laundry line system for self-assembly with sturdy T-telescopes made of stainless metal. Ideal as a secondary hanging solution or wherever a wall-to-wall solution is not possible due to spatial reasons. This system requires a stable, non-insulated supporting wall, ideally made of concrete or masonry. The supports extend 60 cm into the room and have space for 5 lines.White plasticized wire rope and chrome-plated cable tensioner for optimal load capacity.The set consists of• 2 x T-beams made of sturdy metal, length 60 m. The first line is 14.2 cm away from the wall, then 10 cm distance.• 10 sliding rollers Dryfix, color selectable black, yellow, blue• 1 rope tensioner• plasticized wire rope white 10m• Dowels and screws for wall mountingThe rollers are pre-assembled on the carrier rails in this package.Ideal mounting heightAs a junior line (additional hang) at a comfortable working height (approx. 1m), or as a main hang at approx. 1.85m height.

Learn more More Fewer

Complete laundry line system for self-assembly with sturdy T-telescopes made of stainless metal. Ideal as a secondary hanging solution or wherever a wall-to-wall solution is not possible due to space constraints. This system requires a stable, non-insulated supporting wall, ideally made of concrete or masonry. White plastic-coated wire rope and chrome-plated cable tensioner for optimal load capacity.1 m (8 lanes) with20 m rope - for a width of max. 2.36 m The set consists of- 2 x T-beams made of sturdy metal with a widened mounting plate for ideal stability, length 1 m. The first line is 10 cm away from the wall, then 12.5 cm distance.- 16 sliding rollers Dryfix, color selectable black, yellow, blue- 1 rope tensioner- plasticized wire rope white- 4 dowels and screws for wall mountingThe rollers are pre-assembled on the carrier rails in this package.Ideal mounting heightas main hangs approx. 1.85-1.95m (to avoid injuries, install above head height), or as wide secondary hangs also popular at hip height.Technical data   Material: galvanized metal, rust-freeMass foot: 18 x 18 cm, 4-fold punched (10 mm diameter)Total length from wall: 100 cmDistance of the holes from the wall: 10 / 22.5 / 35 / 47.5 / 60 / 72.5 / 85 / 97.5 cm Compatible with all systems from Dryfix, Krüger, Lübra, and Roth-Kippe.  

Learn more More Fewer

The laundry rack is mounted to the wall with two guide rails. The rack hanging from it with drying rods is connected to a chain system. With this, it can be lifted to any height even when loaded, thanks to the pulley principle, without much effort. The laundry dryer offers space for 6.5 - 12m of laundry, depending on the desired version. The lowering height is a maximum of 1.30 m.The production of the laundry hangers mainly uses high-quality materials such as steel and anodized aluminum, which can withstand frequent use. As a result, the "Wall" is suitable for use in both indoor and outdoor areas. "Foxydry" is a quality product from Italy and is exclusively available with us in Switzerland.

Learn more More Fewer

The laundry rack is mounted to the wall with two guide rails. The rack hanging from it with drying rods is connected to a chain system. With this, it can be lifted to any height even when loaded, thanks to the pulley principle, without much effort. The laundry dryer offers space for 6.5 - 12m of laundry, depending on the desired version. The lowering height is a maximum of 1.30 m.The production of the laundry hangers mainly uses high-quality materials such as steel and anodized aluminum, which can withstand frequent use. As a result, the "Wall" is suitable for use in both indoor and outdoor areas. "Foxydry" is a quality product from Italy and is exclusively available with us in Switzerland.

Learn more More Fewer

The laundry rack is mounted to the wall with two guide rails. The rack hanging from it with drying rods is connected to a chain system. With this, it can be lifted to any height even when loaded, thanks to the pulley principle, without much effort. The laundry dryer offers space for 6.5 - 12m of laundry, depending on the desired version. The lowering height is a maximum of 1.30 m.The production of the laundry hangers mainly uses high-quality materials such as steel and anodized aluminum, which can withstand frequent use. As a result, the "Wall" is suitable for use in both indoor and outdoor areas. "Foxydry" is a quality product from Italy and is exclusively available with us in Switzerland.

Learn more More Fewer

The laundry rack is mounted to the wall with two guide rails. The rack hanging from it with drying rods is connected to a chain system. With this, it can be lifted to any height even when loaded, thanks to the pulley principle, without much effort. The laundry dryer offers space for 6.5 - 12m of laundry, depending on the desired version. The lowering height is a maximum of 1.30 m.The production of the laundry hangers mainly uses high-quality materials such as steel and anodized aluminum, which can withstand frequent use. As a result, the "Wall" is suitable for use in both indoor and outdoor areas. "Foxydry" is a quality product from Italy and is exclusively available with us in Switzerland.

Learn more More Fewer

The Bora 208 from Roth-Kippe is an affordable, well-thought-out dryer for families with children and for households that do not want to dry all their laundry in the tumbler. It dries about 2-3 loads of laundry per day and is available as "Bora208" (without switchable heating) or "Bora208H" (with switchable heating). In the version with heating, the room can be heated to 18°C at the push of a button in cooler environments. In rooms that maintain 18°C or more year-round, the version with heating offers no advantage.service The Bora features a clear, digital control panel that can be set to various languages (German, French, Italian, English). Drying programs:By pressing a button, the drying program can be started. The dehumidifier runs until the laundry is dry and then automatically switches off. The pre-programmed target humidity value of 40% is suitable in most cases, but can otherwise be increased or decreased to any humidity value according to personal preference. Logically, the device operates until it can assume that the laundry is dry. Then it switches off. After a few minutes, it measures again with 1-3 control cycles using pure recirculated air to check whether the humidity value has increased too much, indicating that the laundry may not be completely dry yet. If so, the Bora dries again; if not, it goes into standby. This follow-up check can optimize the drying result, especially in drying rooms with only a small amount of laundry or with garments of varying thickness. Furthermore, the dryer features a general room monitoring system to prevent mold and odors in the basement. The device automatically activates whenever the room humidity exceeds the threshold for mold and odor formation of 60% relative humidity. This humidity level can also be adjusted as desired. Unlike the laundry drying programs, the dryer does not turn off completely in this mode, but only pauses as long as the humidity is appropriate. If the humidity rises again, the drying operation will also resume. Specifically on the Bora: By repeatedly pressing the program button, the start time can be postponed in half-hour increments. This means that you can hang up the laundry during the day, but shift the drying time to the period of the lower electricity tariff.Switchable heating:For a small additional fee, the device is also available as "Bora 208 H". The switchable 1000W heater accelerates the drying of laundry in the cold season because warm air can hold more moisture than cold air. When the heater is switched on, it heats until a room temperature of 18°C is reached. Above 18°C, the heater is inactive, even if it is switched on.  Blower and fan stages:The blower is a radial blower, which is placed in the upper area of the housing. It disperses relatively widely, but loses power in depth (in long drying rooms). The Bora is therefore particularly suitable for shorter to medium laundry hanging of up to about 5m in length, which can certainly have a width of 2m. The warm air stream should blow through the laundry below the clotheslines, so that it can sway in the wind. This causes the moisture to be released more quickly into the room air and can be captured by the dryer. The optimal mounting height of the Boras should therefore be slightly below the lines, which usually means about 1.70m from the top edge of the device.Selectable fan levels: The Boras have a fan level, so on or off.Air louvers: The front of the housing is fixed, meaning the direction of the airflow or the dispersion cannot be changed. Direct hose connection:The water drained from the laundry runs off through a hose connection at the bottom of the housing. The device does not have a built-in pump, so the hose must have a continuous slope to the drain. If no drain is available, the water can of course also be easily collected in a bucket placed under the device. We offer suitable inlet pipes and buckets for all Bora models in our range if needed.Air filter:The humid room air is drawn in at the lower part of the front. An industrial, durable filter mat is inserted in a fold-out door at the bottom. It cleans the air of coarse dust and lint, keeping the inside of the device clean. Should the material of the filter ever be exhausted, suitable replacement filter mats can be ordered from us at any time.Compact dimensions:The Bora is comparatively narrow and often fits into places in the drying room where other devices are too wide, for example between downpipes or electrical lines. Since all operation is done from the front, the Bora does not require any space on the sides or above.  Swiss Control: "Its comfort control was designed by Roth-Kippe and is manufactured in Switzerland. With this, the dryer can be started with a delay if desired, allowing the low-tariff electricity to be fully utilized. This applies both to laundry drying and to the general stabilization of excessive basement humidity. Furthermore, daily blocking times or an automatic, time-limited room drying program - for example, restricted to nighttime hours - can be programmed (limited to a maximum of 99 days each). The device counts the operating hours and reminds you with a light after 300 hours that the filter should be cleaned. By pressing the reset button for 5 seconds, the counter is reset and starts anew."Ambient temperatureTechnically, the "Bora" dryers can be used down to 8°C. Please note that the drying time for all room air dryers increases significantly the colder the room is. For optimal drying speed, temperatures of 15°C and above are ideal. The declared drying performance was measured at a room temperature of 20°C.     Scope of delivery and wall mounting The assembly is very simple, just like with all tumble dryers:A support rail is fixed to the wall with 3 screws, and the Bora can then be easily hung. All necessary mounting materials are already included in the delivery:- the plug-and-play device- Carrier rail with screws/anchors- Hose connection coupling- 2m condensate drain hose- User manual "An optional suitable inlet pipe with bucket is available if the water cannot be directly drained into a drain." Both the support rail and the two buffers supporting the wall in the lower area of the device are insulated with rubber to minimize the transmission of vibrations to the wall. Due to the high dehumidification performance, we recommend draining the condensate directly into the drain with the hose (hose is included in the delivery). If you wish to use a bucket, please ensure that it has sufficient capacity (min. 8 liters) to avoid overflow during the drying process. If wall mounting is not possible, you will find suitable chassis in our range to which the dryer can be mounted.   Assembly service on request   Upon request, we will professionally install the dryer at your home within a radius of up to 120 km (Fr. 210.-), for further distances, price upon request. Calculate distanceImportant:- Sanitary (drainage) or electrical (230V socket) installations are not carried out by us and must be commissioned separately by an appropriate tradesman, unless already in place.- If your wall has internal insulation, we need to know this when placing the order, as the installation will be more complex. The stated installation prices refer to direct wall mounting, meaning directly on brick or concrete walls without insulation. Additional costs for installation on insulated walls will be charged based on effort."If no drainage is available, we recommend the chassis 'Dryfix-Mobil' with integrated bucket or the suitable chassis from Roth-Kippe."  Technical data  drying room: up to 15 m² Drying performance: 1.49 Kg/h Consumption per kg of laundry:   0.31 kWh Energy efficiency: A1 Tension: 230V / 50Hz Examples of dehumidification performance and consumption: Power consumption max. 515W, with heating switched on: +1000W = total 1515W (only 208H) at 20°C / 80% r.H. 22.9 L/24h (Power consumption: 450 W) at 26°C / 80% r.H. 27.5 L/24h (Power consumption: 495 W) Sound pressure level: 1 m distance 70 dB(A) 2.5 m distance 67 dB(A) (our measurement) air circulation volume: 770 m³/h condensate tank: No integrated tank. With hose connection, the water directly drained into the drain or into a bucket. Compressor: Rotary compressor refrigerant: R407C Dimensions (H/W/D): 70.5 x 45 x 33.5 cm Weight: 40 Kg Business closure: Digital Ambient temperature: 8°C ~ 30°C (ideal: 15°C or warmer) Swiss plug: Yes hose connection: Yes Guarantee: 3 years                                               Training video for assembly:    Training video on changing the moisture value:  Training video for changing the display language:  Training video for setting the time:

