Compact adsorption dryer for versatile use in the drying of water damage or for keeping rooms dry with permanent moisture load. The mobile adsorbers of this type are also suitable for industrial applications where low air humidity is required, for example in production facilities.Adsorption dryers have a practically constant dehumidification performance regardless of the room temperature. They are therefore also suitable for use in cold environments, even below freezing point. In principle, the air is passed through a continuously rotating sorption rotor, which is a wheel made of a very moisture-absorbent material. The moisture absorbed by the rotor is expelled from the device by a heated (PTC heating) air stream flowing in the opposite direction (= regeneration air) and must be vented out of the room. The dry air is directed into the room or through hoses to the areas that need to be dried.serviceThe operation is incredibly simple: plug it into the socket, turn on the device with the toggle switch, and set the desired humidity level on the hygrostat. Adjusting the air volumes is not necessary.    Installation of the deviceThe dryer can optionally be placed outside the damp zone or in the room itself:Set up outside the damp area, the dry air is blown into the area to be dried using suitable hoses. The moist exhaust air either enters the room where the dryer is located or can also be discharged using hoses, for example, through a window to the outside. This setup is usually used for drying water damage in cavities, such as water damage under bathtubs or in water pits. When drying water damage in dense materials like underfloor drying, the dry air from the adsorption dryer is additionally pressurized with the help of compressors (e.g., with VP2-6 sound boxes from our range) and can thus be directed to hard-to-reach areas.The arrangement in the room itself is suitable when the entire air volume needs to be kept dry, usually in industrial or commercial applications. The dry air flows directly from the device into the room, while the moist exhaust air is led out of the room via a hose.  Rotor ECODRY G3-MH / PTC Heating ElementThe high-performance rotor is optimized for maximum water intake under varying entry conditions. The mechanical strength of the rotor's surface is extremely high. Non-flammable. The rotor is maintenance-free and washable. Dynamic, safe, and self-regulating PTC heating element.Characteristics • Stackable, quiet, maintenance-friendly • Energy efficient through ecoDRY rotor • Precisely adjustable with built-in hygrostat • Cost and duration control through combination meter for• Operating hours and kWh • Robust stand device with foldable carrying handle • 4 rubber buffers (abrasion-resistant and non-staining) on the underside protect sensitive floor surfaces • Air intake: process and regeneration air together• with air filter and silencer • Housing: Stainless steel / powder-coated steel sheet • Connection cable 4.5 m with power plug • PTC heating elements for maximum operational safety • Optional with calibrated power meterAir Inlet: Common air inlet for process and regeneration air at the front Ø = 125 through silencer and air filter. Air outlet: Dry air: rear side, Ø = 80 mm or 2 x Ø 50 mm, regeneration air: rear side, Ø = 80 mm    Technical data  Tension 1 x 230V / 50 Hz Power consumption 694W max. insurance 10A Sound pressure level 3 m distance 48 dB(A) dehumidification performance 18.75kg/Tag (20°C / 60% r.F.) Liters per kilowatt-hour = 1.13 l/kWh Kilowatt hour per liter = 0.89 kWh/l Airflow Process air volume: 210m³/h Regeneration air volume: 110m³/h Weight   14 Kg Ambient temperature -10°C ~ 35°C  ambient humidity 10 to 100% RH Swiss plug Yes   Guarantee: 2 years