Learn more More Fewer

From the "Topten" list of the most economical room air dryers: The Dryfix "Swiss" is an excellent dryer for single-family homes with drying rooms up to 15m.² and approx. 40m of clotheslines. It is economical and quieter than room air dryers with comparable drying performance. The elegant, relatively narrow metal housing integrates optimally into the room's appearance. For installation, the support rail is fixed to the wall with two screws, and the dryer can then be easily hung. Rubber buffers prevent the transmission of (very low) vibrations to the wall. The condensate is directed via a hose either directly into a drain or into a bucket placed under the device. The air intake is on the side (right), and the coarse dust filter can be easily pulled out from the front for cleaning.  Drying programs:On the side of the housing is the control. A toggle switch is used to select whether you want the "Drying" mode or "Room Monitoring". A rotary switch can be used to easily adjust the desired residual moisture.Clothes drying: The drying program can be started at the push of a button. The dehumidifier runs until the laundry is dry and then automatically switches off. Room Monitoring: The general room monitoring serves to prevent mold and odors in the basement. The device automatically activates whenever the room humidity exceeds the value set on the dial, with an ideal value for this mode being around 55-60%. Unlike the laundry drying programs, the dryer never completely turns off in this mode, but only pauses as long as the humidity is appropriate. If the humidity rises again, the drying operation will also reactivate.  You can only get the Dryfix Swiss from us! It is exclusively manufactured for our company in a specialized factory in Switzerland.Ambient temperatureTechnically, the "Swiss" tumble dryers can be used down to 5°C. Please note that the drying time for all room air tumble dryers increases significantly the colder the room is. For optimal drying speed, temperatures of 15°C and above are ideal. The declared drying performance was measured at a room temperature of 20°C.  mounting on the wall  The installation is as simple as with all tumble dryers: a mounting rail is anchored to the wall with 2 screws, and the device can then be hung on it. All necessary installation materials such as screws / dowels are included. as well as 1m hose is included in the delivery. Both the support rail and the two buffers supporting the device against the wall at the bottom are rubber insulated to minimize the transmission of vibrations to the wall. Due to the high dehumidification performance, we recommend draining the condensate directly into the drain with the hose if possible. If you wish to use a bucket, please ensure that it has sufficient capacity (min. 8 liters) to avoid overflow during drying. If wall mounting is not possible, you will find suitable chassis in our range to which the dryer can be mounted.   Upon request, we will professionally install the dryer at your home within a radius of up to 120 km (Fr. 210.-), for further distances, price upon request. Calculate distanceImportant:- Sanitary (drainage) or electrical (230V socket) installations are not carried out by us and must be commissioned separately by an appropriate tradesman, unless already in place.- If your wall has internal insulation, we need to know this when placing the order, as the installation will be more complex. The stated installation prices refer to direct wall mounting, meaning directly on brick or concrete walls without insulation. Additional costs for installation on insulated walls will be charged based on effort.   Technical data drying room: up to 15m² Drying performance: 1.73 Kg/h Consumption per kg of laundry: 0.307 kWh Energy efficiency: A1 Tension: 230V / 50Hz Power consumption: 530W Sound pressure level (our measurement): 1.0 m distance 60 dB(A) 2.5 m distance 57 dB(A) Dehumidification capacity: 26 liters/day (30°C / 80% r.H.) air circulation volume: 600m³/h condensate tank: No integrated tank With hose connection, the water directly drained into the drain or into a bucket. Compressor: Rotary compressor Coolant: R410A Dimensions (H/W/D): 55 x 57 x 26 cm (Depth: from wall to front) Weight: 35 Kg    Business closure: Hygrostatrad Ambient temperature: 5°C ~ 30°C Swiss plug: Yes hose connection: Yes Guarantee: 3 years Special features: Made in Switzerland

Learn more More Fewer

The 408 is the ideal solution for households looking for a gentle and energy-efficient alternative to the tumble dryer. It effortlessly handles the drying process of two to three loads of laundry per day, making it perfectly suited to the needs of smaller households. Please note that the model offered here does not have a switchable heating function. As the successor to the proven "Bora 208", the 408 continues to impress with its modern design and compact dimensions, which are identical to its predecessor. However, it has been extensively revised and brought up to date technically. The new, environmentally friendly refrigerant "R32" ensures improved energy efficiency. The ventilation can now be adjusted in three stages, significantly reducing the noise level at the lower fan settings. Additionally, the 408 features a user-friendly touchscreen control and the option for Wi-Fi connectivity, allowing for comfortable control and monitoring.   Operation The Bora features a clear, digital touchscreen control panel that can be set to various languages (German, French, Italian, English). Drying programs:By pressing a button, the drying program can be started. The dehumidifier runs until the laundry is dry and then automatically switches off. The pre-programmed target humidity value of 40% is suitable in most cases, but can otherwise be increased or decreased to any humidity value according to personal preference. Logically, the device operates until it can assume that the laundry is dry. Then it switches off. After a few minutes, it measures again with 1-3 control cycles using pure recirculated air to check whether the humidity value has increased too much, indicating that the laundry may not be completely dry yet. If so, the Bora dries again; if not, it goes into standby. This follow-up check can optimize the drying result, especially in drying rooms with only a small amount of laundry or with garments of varying thickness. Furthermore, the dryer features a general room monitoring system to prevent mold and odors in the basement. The device automatically activates whenever the room humidity exceeds the threshold for mold and odor formation of 60% relative humidity. This moisture level can also be adjusted as desired. Unlike the laundry drying programs, the dryer does not turn off completely in this mode, but only pauses as long as the humidity is appropriate. If the humidity rises again, the drying operation will also resume. Specifically at Bora: The start time can be postponed if, for example, you only want to dry at the low tariff. There are also blocking times possible, during which the device never runs. Furthermore, there is the option for the dryer to automatically switch to room monitoring mode after the laundry drying is completed. Supplementary heating ("H" models):For a small additional charge, the device is also available as "Bora 408 H". The switchable 1000 W heater accelerates the drying of laundry in the cold season because warm air can hold more moisture than cold air. When the heater is switched on, it heats until a room temperature of 18°C is reached. Above 18°C, the heater is inactive, even if it is switched on. Therefore, the version with heating only provides an advantage in rooms that fall below 18°C during the cold season.  Blower and fan stages:The blower is a radial blower, which is placed in the upper area of the housing. It disperses relatively widely, but loses power in depth (in long drying rooms). The Bora is therefore particularly suitable for shorter to medium laundry hanging of up to about 5 m in length, which can certainly have a width of 2 m. The warm air stream should blow through the laundry below the clotheslines, so that it can sway in the wind. This causes the moisture to be released more quickly into the room air and can be captured by the dryer. The optimal mounting height of the Boras should therefore be slightly below the lines, which usually means about 1.70 m from the top edge of the device.Selectable fan speeds: Silent = Gentle / Quiet, consumption and drying time increase slightly. ECO = Consumption and drying speed are within the average range of the specified performance data. Fast = High air throughput for quick, efficient drying. The operating noise is clearly noticeable. Air louvers: The front of the housing is fixed, meaning the direction of the airflow or the dispersion cannot be changed. Direct hose connection:The water drained from the laundry flows out through a hose connection at the bottom of the housing. The device does not have a built-in pump, so the hose must have a continuous slope to the drain. If no drain is available, the water can of course also be easily collected in a bucket placed under the device. We offer suitable inlet pipes and buckets for all Bora models in our range if needed.Air filter:The humid room air is drawn in at the lower part of the front. An industrial, durable filter mat is inserted in a fold-out door at the bottom. It cleans the air of coarse dust and lint, keeping the inside of the device clean. Should the material of the filter ever become exhausted, suitable replacement filter mats can be ordered from us at any time. With the new model, the hold and opening of the door have also been improved with magnets.   WLAN: The WLAN connection allows you to display the BORA status via a browser on your smartphone, tablet, or PC. In addition, the WLAN connection enables you to access software updates. Of course, the operation can also be carried out as usual directly on the device without WLAN. Compact dimensions:The Bora is comparatively narrow and often fits into places in the drying room where other devices are too wide, for example between downpipes or electrical lines. Since all operation is done from the front, the Bora does not require any space on the sides or above.   Swiss Control: "Its comfort control was designed by Roth-Kippe and is manufactured in Switzerland."    Funny gadget: "Anyone who does not want to get used to the new operator panel can switch to the familiar design at the push of a button. The operator panel on the display then looks practically identical to the push buttons of the predecessor model." Ambient temperatureTechnically, the "Bora" dryers can be used down to 8°C. Please note that the drying time for all room air dryers increases significantly the colder the room is. For optimal drying speed, temperatures of 15°C and above are ideal. The declared drying performance was measured at a room temperature of 20°C.     Scope of delivery and wall mounting  The assembly is very simple, as with all tumble dryers:A support rail is fixed to the wall with 3 screws, and the Bora can then be easily hung. All necessary mounting materials are already included in the delivery:• the ready-to-plug-in device• Carrier rail with screws/anchors• Hose connection coupling• 2 m condensate drain hose• Operating instructions   "An optional suitable inlet pipe with bucket is available if the water cannot be directly drained into a drain." Both the support rail and the two buffers supporting the wall in the lower area of the device are insulated with rubber to minimize the transmission of vibrations to the wall. Due to the high dehumidification performance, we recommend draining the condensate directly into the drain with the hose (hose is included in the delivery). If you wish to use a bucket, please ensure that it has sufficient capacity (min. 8 liters) to avoid overflow during drying. If wall mounting is not possible, you will find suitable chassis in our range to which the dryer can be mounted.   Assembly service on request   "Upon request, we will professionally install the dryer at your home within a radius of up to 120 km (Fr. 210.-), for further distances, price upon request." Calculate distanceImportant:- Sanitary (drainage) or electrical (230V socket) installations are not carried out by us and must be commissioned separately by an appropriate tradesman by you, if not already in place.- If your wall has internal insulation, we need to know this when placing the order, as the installation will be more complex. The stated installation prices refer to direct wall mounting, meaning directly on brick or concrete walls without insulation. Additional costs for installation on insulated walls will be charged based on effort."If no chassis is available, we recommend the suitable chassis from Roth-Kippe."  Technical data  Drying room: up to 15 - 18 m² Drying performance: 1.45 - 1.89 kg/h depending on fan speed Consumption per kg of laundry:   0.25 - 0.31 kWh depending on fan speed Energy efficiency: A Tension: 230V / 50Hz Power consumption: in normal operation in "ECO" mode 0.41 kW with heating switched on ("H" models): 1.41 kW Sound pressure level: Fan level 1: 45 dB(A) Fan level 3: 66 dB(A)(Manufacturer's specification at a distance of 3 m) Air circulation volume: that Condensation tank: No integrated tank. With hose connection, the waterdirectly drained into the drain or into a bucket. Compressor: Rotary compressor Refrigerant: R32 (GWP 675) Dimensions (H/W/D): 70.5 x 45 x 33.5 cm Weight: 38 Kg Business closure: Touchscreen Ambient temperature: 8°C ~ 30°C (ideal: 15°C or warmer) Swiss plug: Yes Hose connection: Yes Guarantee: 3 years                                                 Training video for assembly:     

Learn more More Fewer

The new WT230D is a successful evolution of its predecessor model WT230U. It is slightly more powerful in dehumidification performance and is clearly among the best in terms of efficiency with significantly lower consumption. An ideal device for single-family homes in combination with a tumbler.serviceThe easily understandable digital control on the front allows for very simple operation of the device. The display provides current information about the room condition and the selected program. Available display languages include German, French, Italian, and English.Drying programs:Pressing a button starts the drying program. The dehumidifier runs until the laundry is dry and then automatically switches off. With the help of three pre-programmed drying levels, you can choose between damp, iron-damp, or cupboard-dry. All pre-programmed moisture values can be changed at any time according to your own preferences. Furthermore, the dryer features a general room monitoring system to prevent mold and odors in the basement. The device automatically activates whenever the room humidity exceeds the threshold for mold and odor formation of 60% relative humidity. This moisture level can also be adjusted as needed. Unlike the laundry drying programs, the dryer does not turn off completely in this mode, but only pauses as long as the humidity is appropriate. If the humidity rises again, the drying operation will also resume.In both programs, both the current humidity and the target humidity are displayed. Blower and fan stages:The blower is an electronically operated, energy-efficient radial fan. The stream of dry air blows slightly downward from the outlet, meaning that the air is directed into the lower area of the laundry, where the laundry is usually the most damp. This downward air channel is also very practical when placing a drying rack in front of the device.Selectable fan speeds: The WT tumble dryers are the only devices of this kind where the fan speed can be adjusted. Even the lower setting already has a quite respectable air throughput, but significantly reduces the operating noise. If the laundry load is fully packed, the high fan speed is recommended to push the dry air as forcefully as possible through the laundry. This results in faster and more even drying results. At the high setting, the stream of dry air also reaches distant laundry items up to about 7m away.Adjustable air louvers:Flexible slats are installed at the air outlet, which can be adjusted laterally and in height, allowing the air to be more accurately adapted to the length/width of the clotheslines. Direct hose connection:The water extracted from the laundry runs into a hose, which is installed slightly below the middle of the back wall of the WT devices, instead of the usual position at the bottom of the device. This is advantageous compared to other models when the slope to the drain is not very steep or when the device is to be hung slightly lower. The device does not have a built-in pump, so the hose must have a continuous slope to the drain. If no drain is available, the water can of course also be easily collected in a bucket placed under the device. We offer suitable inlet pipes and buckets in our range if needed.Air filter:The humid room air is drawn in at the upper part of the front. A magnetically adhering filter with a frame cleans the air of coarse dust and lint, keeping the inside of the device clean. The filter consists of a very fine, closely woven nylon mesh. This has a high cleaning power, is easy to clean, and typically lasts for the entire lifespan of the dryer with proper care. Memory function:The settings are stored in the room monitoring program. In the event of a power interruption, the WT resumes operation with unchanged settings. It is therefore also suitable for operation with a timer, for example, when you only want to run the dryer during off-peak hours. If the power is interrupted during the laundry drying program, the device goes into standby and must be restarted.Room temperature:Technically, the WT dryers from Aerial can be used down to 8°C. Please note that the drying time for all room air dryers is significantly extended the colder the room is. For optimal drying speed, temperatures of 15°C and above are ideal. The declared drying performance was measured at a room temperature of 20°C. Made in Europe:The WT dryers are manufactured by the Dantherm Group in Europe. They have received very good ratings from the Swiss testing authority for tumble dryers "Swiss Testing." Service-friendly device construction:With just a few simple steps, the entire cover can be removed from the device. This makes handling easier in case of cleaning needs or service work, as the device does not need to be taken off the wall.  mounting on the wall The installation is as simple as with all tumble dryers: a mounting rail is anchored to the wall with 2 screws, and the device can then be hung on it. All necessary installation materials such as screws / dowels are included. as well as 2m hose is included in the delivery. Both the support rail and the two buffers supporting the device against the wall at the lower part are rubber insulated to minimize the transmission of vibrations to the wall. Due to the high dehumidification performance, we recommend draining the condensate directly into the drain with the hose (hose is included in the delivery). If you wish to use a bucket, please ensure that it has sufficient capacity (min. 8 liters) to avoid overflow during drying. If wall mounting is not possible, you will find suitable chassis in our range to which the dryer can be mounted. "Upon request, we will professionally install the dryer at your home within a radius of up to 120 km for Fr. 210.-. For further distances, price upon request."Calculate distanceImportant:• Sanitary (drainage) or electrical (230V socket) installations are not carried out by us and must be commissioned separately by you through an appropriate craftsman, unless already in place.• If your wall has internal insulation, we need to know this when placing the order, as the installation will be more complex. The stated installation prices refer to direct wall installation, meaning directly on brick or concrete walls without insulation. Additional costs for installation on insulated walls will be charged based on effort.  Technical data drying room: up to 18 m² Drying performance: 1.63 Kg/h Consumption per kg of laundry:   0.27 kWh Energy efficiency: A1 Tension: 230V / 50Hz Power consumption: max. 660W or 420W (at 20°C/60% r.H.) Sound pressure level: 2.5 m distance 59 dB(A) 2.5 m distance 67 dB(A) fan level 2 (our measurement) Examples of dehumidification performance and consumption: at 30°C / 80% r.H = 35.5 liters / 24h (power consumption: 569 W) at 27°C / 60% r.H. = 21.1 liters / 24h (power consumption: 487 W) at 20°C / 60% r.H. = 14.6 liters / 24h (power consumption: 420 W) at 10°C / 70% r.H. = 6.1 liters / 24h (power consumption: 368 W) air circulation volume: 750 m³/h condensate tank: No integrated tank. With hose connection, the water directly drained into the drain or into a bucket. Compressor: Rotary compressor refrigerant: R407C Dimensions (H/W/D): 80.9 x 64.0 x 34.5 cm Weight: 40 Kg Business closure: Digital Ambient temperature: 8°C ~ 32°C Swiss plug: Yes hose connection: Yes Guarantee: 3 years