Learn more More Fewer

The medium-sized ASE adsorption dryer from Aerial. Handy yet powerful, making it ideal for flexible use in drying water damage or for keeping rooms dry with permanent moisture exposure. The mobile adsorbers of this type are also suitable for industrial applications where low air humidity is required, for example in production facilities.Adsorption dryers have a practically constant dehumidification performance regardless of the room temperature. They are therefore also suitable for use in cold environments, even below freezing point. In principle, the air is passed through a continuously rotating sorption rotor, which is a wheel made of a very moisture-absorbent material. The moisture absorbed by the rotor is expelled from the device by a heated (PTC heating) air stream flowing in the opposite direction (= regeneration air) and must be vented out of the room. The dry air is directed into the room or through hoses to the areas that need to be dried.serviceThe operation is incredibly simple: plug it into the socket, turn on the device with the toggle switch, and set the desired humidity level on the hygrostat. Adjusting the air volumes is not necessary.    Installation of the deviceThe dryer can optionally be placed outside the damp zone or in the room itself:Set up outside the damp area, the dry air is blown into the area to be dried using suitable hoses. The moist exhaust air either enters the room where the dryer is located or can also be discharged using hoses, for example, through a window to the outside. This setup is usually used for drying water damage in cavities, such as water damage under bathtubs or in water pits. When drying water damage in dense materials like underfloor drying, the dry air from the adsorption dryer is additionally pressurized with the help of compressors (e.g., with VP2-6 sound boxes from our range) and can thus be directed to hard-to-reach areas.The arrangement in the room itself is suitable when the entire air volume needs to be kept dry, usually in industrial or commercial applications. The dry air flows directly from the device into the room, while the moist exhaust air is led out of the room via a hose.  Rotor ECODRY G3-MH / PTC Heating ElementThe high-performance rotor is optimized for maximum water intake under varying entry conditions. The mechanical strength of the rotor's surface is extremely high. Non-flammable. The rotor is maintenance-free and washable. Dynamic, safe, and self-regulating PTC heating element.Characteristics • Stackable, quiet, maintenance-friendly • Energy efficient through ecoDRY rotor • Precisely adjustable with built-in hygrostat • Cost and duration control through combination meter for• Operating hours and kWh • Robust stand device with foldable carrying handle • 4 rubber buffers (abrasion-resistant and non-staining) on the underside protect sensitive floor surfaces • Air intake: process and regeneration air together• with air filter and silencer • Housing: Stainless steel / powder-coated steel sheet • Connection cable 4.5 m with power plug • PTC heating elements for maximum operational safety • Optional with calibrated power meterAir Inlet: Common air inlet for process and regeneration air at the front Ø = 125 through silencer and air filter. Air outlet: Dry air: rear side, Ø = 80 mm or 2 x Ø 50 mm, regeneration air: rear side, Ø = 80 mm     Technical data  Tension 1 x 230V / 50 Hz Power consumption 1040W max. insurance 10A Sound pressure level 3 m distance 57 dB(A) dehumidification performance 25.70kg/Tag (20°C / 60% r.F.) Liters per kilowatt-hour = 1.05 l/kWh Kilowatt hour per liter = 0.97 kWh/l Airflow Process air volumes: 300m³/h Regeneration air volume: 110m³/h Weight 18 Kg dimension 37 x 33.5 x 43 cm (including stubs and stand feet) Ambient temperature -10°C ~ 35°C ambient humidity 10 to 100% RH control panel On/Off switch, built-in hygrostat in the Air intake side, kilowatt-hour meter Swiss plug Yes guarantee 2 years