Learn more More Fewer

The 408H is the ideal solution for households looking for a gentle and energy-efficient alternative to the tumble dryer. It effortlessly handles the drying process of two to three loads of laundry per day, making it perfectly suited to the needs of smaller households. Unlike the model 408, the 408H features an optional heating function that further accelerates the drying process when needed. As the successor to the proven "Bora 208H", the 408H impresses with its modern design and compact dimensions, which are identical to its predecessor. However, it has been extensively revised and brought up to date technically. The new, environmentally friendly refrigerant "R32" ensures improved energy efficiency. The ventilation can now be adjusted in three stages, significantly reducing the noise level at the lower fan settings. Additionally, the 408H features a user-friendly touchscreen control and the option for Wi-Fi connectivity, allowing for comfortable control and monitoring.   Operation The Bora features a clear, digital touchscreen control panel that can be set to various languages (German, French, Italian, English). Drying programs:By pressing a button, the drying program can be started. The dehumidifier runs until the laundry is dry and then automatically switches off. The pre-programmed target humidity value of 40% is suitable in most cases, but can otherwise be increased or decreased to any humidity value according to personal preference. Logically, the device operates until it can assume that the laundry is dry. Then it switches off. After a few minutes, it measures again with 1-3 control cycles using pure recirculated air to check whether the humidity value has increased too much, indicating that the laundry may not be completely dry yet. If so, the Bora dries again; if not, it goes into standby. This follow-up check can optimize the drying result, especially in drying rooms with only a small amount of laundry or with garments of varying thickness. Furthermore, the dryer features a general room monitoring system to prevent mold and odors in the basement. The device automatically activates whenever the room humidity exceeds the threshold for mold and odor formation of 60% relative humidity. This moisture level can also be adjusted as needed. Unlike the laundry drying programs, the dryer does not turn off completely in this mode, but only pauses as long as the humidity is appropriate. If the humidity rises again, the drying operation will also resume. Specifically at Bora: The start time can be postponed if, for example, you only want to dry at the low tariff. There are also blocking times possible, during which the device never runs. Furthermore, there is the option for the dryer to automatically switch to room monitoring mode after the laundry drying is completed. Supplementary heating ("H" models):The switchable 1000 W heater accelerates laundry drying in the cold season because warm air can hold more moisture than cold air. When the heater is switched on, it heats until a room temperature of 18°C is reached. Above 18°C, the heater is inactive, even if it is switched on. Therefore, the version with heating only provides an advantage in rooms that fall below 18°C during the cold season.  Blower and fan stages:The blower is a radial blower, which is placed in the upper area of the housing. It disperses relatively widely, but loses power in depth (in long drying rooms). The Bora is therefore particularly suitable for shorter to medium laundry hanging of up to about 5 m in length, which can certainly have a width of 2 m. The warm air stream should blow through the laundry below the clotheslines, so that it can sway in the wind. This causes the moisture to be released more quickly into the room air and can be captured by the dryer. The optimal mounting height of the Boras should therefore be slightly below the lines, which usually means about 1.70 m from the top edge of the device.Selectable fan speeds: Silent = Gentle / Quiet, consumption and drying time increase slightly. ECO = Consumption and drying speed are within the average range of the specified performance data. Fast = High air throughput for quick, efficient drying. The operating noise is clearly noticeable. Air louvers: The front of the housing is fixed, meaning the direction of the airflow or the dispersion cannot be changed. Direct hose connection:The water drained from the laundry flows out through a hose connection at the bottom of the housing. The device does not have a built-in pump, so the hose must have a continuous slope to the drain. If no drain is available, the water can of course also be easily collected in a bucket placed under the device. We offer suitable inlet pipes and buckets for all Bora models in our range if needed.Air filter:The humid room air is drawn in at the lower part of the front. An industrial, durable filter mat is inserted in a fold-out door at the bottom. It cleans the air of coarse dust and lint, keeping the inside of the device clean. Should the material of the filter ever become exhausted, suitable replacement filter mats can be ordered from us at any time. With the new model, the hold and opening of the door have also been improved with magnets.   WLAN: The WLAN connection allows you to display the BORA status via a browser on your smartphone, tablet, or PC. In addition, the WLAN connection enables you to access software updates. Of course, the operation can also be carried out as usual directly on the device without WLAN. Compact dimensions:The Bora is comparatively narrow and often fits into places in the drying room where other devices are too wide, for example between downpipes or electrical lines. Since all operation is done from the front, the Bora does not require any space on the sides or above.   Swiss Control: "Its comfort control was designed by Roth-Kippe and is manufactured in Switzerland."    Funny gadget: "Anyone who does not want to get used to the new operator panel can switch to the familiar design at the push of a button. The operator panel on the display then looks practically identical to the push buttons of the predecessor model." Ambient temperatureTechnically, the "Bora" dryers can be used down to 8°C. Please note that the drying time for all room air dryers increases significantly the colder the room is. For optimal drying speed, temperatures of 15°C and above are ideal. The declared drying performance was measured at a room temperature of 20°C.     Scope of delivery and wall mounting  The assembly is very simple, as with all tumble dryers:A support rail is fixed to the wall with 3 screws, and the Bora can then be easily hung. All necessary mounting materials are already included in the delivery:• the ready-to-plug-in device• Carrier rail with screws/anchors• Hose connection coupling• 2 m condensate drain hose• Operating instructions   "An optional suitable inlet pipe with bucket is available if the water cannot be directly drained into a drain." Both the support rail and the two buffers supporting the wall in the lower area of the device are insulated with rubber to minimize the transmission of vibrations to the wall. Due to the high dehumidification performance, we recommend draining the condensate directly into the drain with the hose (hose is included in the delivery). If you wish to use a bucket, please ensure that it has sufficient capacity (min. 8 liters) to avoid overflow during the drying process. If wall mounting is not possible, you will find suitable chassis in our range to which the dryer can be mounted.   Assembly service on request   "Upon request, we will professionally install the dryer at your home within a radius of up to 120 km (Fr. 210.-), for further distances, price upon request." Calculate distanceImportant:- Sanitary (drainage) or electrical (230V socket) installations are not carried out by us and must be commissioned separately by an appropriate tradesman by you, if not already in place.- If your wall has internal insulation, we need to know this when placing the order, as the installation will be more complex. The stated installation prices refer to direct wall mounting, meaning directly on brick or concrete walls without insulation. Additional costs for installation on insulated walls will be charged based on effort."If no chassis is available, we recommend the suitable chassis from Roth-Kippe."  Technical data  Drying room: up to 15 - 18 m² Drying performance: 1.45 - 1.89 kg/h depending on fan speed Consumption per kg of laundry:   0.25 - 0.31 kWh depending on fan speed Energy efficiency: A Tension: 230V / 50Hz Power consumption: in normal operation in "ECO" mode 0.41 kW with heating switched on ("H" models): 1.41 kW Sound pressure level: Fan level 1: 45 dB(A) Fan level 3: 66 dB(A)(Manufacturer's specification at a distance of 3 m) Air circulation volume: that Condensation tank: No integrated tank. With hose connection, the waterdirectly drained into the drain or into a bucket. Compressor: Rotary compressor Refrigerant: R32 (GWP 675) Dimensions (H/W/D): 70.5 x 45 x 33.5 cm Weight: 38 Kg Business closure: Touchscreen Ambient temperature: 8°C ~ 30°C (ideal: 15°C or warmer) Swiss plug: Yes Hose connection: Yes Guarantee: 3 years                                                 Training video for assembly:     

Learn more More Fewer

The 410 is the ideal solution for family households with children looking for a gentle and energy-efficient alternative to the tumble dryer. It effortlessly handles the drying process of three to four loads of laundry per day, making it perfectly suited to the needs of larger families. Please note that the model offered here does not have a switchable heating function. As the successor to the proven "Bora 210", the 410 impresses with its modern design and compact dimensions, which are identical to its predecessor. However, it has been extensively revised and brought up to date technically. The new, environmentally friendly refrigerant "R32" ensures improved energy efficiency. The ventilation can now be regulated in three stages, significantly reducing the noise level at the lower fan settings. Additionally, the 410 features a user-friendly touchscreen control and the option for Wi-Fi connectivity, allowing for comfortable control and monitoring.   Operation The Bora features a clear, digital touchscreen control panel that can be set to various languages (German, French, Italian, English). Drying programs:By pressing a button, the drying program can be started. The dehumidifier runs until the laundry is dry and then automatically switches off. The pre-programmed target humidity value of 40% is suitable in most cases, but can otherwise be increased or decreased to any humidity value according to personal preference. Logically, the device operates until it can assume that the laundry is dry. Then it switches off. After a few minutes, it measures again with 1-3 control cycles using pure recirculated air to check whether the humidity value has increased too much, indicating that the laundry may not be completely dry yet. If so, the Bora dries again; if not, it goes into standby. This follow-up check can optimize the drying result, especially in drying rooms with only a small amount of laundry or with garments of varying thickness. Furthermore, the dryer features a general room monitoring system to prevent mold and odors in the basement. The device automatically activates whenever the room humidity exceeds the threshold for mold and odor formation of 60% relative humidity. This moisture level can also be adjusted as desired. Unlike the laundry drying programs, the dryer does not turn off completely in this mode, but only pauses as long as the humidity is appropriate. If the humidity rises again, the drying operation will also resume. Specifically at Bora: The start time can be postponed if, for example, you only want to dry at the low tariff. There are also blocking times possible, during which the device never runs. Furthermore, there is the option for the dryer to automatically switch to room monitoring mode after the laundry drying is completed. Supplementary heating ("H" models):For a small additional charge, the device is also available as "Bora 410 H". The switchable 1000 W heater accelerates the drying of laundry in the cold season because warm air can hold more moisture than cold air. When the heater is switched on, it heats until a room temperature of 18°C is reached. Above 18°C, the heater is inactive, even if it is switched on. Therefore, the version with a heater only provides an advantage in rooms that fall below 18°C during the cold season.  Blower and fan stages:The blower is a radial blower, which is placed in the upper area of the housing. It disperses relatively widely, but loses power in depth (in long drying rooms). The Bora is therefore particularly suitable for shorter to medium laundry hanging of up to about 5 m in length, which can certainly have a width of 2 m. The warm air stream should blow through the laundry below the clotheslines, so that it can sway in the wind. This causes the moisture to be released more quickly into the room air and can be captured by the dryer. The optimal mounting height of the Boras should therefore be slightly below the lines, which usually means about 1.70 m from the top edge of the device.Selectable fan speeds: Silent = Gentle / Quiet, consumption and drying time increase slightly. ECO = Consumption and drying speed are within the average range of the specified performance data. Fast = High air throughput for quick, efficient drying. The operating noise is clearly noticeable. Air louvers: The front of the housing is fixed, meaning the direction of the airflow or the dispersion cannot be changed. Direct hose connection:The water drained from the laundry flows out through a hose connection at the bottom of the housing. The device does not have a built-in pump, so the hose must have a continuous slope to the drain. If no drain is available, the water can of course also be easily collected in a bucket placed under the device. We offer suitable inlet pipes and buckets for all Bora models in our range if needed.Air filter:The humid room air is drawn in at the lower part of the front. An industrial, durable filter mat is inserted in a fold-out door at the bottom. It cleans the air of coarse dust and lint, keeping the inside of the device clean. Should the material of the filter ever become exhausted, suitable replacement filter mats can be ordered from us at any time. With the new model, the hold and opening of the door have also been improved with magnets.   WLAN: The WLAN connection allows you to display the BORA status via a browser on your smartphone, tablet, or PC. In addition, the WLAN connection enables you to access software updates. Of course, the operation can also be carried out as usual directly on the device without WLAN. Compact dimensions:The Bora is comparatively narrow and often fits into places in the drying room where other devices are too wide, for example between downpipes or electrical lines. Since all operation is done from the front, the Bora does not require any space on the sides or above.   Swiss Control: "Its comfort control was designed by Roth-Kippe and is manufactured in Switzerland."    Funny gadget: "Anyone who does not want to get used to the new operator panel can switch to the familiar design at the push of a button. The operator panel on the display then looks practically identical to the push buttons of the predecessor model." Ambient temperatureTechnically, the "Bora" dryers can be used down to 8°C. Please note that the drying time for all room air dryers increases significantly the colder the room is. For optimal drying speed, temperatures of 15°C and above are ideal. The declared drying performance was measured at a room temperature of 20°C.     Scope of delivery and wall mounting  The assembly is very simple, as with all tumble dryers:A support rail is fixed to the wall with 3 screws, and the Bora can then be easily hung. All necessary mounting materials are already included in the delivery:• the ready-to-plug-in device• Carrier rail with screws/anchors• Hose connection coupling• 2 m condensate drain hose• Operating instructions   "An optional suitable inlet pipe with bucket is available if the water cannot be directly drained into a drain." Both the support rail and the two buffers supporting the wall in the lower area of the device are insulated with rubber to minimize the transmission of vibrations to the wall. Due to the high dehumidification performance, we recommend draining the condensate directly into the drain with the hose (hose is included in the delivery). If you wish to use a bucket, please ensure that it has sufficient capacity (min. 8 liters) to avoid overflow during the drying process. If wall mounting is not possible, you will find suitable chassis in our range to which the dryer can be mounted.   Assembly service on request   "Upon request, we will professionally install the dryer at your home within a radius of up to 120 km (Fr. 210.-), for further distances, price upon request." Calculate distanceImportant:- Sanitary (drainage) or electrical (230V socket) installations are not carried out by us and must be commissioned separately by an appropriate tradesman by you, if not already in place.- If your wall has internal insulation, we need to know this when placing the order, as the installation will be more complex. The stated installation prices refer to direct wall mounting, meaning directly on brick or concrete walls without insulation. Additional costs for installation on insulated walls will be charged based on effort."If no chassis is available, we recommend the suitable chassis from Roth-Kippe."  Technical data  Drying room: up to 25 m² Drying performance: 1.75 - 2.50 kg/h depending on fan speed Consumption per kg of laundry:   0.22 - 0.28 kWh depending on fan speed Energy efficiency: A Tension: 230V / 50Hz Power consumption: in normal operation in "ECO" mode 0.43 kW with heating switched on ("H" models): 1.43 kW Sound pressure level: Fan level 1: 46 dB(A) Fan level 3: 67 dB(A)(Manufacturer's specification at a distance of 3 m) Air circulation volume: that Condensation tank: No integrated tank. With hose connection, the waterdirectly drained into the drain or into a bucket. Compressor: Rotary compressor Refrigerant: R32 (GWP 675) Dimensions (H/W/D): 70.5 x 45 x 33.5 cm Weight: 40 Kg Business closure: Touchscreen Ambient temperature: 8°C ~ 30°C (ideal: 15°C or warmer) Swiss plug: Yes Hose connection: Yes Guarantee: 3 years                                                 Training video for assembly:     