Learn more More Fewer

The ASE400 demonstrates high reliability in the drying of industrial spaces as well as public and water management facilities. Unlike condensation dryers, adsorbers have a more or less constant dehumidification performance down to well below freezing point. Since the condensate would freeze at these cold temperatures, the extracted moisture is evaporated through a hose and expelled from the room. In water damage drying, the ASE400 is also a powerful device for drying larger areas, ideally in combination with a turbine.Adsorption dryers operate without a compressor. Simply explained, the humid air is passed over a silica gel wheel and divided into dry air and humid air. The dry air is blown into the room but can also be directed via a hose into cavities such as shafts, substructures of bathtubs, etc., or into another device such as a compressor. On the other side of the dryer, the humid air exits, and this can also be discharged via a hose. "Heat is required for this process. The ASE400 features a high-performance rotor that is optimized for maximum water absorption under varying inlet conditions. The mechanical strength of the rotor's surface is extremely high. Non-flammable. The rotor is maintenance-free and washable. Dynamic, safe, and self-regulating PTC heating element."  Air intake rear: through wide air filter (can be removed for cleaning)Air outlet: Dry air front side: Ø = 100 mm, regeneration air back side Ø = 80 mmserviceThe ASE400 is ready to plug in. It has a toggle switch for turning on/off. Optionally, a hygrostat can be connected via the prepared plug to regulate the desired target humidity. The device is suitable for unattended continuous operation. Furthermore, the ASE has an operating hour counter as well as a counter that measures power consumption in kWh. Adjusting the air volumes is not necessary.Characteristics • Stackable, quiet, maintenance-friendly • Energy efficient through ecoDRY rotor • Precisely adjustable with built-in hygrostat • Cost and duration control through combination meter for• Operating hours and kWh • Robust stand device with foldable carrying handle • 4 rubber buffers (abrasion-resistant and non-staining) on the underside protect sensitive floor surfaces • Air intake: process and regeneration air together• with air filter and silencer • Housing: Stainless steel / powder-coated steel sheet • Connection cable 4.5 m with power plug • PTC heating elements for maximum operational safety • Optional with calibrated power meter        Technical data   Tension 1 x 230V / 50 Hz Power consumption 2200W max. insurance 10A Sound pressure level 3 m distance 60 dB(A) dehumidification performance 36kg/day (20°C / 60% r.H.) Liters per kilowatt-hour = 0.75l / kWh Kilowatt hour per liter = 1.33 kWh / l Airflow Process air volumes: 480 m³/h Regeneration air volume: 185 m³/h Weight 25 Kg Dimensions (H x W x D) 410 x 395 x 560 mm Ambient temperature -10°C ~ 35°C ambient humidity 10 to 95% RH control panel on/off switch kilowatt-hour meter Connection option for external control Swiss plug Yes guarantee 2 years

Learn more More Fewer

High-quality rubber plugs for drying water damage under floor coverings and in walls. For all hoses with an inner diameter of 38 or 50 mm. Temperature-resistant SBR quality. The 90° angled shape ensures optimal hose routing on the ground. Perfect grip due to the slightly conical shape of the fitting. Same price for both versions:• 38mm• 50mm 

Learn more More Fewer

High-quality rubber plugs for drying water damage under floor coverings and in walls. For all hoses with an inner diameter of 38 or 50 mm. Temperature-resistant SBR quality. The 90° angled shape ensures optimal hose routing on the ground. Perfect grip due to the slightly conical shape of the fitting. Same price for both versions:• 38mm• 50mm 

Learn more More Fewer

This power distributor records the energy consumption of up to four connected devices using a calibrated energy meter (MID). It was designed to fit the Aerial Aercube drying system and can thus be integrated stacked on it. The CC 4 MID box has been developed for use in construction and water damage drying, offering numerous advantages. The version available for order here is a special version for Switzerland with suitable, standard plugs T12 and sockets T13 (10A).  Features and Benefits   • Extremely robust housing• Protection class IP 44 • Calibrated MID-compliant energy meter• 16 A fuse• residual current device• Number lock included• After installation, there is no access to the internal• More stack sockets possible• Connection of max. 4 consumers• Integrated cable guides in the housing• 4.5 m cable length• Site-compatible power cableFor drying companiesAvailable in your desired color and with your logo upon request.All AERCUBE system components are 100% compatible and stackable with each other.

Learn more More Fewer

Pump Kit for AD 40   Condensate pump (optional accessory) for Aerial dehumidifiers. The pump kit is inserted into the housing at the back instead of the bucket and can be installed and removed with just a few hand movements. The power supply is connected via integrated connectors directly to the socket prepared in the device. Maximum delivery height 4 meters.   Important: the pumps vary in sizing depending on the model. When choosing the pump, pay attention to the correct model. Technical datadischarge head 4m