Learn more More Fewer

The new Secomat2 from Krüger impresses with its intuitive operation and its award-winning design, which has been honored with the prestigious "Reddot" award. As the most compact version of the series, the Secomat2 offers significantly higher drying performance than its predecessor, the Secomat75. It effortlessly handles the drying process of about two loads of laundry per day. The Secomat2 is available in elegant anthracite as well as exclusively from us in stylish azure blue.   Operation   The basic idea of the new generation is that the dryer only needs to be turned on once. After that, the highly developed software and various sensors take over the operation fully automatically. These functions can be selected at the push of a button:Only drying laundry: In this mode, the Secomat4 dries the laundry until it is completely dry. If there is no laundry in the room or if it is already dry, the device automatically pauses.Drying laundry and room monitoring: Here, the Secomat4 first dries the laundry. As soon as it is dry or no laundry is hanging in the room, it automatically switches to room monitoring mode. In this mode, the room air humidity is kept consistently below 60% r.H. to prevent odors and mold formation.Only room monitoring: This mode allows the use of the Secomat4 as a pure room dehumidifier, independent of laundry drying. Here, too, the room air humidity is kept below 60% r.H. to ensure an optimal room climate.   Wi-Fi and app   "Anyone who wants to monitor or change the dryer and its operation can easily do so via the well-developed app on their phone. For this, the device must be within the range of a Wi-Fi network in the house."     Sensors Like most dehumidifiers on the market, the new Secomat models are also equipped with moisture sensors. These measure the room humidity and provide information about the drying process of the laundry. Furthermore, they control the ventilation strength: while very wet laundry releases sufficient moisture even at a low ventilation level, the ventilation is increased the drier the laundry becomes. This is to optimally blow out any remaining moisture from the laundry and to keep the laundry as smooth as possible in the wind.Another sensor is an optical sensor. This sensor remembers the room in an empty state and thus detects when laundry is hanging. When laundry is detected, the device switches to the drying mode. It can distinguish whether the items are statically hung objects (= laundry) or moving objects such as people or animals. Their movement does not trigger the drying process.     Airway and filter   The humid room air is drawn in at the front in the lower area, dried, and then blown back into the room at high speed from the upper area. An air filter cleans the drawn-in air of dirt and fine dust. It is washable and has been significantly improved compared to previous generations. It is now integrated into a solid folding door and is easy to remove.     Water drainage   The drained water is discharged through a hose connection. The connection is located on the bottom of the device near the wall, so that the water runs practically vertically into a siphon mounted below via a hose. With an angle coupling, the water can also be diverted sideways.     Montage   The wall mounting is relatively easy and quick with little craftsmanship. A support rail is fixed to the wall with three screws, and the dryer can then be hung in this support rail. By the way, the support rail of the penultimate generation is compatible, so no new holes need to be drilled. All necessary mounting materials such as rail, screws, dowels, and hose coupling are included in the delivery.     Overview of Features• Environmentally friendly, natural refrigerant R1270• Energy efficient through laundry detection• Intuitive operation• App connectivity• Housing made of powder-coated steel sheet• Adjustable air outlet louvers• Practical procedure set• Easily removable lint filter• Mounting rail for wall installation• 3.5 m power cable• Color: anthracite (RAL 7016)     Technical data  Kruger article: 396.01 Drying room: min. 6 m² up to max. 12 m² Drying performance: 2.13 Kg/h Consumption per kg of laundry:   0.28 kWh Energy efficiency: A Tension: 230V / 50Hz Power consumption: 618W (at 20°C/60% r.H.) Sound pressure level: 64 dB(A) (Manufacturer's specification with 7.5kg laundry in the room) Examples ofdehumidification performanceand consumption: n/a Air circulation volume: n/a Condensation tank: No integrated tank. With hose connection, the waterdirectly drained into the drain or into a bucket. Compressor: Rotary compressor Refrigerant: R1270 / xxxg (GWP: 2) Dimensions (H/W/D): 630 x 512 x 327 mm Weight: 45 Kg Business closure: Program key Ambient temperature: 10 °C ~ 30 °C (our recommendation) 5 °C ~ 30 °C (manufacturer's specification) Swiss plug: Yes Hose connection: Yes Guarantee: 3 years Documents / Downloads   User Manual DE - FR - IT EN

Learn more More Fewer

The new Secomat2 from Krüger impresses with its intuitive operation and its award-winning design, which has been honored with the prestigious "Reddot" award. As the most compact version of the series, the Secomat2 offers a significantly higher drying performance than its predecessor, the Secomat75. It effortlessly handles the drying process of about two loads of laundry per day. The Secomat2 is available in elegant anthracite as well as exclusively from us in stylish azure blue.   Operation   The basic idea of the new generation is that the dryer only needs to be turned on once. After that, the highly developed software and various sensors take over the operation fully automatically. These functions can be selected at the push of a button:Only drying laundry: In this mode, the Secomat4 dries the laundry until it is completely dry. If there is no laundry in the room or if it is already dry, the device automatically pauses.Drying laundry and room monitoring: Here, the Secomat4 first dries the laundry. As soon as it is dry or no laundry is hanging in the room, it automatically switches to room monitoring mode. In this mode, the room air humidity is kept consistently below 60% r.H. to prevent odors and mold formation.Only room monitoring: This mode allows the use of the Secomat4 as a pure room dehumidifier, independent of laundry drying. Here, too, the room air humidity is kept below 60% r.H. to ensure an optimal room climate.   Wi-Fi and app   "Anyone who wants to monitor or change the dryer and its operation can easily do so via the well-developed app on their phone. For this, the device must be within the range of a Wi-Fi network in the house."     Sensors Like most dehumidifiers on the market, the new Secomat devices are also equipped with moisture sensors. These measure the room humidity and provide information about the drying process of the laundry. Furthermore, they control the ventilation strength: while very wet laundry releases sufficient moisture even at a low ventilation level, the ventilation is increased as the laundry dries. This is to optimally blow out the residual moisture from the laundry and to keep the laundry as smooth as possible in the wind.Another sensor is an optical sensor. This sensor remembers the room in an empty state and thus detects when laundry is hanging. When laundry is detected, the device switches to the drying mode. It can distinguish whether the items are statically hung objects (= laundry) or moving objects such as people or animals. Their movement does not trigger the drying process.     Airway and filter   The humid room air is drawn in at the front in the lower area, dried, and then blown back into the room at high speed from the upper area. An air filter cleans the drawn-in air of dirt and fine dust. It is washable and has been significantly improved compared to previous generations. It is now integrated into a solid folding door and is easy to remove.     Water drainage   The drained water is discharged through a hose connection. The connection is located on the bottom of the device near the wall, so that the water runs practically vertically into a siphon mounted below via a hose. With an angle coupling, the water can also be diverted sideways.     Montage   The wall mounting is relatively easy and quick with little craftsmanship. A support rail is fixed to the wall with three screws, and the dryer can then be hung in this support rail. By the way, the support rail of the penultimate generation is compatible, so no new holes need to be drilled. All necessary mounting materials such as rail, screws, dowels, and hose coupling are included in the delivery.     Overview of Features• Environmentally friendly, natural refrigerant R1270• Energy efficient through laundry detection• Intuitive operation• App connectivity• Housing made of powder-coated steel sheet• Adjustable air outlet louvers• Practical procedure set• Easily removable lint filter• Mounting rail for wall installation• 3.5 m power cable• Color: blue (RAL 5009)     Technical data  Kruger article: 396.03 Drying room: min. 6 m² up to max. 12 m² Drying performance: 2.13 Kg/h Consumption per kg of laundry:   0.28 kWh Energy efficiency: A Tension: 230V / 50Hz Power consumption: 618W (at 20°C/60% r.H.) Sound pressure level: 64 dB(A) (Manufacturer's specification with 7.5kg laundry in the room) Examples ofdehumidification performanceand consumption: n/a Air circulation volume: n/a Condensation tank: No integrated tank. With hose connection, the waterdirectly drained into the drain or into a bucket. Compressor: Rotary compressor Refrigerant: R1270 / xxxg (GWP: 2) Dimensions (H/W/D): 630 x 512 x 327 mm Weight: 45 Kg Business closure: Program key Ambient temperature: 10 °C ~ 30 °C (our recommendation) 5 °C ~ 30 °C (manufacturer's specification) Swiss plug: Yes Hose connection: Yes Guarantee: 3 years Documents / Downloads   User Manual DE - FR - IT EN

Learn more More Fewer

The 410H is the ideal solution for family households with children looking for a gentle and energy-efficient alternative to the tumble dryer. It effortlessly handles the drying process of three to four loads of laundry per day, making it perfectly suited to the needs of larger families. The model offered here features an optional heating function that further accelerates the drying process when needed. As the successor to the proven "Bora 210H", the 410H impresses with its modern design and compact dimensions, which are identical to its predecessor. However, it has been extensively revised and brought up to date technically. The new, environmentally friendly refrigerant "R32" ensures improved energy efficiency. The ventilation can now be regulated in three stages, significantly reducing the noise level at the lower fan settings. In addition, the 410H features a user-friendly touchscreen control and the option for Wi-Fi connectivity, allowing for comfortable control and monitoring.   Operation The Bora features a clear, digital touchscreen control panel that can be set to various languages (German, French, Italian, English). Drying programs:By pressing a button, the drying program can be started. The dehumidifier runs until the laundry is dry and then automatically switches off. The pre-programmed target humidity value of 40% is suitable in most cases, but can otherwise be increased or decreased to any humidity value according to personal preference. Logically, the device operates until it can assume that the laundry is dry. Then it switches off. After a few minutes, it measures again with 1-3 control cycles using pure recirculated air to check whether the humidity value has increased too much, indicating that the laundry may not be completely dry yet. If so, the Bora dries again; if not, it goes into standby. Especially in drying rooms with only a small amount of laundry or with garments of varying thickness, this follow-up check can optimize the drying result. Furthermore, the dryer features a general room monitoring system to prevent mold and odors in the basement. The device automatically activates whenever the room humidity exceeds the threshold for mold and odor formation of 60% relative humidity. This humidity level can also be adjusted as needed. Unlike the laundry drying programs, the dryer does not turn off completely in this mode, but only pauses as long as the humidity is appropriate. If the humidity rises again, the drying operation will also resume. Specifically at Bora: The start time can be postponed if, for example, you only want to dry at the low tariff. There are also blocking times possible, during which the device never runs. Furthermore, there is the option for the dryer to automatically switch to room monitoring mode after the laundry drying is completed. Supplementary heating ("H" models):The switchable 1000 W heater accelerates laundry drying in the cold season because warm air can hold more moisture than cold air. When the heater is switched on, it heats until a room temperature of 18°C is reached. Above 18°C, the heater is inactive, even if it is switched on. Therefore, the version with heating only provides an advantage in rooms that fall below 18°C during the cold season.  Blower and fan stages:The blower is a radial blower, which is placed in the upper area of the housing. It spreads relatively wide, but loses power in depth (in long drying rooms). The Bora is therefore particularly suitable for shorter to medium laundry hanging of up to about 5 m in length, which can certainly have a width of 2 m. The warm air stream should blow through the laundry below the clotheslines, so that it can sway in the wind. This causes the moisture to be released to the room air more quickly and can be captured by the dryer. The optimal mounting height of the Boras should therefore be slightly below the lines, which usually means about 1.70 m from the top edge of the device.Selectable fan speeds: Silent = Gentle / Quiet, consumption and drying time increase slightly. ECO = Consumption and drying speed are within the average range of the specified performance data. Fast = High air throughput for quick, efficient drying. The operating noise is clearly noticeable. Air louvers: The front of the housing is fixed, meaning the direction of the airflow or the dispersion cannot be changed. Direct hose connection:The water drained from the laundry flows out through a hose connection at the bottom of the housing. The device does not have a built-in pump, so the hose must have a continuous slope to the drain. If no drain is available, the water can of course also be easily collected in a bucket placed under the device. We offer suitable inlet pipes and buckets for all Bora models in our range if needed.Air filter:The humid room air is drawn in at the lower part of the front. An industrial, durable filter mat is inserted in a fold-out door at the bottom. It cleans the air of coarse dust and lint, keeping the inside of the device clean. Should the material of the filter ever become exhausted, suitable replacement filter mats can be ordered from us at any time. With the new model, the hold and opening of the door have also been improved with magnets.   WLAN: The WLAN connection allows you to display the BORA status via a browser on your smartphone, tablet, or PC. In addition, the WLAN connection enables you to access software updates. Of course, the operation can also be carried out as usual directly on the device without WLAN. Compact dimensions:The Bora is comparatively narrow and often fits into places in the drying room where other devices are too wide, for example between downpipes or electrical lines. Since all operation is done from the front, the Bora does not require any space on the sides or above.   Swiss Control: "Its comfort control was designed by Roth-Kippe and is manufactured in Switzerland."    Funny gadget: "Anyone who does not want to get used to the new operator panel can switch to the familiar design at the push of a button. The operator panel on the display then looks practically identical to the push buttons of the predecessor model." Ambient temperatureTechnically, the "Bora" dryers can be used down to 8°C. Please note that the drying time for all room air dryers increases significantly the colder the room is. For optimal drying speed, temperatures of 15°C and above are ideal. The declared drying performance was measured at a room temperature of 20°C.     Scope of delivery and wall mounting  The assembly is very simple, as with all tumble dryers:A support rail is fixed to the wall with 3 screws, and the Bora can then be easily hung. All necessary mounting materials are already included in the delivery:• the ready-to-plug-in device• Carrier rail with screws/anchors• Hose connection coupling• 2 m condensate drain hose• Operating instructions   "An optional suitable inlet pipe with bucket is available if the water cannot be directly drained into a drain." Both the support rail and the two buffers supporting the wall in the lower area of the device are insulated with rubber to minimize the transmission of vibrations to the wall. Due to the high dehumidification performance, we recommend draining the condensate directly into the drain with the hose (hose is included in the delivery). If you wish to use a bucket, please ensure that it has sufficient capacity (min. 8 liters) to avoid overflow during the drying process. If wall mounting is not possible, you will find suitable chassis in our range to which the dryer can be mounted.   Assembly service on request   "Upon request, we will professionally install the dryer at your home within a radius of up to 120 km (Fr. 210.-), for further distances, price upon request." Calculate distanceImportant:- Sanitary (drainage) or electrical (230V socket) installations are not carried out by us and must be commissioned separately by an appropriate tradesman by you, if not already in place.- If your wall has internal insulation, we need to know this when placing the order, as the installation will be more complex. The stated installation prices refer to direct wall mounting, meaning directly on brick or concrete walls without insulation. Additional costs for installation on insulated walls will be charged based on effort."If no chassis is available, we recommend the suitable chassis from Roth-Kippe."  Technical data  Drying room: up to 25 m² Drying performance: 1.75 - 2.50 kg/h depending on fan speed Consumption per kg of laundry:   0.22 - 0.28 kWh depending on fan speed Energy efficiency: A Tension: 230V / 50Hz Power consumption: in normal operation in "ECO" mode 0.43 kW with heating switched on ("H" models): 1.43 kW Sound pressure level: Fan level 1: 46 dB(A) Fan level 3: 67 dB(A)(Manufacturer's specification at a distance of 3 m) Air circulation volume: that Condensation tank: No integrated tank. With hose connection, the waterdirectly drained into the drain or into a bucket. Compressor: Rotary compressor Refrigerant: R32 (GWP 675) Dimensions (H/W/D): 70.5 x 45 x 33.5 cm Weight: 40 Kg Business closure: Touchscreen Ambient temperature: 8°C ~ 30°C (ideal: 15°C or warmer) Swiss plug: Yes Hose connection: Yes Guarantee: 3 years                                                 Training video for assembly:     

Learn more More Fewer

Those who like their laundry to dry faster will find the WT 240D to be a good and powerful device. The WT240 is the most economical of the new WT series from Aerial. A reliable helper for frequent use in the laundry room.Operation The easily understandable digital control on the front allows for very simple operation of the device. The display provides current information about the room condition and the selected program. Available display languages include German, French, Italian, and English.Drying programs:Pressing a button starts the drying program. The dehumidifier runs until the laundry is dry and then automatically switches off. With the help of three pre-programmed drying levels, you can choose between damp, iron-damp, or cupboard-dry. All pre-programmed moisture values can be changed at any time according to your own preferences. Furthermore, the dryer features a general room monitoring system to prevent mold and odors in the basement. The device automatically activates whenever the room humidity exceeds the threshold for mold and odor formation of 60% relative humidity. This moisture level can also be adjusted as needed. Unlike the laundry drying programs, the dryer does not turn off completely in this mode, but only pauses as long as the humidity is appropriate. If the humidity rises again, the drying operation will also resume.In both programs, both the current humidity and the target humidity are displayed. Blower and fan stages:The blower is an electronically operated, energy-efficient radial fan. The stream of dry air blows slightly downward from the outlet, meaning that the air is directed into the lower area of the laundry, where the laundry is usually the most damp. This downward air channel is also very practical when placing a drying rack in front of the device.Selectable fan speeds: The WT tumble dryers are the only devices of this kind where the fan speed can be adjusted. Even the lower setting already has a quite respectable air throughput, but significantly reduces the operating noise. If the laundry load is fully packed, the high fan speed is recommended to push the dry air as forcefully as possible through the laundry. This results in faster and more even drying results. At the high setting, the stream of dry air also reaches distant laundry items up to about 8m away.Adjustable air louvers:Flexible slats are installed at the air outlet, which can be adjusted laterally and in height, allowing the air to be more accurately adapted to the length/width of the clotheslines. Direct hose connection:The water extracted from the laundry runs into a hose, which is installed slightly below the middle of the back wall of the WT devices, instead of the usual position at the bottom of the device. This is advantageous compared to other models when the slope to the drain is not very steep or when the device is to be hung slightly lower. The device does not have a built-in pump, so the hose must have a continuous slope to the drain. If no drain is available, the water can of course also be easily collected in a bucket placed under the device. We offer suitable inlet pipes and buckets in our range if needed.Air filter:The humid room air is drawn in at the upper part of the front. A magnetically adhering filter with a frame cleans the air of coarse dust and lint, keeping the inside of the device clean. The filter consists of a very fine, closely woven nylon mesh. This has a high cleaning power, is easy to clean, and typically lasts for the entire lifespan of the dryer with proper care. Memory function:The settings are stored in the room monitoring program. In the event of a power interruption, the WT resumes operation with unchanged settings. It is therefore also suitable for operation with a timer, for example, when you only want to run the dryer during off-peak hours. If the power is interrupted during the laundry drying program, the device goes into standby and must be restarted. Room temperature:Technically, the WT dryers from Aerial can be used down to 8°C. Please note that the drying time for all room air dryers is significantly extended the colder the room is. For optimal drying speed, temperatures of 15°C and above are ideal. The declared drying performance was measured at a room temperature of 20°C. Made in Europe:The WT dryers are manufactured by the Dantherm Group in Europe. They have received very good ratings from the Swiss testing authority for tumble dryers "Swiss Testing." Service-friendly device construction:With just a few simple steps, the entire cover can be removed from the device. This makes handling easier in case of cleaning needs or service work, as the device does not need to be taken off the wall.  Mounting on the wall The installation is as simple as with all tumble dryers: a mounting rail is anchored to the wall with 2 screws, and the device can then be hung on it. All necessary installation materials such as screws / dowels are included. as well as a 2m hose is included in the delivery. Both the support rail and the two buffers supporting the device against the wall at the bottom are rubber insulated to minimize the transmission of vibrations to the wall. Due to the high dehumidification performance, we recommend draining the condensate directly into the drain with the hose (hose is included in the delivery). If you wish to use a bucket, please ensure that it has sufficient capacity (min. 8 liters) to avoid overflow during drying. If wall mounting is not possible, you will find suitable chassis in our range to which the dryer can be mounted. Upon request, we will professionally install the dryer at your home within a radius of up to 120 km for Fr. 210.-. For further distances, price upon request. Important:• Sanitary (drainage) or electrical (230V socket) installations are not carried out by us and must be commissioned separately by you through an appropriate craftsman, unless already in place.• If your wall has internal insulation, we need to know this when placing the order, as the installation will be more complex. The stated installation prices refer to direct wall installation, meaning directly on brick or concrete walls without insulation. Additional costs for installation on insulated walls will be charged based on effort.  Technical data drying room: up to 20 m² Drying performance: 1.93 Kg/h Consumption per kg of laundry:   0.26 kWh Energy efficiency: A1 Tension: 230V / 50Hz Power consumption: max. 620W or 440W (at 20°C/60% r.H.) Sound pressure level: 2.5 m distance 62 dB(A) 2.5 m distance 68 dB(A) fan level 2 (our measurement) Examples of dehumidification performance and consumption: at 30°C / 80% r.H = 36.5 L/24h (Power consumption: 570 W) at 27°C / 60% r.H. = 21.6 L/24h (Power consumption: 500 W) at 20°C / 60% r.H. = 16.8 L/24h (power consumption: 440 W) at 10°C / 70% r.H. = 7.2 L/24h (power consumption 390 W) air circulation volume: 830 m³/h condensate tank: No integrated tank. With hose connection, the water directly drained into the drain or into a bucket. Compressor: Rotary compressor refrigerant: R407C Dimensions (H/W/D): 80.9 x 64.0 x 34.5 cm Weight: 40 Kg Business closure: Digital Ambient temperature: 8°C ~ 32°C Swiss plug: Yes hose connection: Yes Guarantee: 3 years

Learn more More Fewer

The new Secomat4 from Krüger impresses with its intuitive operation and well-thought-out functionality. Its modern design, which has been awarded the prestigious "Reddot" award, makes it a real eye-catcher. Designed for single-family homes with higher drying needs or multi-family homes with lower needs, it offers a drying capacity of about three washing machine loads per day. Available in elegant anthracite and exclusively with us also in stylish azure blue.Operation The operation of the Secomat4 is incredibly simple: Once switched on, the advanced software in combination with various sensors takes over the fully automatic operation. At the push of a button, you can choose between three operating modes: Only drying laundry: In this mode, the Secomat4 dries the laundry until it is completely dry. If there is no laundry in the room or if it is already dry, the device automatically pauses.Drying laundry and room monitoring: Here, the Secomat4 first dries the laundry. As soon as it is dry or no laundry is hanging in the room, it automatically switches to room monitoring mode. In this mode, the room air humidity is kept consistently below 60% r.H. to prevent odors and mold formation.Only room monitoring: This mode allows the use of the Secomat4 as a pure room dehumidifier, independent of laundry drying. Here, too, the room air humidity is kept below 60% r.H. to ensure an optimal room climate.   Wi-Fi and app   "Anyone who wants to monitor or change the dryer and its operation can easily do so via the well-developed app on their phone. For this, the device must be within the range of a Wi-Fi network in the house."     Sensors Like most dehumidifiers on the market, the new Secomat models are also equipped with humidity sensors. These measure the room humidity and provide information about the drying process of the laundry. Furthermore, they control the ventilation strength: while very wet laundry releases sufficient moisture even at a low ventilation level, the ventilation is increased as the laundry dries. This is to optimally blow out any remaining moisture from the laundry and to keep the laundry as smooth as possible in the wind.Another sensor is an optical sensor. This sensor remembers the room in an empty state and thus detects when laundry is hanging. When laundry is detected, the device switches to the drying mode. It can distinguish whether the items are statically hung objects (= laundry) or moving objects such as people or animals. Their movement does not trigger the drying process.     Airway and filter   The humid room air is drawn in at the front in the lower area, dried, and then blown back into the room at high speed from the upper area. An air filter cleans the drawn-in air of dirt and fine dust. It is washable and has been significantly improved compared to previous generations. It is now integrated into a solid folding door and is easy to remove.     Water drainage   The drained water is discharged through a hose connection. The connection is located on the bottom of the device near the wall, so that the water runs practically vertically into a siphon mounted below via a hose. With an angle coupling, the water can also be diverted sideways.     Montage   The wall mounting is relatively easy and quick with little craftsmanship. A support rail is fixed to the wall with three screws, and the dryer can then be hung in this support rail. By the way, the support rail of the penultimate generation is compatible, so no new holes need to be drilled. All necessary mounting materials such as rail, screws, dowels, and hose coupling are included in the delivery.     Overview of Features• Environmentally friendly, natural refrigerant R1270• Energy efficient through laundry detection• Intuitive operation• App connectivity• Housing made of powder-coated steel sheet• Adjustable air outlet louvers• Practical procedure set• Easily removable lint filter• Mounting rail for wall installation• 3.5 m power cable• Color: blue (RAL 5009)     Technical data  Kruger article: 397.03 Drying room: min. 6 m² up to max. 16 m² Drying performance: 2.81 Kg/h Consumption per kg of laundry:   0.28 kWh Energy efficiency: A Tension: 230V / 50Hz Power consumption: 618W (at 20°C/60% r.H.) Sound pressure level: 70 dB(A) (Manufacturer's specification for 10kg laundry in the room) Examples ofdehumidification performanceand consumption: n/a Air circulation volume: n/a Condensation tank: No integrated tank. With hose connection, the waterdirectly drained into the drain or into a bucket. Compressor: Rotary compressor Refrigerant: R1270 / xxxg (GWP: 2) Dimensions (H/W/D): 630 x 512 x 327 mm Weight: 45 Kg Business closure: Program key Ambient temperature: 10 °C ~ 30 °C (our recommendation) 5 °C ~ 30 °C (manufacturer's specification) Swiss plug: Yes Hose connection: Yes Guarantee: 3 years Documents / Downloads   User Manual DE - FR - IT EN

Learn more More Fewer

The new "Secomat4" from Krüger impresses with very simple operation and thoughtful functionality. The design has been modernized and even awarded the "Reddot" award. The device is suitable for single-family homes with increased drying frequency or multi-family homes with low drying needs. It achieves a drying performance of about 3 washing machine loads per day. Available in anthracite, and additionally in azure blue with us.  service The basic idea of the new generation is that the dryer only needs to be turned on once. Subsequently, the highly developed software and various sensors take over the operation fully automatically. These functions can be selected at the push of a button:• Only dry laundry: The drying process continues until the laundry is dry. If there is no laundry or if it is dry, the device pauses.• Drying laundry and room monitoring: If laundry is hung, it will be dried. If the laundry is dry or no laundry is hung, the Secomat switches to general room monitoring. The humidity in the room is kept just below the threshold of 60% relative humidity to prevent odors and mold formation.• Only room monitoring: the device can also be used solely as a room dehumidifier, without drying laundry. The humidity in the room is kept just below the threshold of 60% relative humidity to prevent odors and mold formation.  Wi-Fi and app "Anyone who wants to monitor or change the dryer and its operation can easily do so via the well-developed app on their mobile phone. For this, the device must be within the range of a WLAN in the house."  Sensors Like most dehumidifiers on the market, the new Secomat models are also equipped with humidity sensors. These measure the room humidity and provide information about the drying process of the laundry. Furthermore, they control the ventilation strength: while very wet laundry releases sufficient moisture even at a low ventilation level, the ventilation is increased as the laundry dries. This is to optimally blow out any remaining moisture from the laundry and to keep the laundry as smooth as possible in the wind.Another sensor is an optical sensor. This sensor remembers the room in an empty state and thus detects when laundry is hanging. When laundry is detected, the device switches to the drying mode. It can differentiate whether the items are statically hung objects (= laundry) or moving objects such as people or animals. Their movement does not trigger the drying process.  airway and filter The humid room air is drawn in at the front in the lower area, dried, and then blown back into the room at high speed from the upper area. An air filter cleans the drawn-in air of dirt and fine dust. It is washable and has been significantly improved compared to previous generations. It is now integrated into a solid folding door and is easy to remove.  water drainage The drained water is discharged through a hose connection. The connection is located in the bottom of the device near the wall, so that the water runs almost vertically through a hose into a siphon mounted below. With an angle coupling, the water can also be diverted sideways.  Assembly The wall mounting is relatively easy and quick with little craftsmanship. A support rail is fixed to the wall with three screws, and the dryer can then be hung in this support rail. By the way, the support rail of the penultimate generation is compatible, so no new holes need to be drilled. All necessary mounting materials such as rail, screws, dowels, and hose coupling are included in the delivery.   Features at a glance• Environmentally friendly, natural refrigerant R1270• Energy efficient through laundry detection• Intuitive operation• App connectivity• Housing made of powder-coated steel sheet• Adjustable air outlet louvers• Practical procedure set• Easily removable lint filter• Mounting rail for wall installation• 3.5 m power cable• Color: anthracite (RAL 7016)   Technical data  Krüger article: 397.01 drying room: min. 6 m² up to max. 16 m² Drying performance: 2.81 Kg/h Consumption per kg of laundry:   0.28 kWh Energy efficiency: TO Tension: 230V / 50Hz Power consumption: 618W (at 20°C/60% r.H.) Sound pressure level: 70 dB(A) (Manufacturer's specification for 10kg laundry in the room) Examples of dehumidification performance and consumption: n/a air circulation volume: n/a condensate tank: No integrated tank. With hose connection, the water directly drained into the drain or into a bucket. Compressor: Rotary compressor refrigerant: R1270 / xxxg (GWP: 2) Dimensions (H/W/D): 630 x 512 x 327 mm Weight: 45 Kg Business closure: Program key Ambient temperature: 10 °C ~ 30 °C (our recommendation) 5 °C ~ 30 °C (manufacturer's specification) Swiss plug: Yes hose connection: Yes Guarantee: 3 years    Documents / Downloads   User Manual DE - FR - IT EN

Learn more More Fewer

The 415 is a reliable and efficient tumble dryer specifically designed for multi-family homes with up to six units. With a drying time of just four hours for two washing machine loads, depending on the selected fan speed, it effortlessly meets the demands of high-traffic drying rooms. Please note that this model does not have an adjustable heating function. With an energy consumption of only 0.18 kWh per kilogram of laundry, the 415 is the most energy-efficient model in the new Bora series. As the successor to the proven "Bora 315", the 415 impresses with its modern design and compact dimensions, which are identical to its predecessor. However, it has been extensively revised and brought up to date technically. The new, environmentally friendly refrigerant "R32" ensures improved energy efficiency. The ventilation can now be regulated in three stages, significantly reducing the noise level at the lower fan settings. Additionally, the 415 features a user-friendly touchscreen control and the option for Wi-Fi connectivity, allowing for comfortable control and monitoring.   Operation The Bora features a clear, digital touchscreen control panel that can be set to various languages (German, French, Italian, English). Drying programs:By pressing a button, the drying program can be started. The dehumidifier runs until the laundry is dry and then automatically switches off. The pre-programmed target humidity value of 40% is suitable in most cases, but can otherwise be increased or decreased to any humidity value according to personal preference. Logically, the device operates until it can assume that the laundry is dry. Then it switches off. After a few minutes, it measures again with 1-3 control cycles using pure recirculated air to check whether the humidity value has increased too much, indicating that the laundry may not be completely dry yet. If so, the Bora dries again; if not, it goes into standby. This follow-up check can optimize the drying result, especially in drying rooms with only a small amount of laundry or with garments of varying thickness. Furthermore, the dryer features a general room monitoring system to prevent mold and odors in the basement. The device automatically activates whenever the room humidity exceeds the threshold for mold and odor formation of 60% relative humidity. This moisture level can also be adjusted as needed. Unlike the laundry drying programs, the dryer does not turn off completely in this mode, but only pauses as long as the humidity is appropriate. If the humidity rises again, the drying operation will also resume. Specifically at Bora: The start time can be postponed if, for example, you only want to dry at the low tariff. There are also blocking times possible, during which the device never runs. Furthermore, there is the option for the dryer to automatically switch to room monitoring mode after the laundry drying is completed. Supplementary heating ("H" models):For a small additional charge, the device is also available as "Bora 415 H". The switchable 1000 W heater accelerates the drying of laundry in the cold season because warm air can hold more moisture than cold air. When the heater is switched on, it heats until a room temperature of 18°C is reached. Above 18°C, the heater is inactive, even if it is switched on. Therefore, the version with heating only provides an advantage in rooms that fall below 18°C in the cold season.  Blower and fan stages:The blower is a radial blower, which is placed in the upper area of the housing. It disperses relatively widely, but loses power in depth (in long drying rooms). The Bora is therefore particularly suitable for shorter to medium laundry hanging of up to about 5 m in length, which can certainly have a width of 2 m. The warm air stream should blow through the laundry below the clotheslines, so that it can sway in the wind. This causes the moisture to be released more quickly into the room air and can be captured by the dryer. The optimal mounting height of the Boras should therefore be slightly below the lines, which usually means about 1.70 m from the top edge of the device.Selectable fan speeds: Silent = Gentle / Quiet, consumption and drying time increase slightly. ECO = Consumption and drying speed are within the average range of the specified performance data. Fast = High air throughput for quick, efficient drying. The operating noise is clearly noticeable. Air louvers: The front of the housing is fixed, meaning the direction of the airflow or the dispersion cannot be changed. Direct hose connection:The water drained from the laundry flows out through a hose connection at the bottom of the housing. The device does not have a built-in pump, so the hose must have a continuous slope to the drain. If no drain is available, the water can of course also be easily collected in a bucket placed under the device. We offer suitable inlet pipes and buckets for all Bora models in our range if needed.Air filter:The humid room air is drawn in at the lower part of the front. An industrial, durable filter mat is inserted in a fold-out door at the bottom. It cleans the air of coarse dust and lint, keeping the inside of the device clean. Should the material of the filter ever become exhausted, suitable replacement filter mats can be ordered from us at any time. With the new model, the hold and opening of the door have also been improved with magnets.   WLAN: The WLAN connection allows you to display the BORA status via a browser on your smartphone, tablet, or PC. In addition, the WLAN connection enables you to access software updates. Of course, the operation can also be carried out as usual directly on the device without WLAN. Compact dimensions:The Bora is comparatively narrow and often fits into places in the drying room where other devices are too wide, for example between downpipes or electrical lines. Since all operation is done from the front, the Bora does not require any space on the sides or above.   Swiss Control: "Its comfort control was designed by Roth-Kippe and is manufactured in Switzerland."    Funny gadget: "Anyone who does not want to get used to the new operator panel can switch to the familiar design at the push of a button. The operator panel on the display then looks practically identical to the push buttons of the predecessor model." Ambient temperatureTechnically, the "Bora" dryers can be used down to 8°C. Please note that the drying time for all room air dryers increases significantly the colder the room is. For optimal drying speed, temperatures of 15°C and above are ideal. The declared drying performance was measured at a room temperature of 20°C.     Scope of delivery and wall mounting  The assembly is very simple, as with all tumble dryers:A support rail is fixed to the wall with 3 screws, and the Bora can then be easily hung. All necessary mounting materials are already included in the delivery:• the ready-to-plug-in device• Carrier rail with screws/anchors• Hose connection coupling• 2 m condensate drain hose• Operating instructions   "An optional suitable inlet pipe with bucket is available if the water cannot be directly drained into a drain." Both the support rail and the two buffers supporting the wall in the lower area of the device are insulated with rubber to minimize the transmission of vibrations to the wall. Due to the high dehumidification performance, we recommend draining the condensate directly into the drain with the hose (hose is included in the delivery). If you wish to use a bucket, please ensure that it has sufficient capacity (min. 8 liters) to avoid overflow during the drying process. If wall mounting is not possible, you will find suitable chassis in our range to which the dryer can be mounted.   Assembly service on request   "Upon request, we will professionally install the dryer at your home within a radius of up to 120 km (Fr. 210.-), for further distances, price upon request." Calculate distanceImportant:- Sanitary (drainage) or electrical (230V socket) installations are not carried out by us and must be commissioned separately by an appropriate tradesman by you, if not already in place.- If your wall has internal insulation, we need to know this when placing the order, as the installation will be more complex. The stated installation prices refer to direct wall mounting, meaning directly on brick or concrete walls without insulation. Additional costs for installation on insulated walls will be charged based on effort."If no chassis is available, we recommend the suitable chassis from Roth-Kippe."  Technical data  Drying room: up to 30 m² Drying performance: 2.74 - 4.06 kg/h depending on fan speed Consumption per kg of laundry:   0.18 - 0.24 kWh depending on fan speed Energy efficiency: A Tension: 230V / 50Hz Power consumption: in normal operation in "ECO" mode 0.69 kW with heating switched on ("H" models): 1.69 kW Sound pressure level: Fan level 1: 53 dB(A) Fan level 3: 68 dB(A)(Manufacturer's specification at a distance of 3 m) Air circulation volume: that Condensation tank: No integrated tank. With hose connection, the waterdirectly drained into the drain or into a bucket. Compressor: Rotary compressor Refrigerant: R32 (GWP 675) Dimensions (H/W/D): 77 x 70 x 38.5 cm Weight: 62 Kg Business closure: Touchscreen Ambient temperature: 8°C ~ 30°C (ideal: 15°C or warmer) Swiss plug: Yes Hose connection: Yes Guarantee: 3 years                                                 Training video for assembly:     

Learn more More Fewer