Learn more More Fewer

The new WT230D is a successful evolution of its predecessor model WT230U. It is slightly more powerful in dehumidification performance and is clearly among the best in terms of efficiency with significantly lower consumption. An ideal device for single-family homes in combination with a tumbler.serviceThe easily understandable digital control on the front allows for very simple operation of the device. The display provides current information about the room condition and the selected program. Available display languages include German, French, Italian, and English.Drying programs:Pressing a button starts the drying program. The dehumidifier runs until the laundry is dry and then automatically switches off. With the help of three pre-programmed drying levels, you can choose between damp, iron-damp, or cupboard-dry. All pre-programmed moisture values can be changed at any time according to your own preferences. Furthermore, the dryer features a general room monitoring system to prevent mold and odors in the basement. The device automatically activates whenever the room humidity exceeds the threshold for mold and odor formation of 60% relative humidity. This moisture level can also be adjusted as needed. Unlike the laundry drying programs, the dryer does not turn off completely in this mode, but only pauses as long as the humidity is appropriate. If the humidity rises again, the drying operation will also resume.In both programs, both the current humidity and the target humidity are displayed. Blower and fan stages:The blower is an electronically operated, energy-efficient radial fan. The stream of dry air blows slightly downward from the outlet, meaning that the air is directed into the lower area of the laundry, where the laundry is usually the most damp. This downward air channel is also very practical when placing a drying rack in front of the device.Selectable fan speeds: The WT tumble dryers are the only devices of this kind where the fan speed can be adjusted. Even the lower setting already has a quite respectable air throughput, but significantly reduces the operating noise. If the laundry load is fully packed, the high fan speed is recommended to push the dry air as forcefully as possible through the laundry. This results in faster and more even drying results. At the high setting, the stream of dry air also reaches distant laundry items up to about 7m away.Adjustable air louvers:Flexible slats are installed at the air outlet, which can be adjusted laterally and in height, allowing the air to be more accurately adapted to the length/width of the clotheslines. Direct hose connection:The water extracted from the laundry runs into a hose, which is installed slightly below the middle of the back wall of the WT devices, instead of the usual position at the bottom of the device. This is advantageous compared to other models when the slope to the drain is not very steep or when the device is to be hung slightly lower. The device does not have a built-in pump, so the hose must have a continuous slope to the drain. If no drain is available, the water can of course also be easily collected in a bucket placed under the device. We offer suitable inlet pipes and buckets in our range if needed.Air filter:The humid room air is drawn in at the upper part of the front. A magnetically adhering filter with a frame cleans the air of coarse dust and lint, keeping the inside of the device clean. The filter consists of a very fine, closely woven nylon mesh. This has a high cleaning power, is easy to clean, and typically lasts for the entire lifespan of the dryer with proper care. Memory function:The settings are stored in the room monitoring program. In the event of a power interruption, the WT resumes operation with unchanged settings. It is therefore also suitable for operation with a timer, for example, when you only want to run the dryer during off-peak hours. If the power is interrupted during the laundry drying program, the device goes into standby and must be restarted.Room temperature:Technically, the WT dryers from Aerial can be used down to 8°C. Please note that the drying time for all room air dryers is significantly extended the colder the room is. For optimal drying speed, temperatures of 15°C and above are ideal. The declared drying performance was measured at a room temperature of 20°C. Made in Europe:The WT dryers are manufactured by the Dantherm Group in Europe. They have received very good ratings from the Swiss testing authority for tumble dryers "Swiss Testing." Service-friendly device construction:With just a few simple steps, the entire cover can be removed from the device. This makes handling easier in case of cleaning needs or service work, as the device does not need to be taken off the wall.  mounting on the wall The installation is as simple as with all tumble dryers: a mounting rail is anchored to the wall with 2 screws, and the device can then be hung on it. All necessary installation materials such as screws / dowels are included. as well as 2m hose is included in the delivery. Both the support rail and the two buffers supporting the device against the wall at the lower part are rubber insulated to minimize the transmission of vibrations to the wall. Due to the high dehumidification performance, we recommend draining the condensate directly into the drain with the hose (hose is included in the delivery). If you wish to use a bucket, please ensure that it has sufficient capacity (min. 8 liters) to avoid overflow during drying. If wall mounting is not possible, you will find suitable chassis in our range to which the dryer can be mounted. "Upon request, we will professionally install the dryer at your home within a radius of up to 120 km for Fr. 210.-. For further distances, price upon request."Calculate distanceImportant:• Sanitary (drainage) or electrical (230V socket) installations are not carried out by us and must be commissioned separately by you through an appropriate craftsman, unless already in place.• If your wall has internal insulation, we need to know this when placing the order, as the installation will be more complex. The stated installation prices refer to direct wall installation, meaning directly on brick or concrete walls without insulation. Additional costs for installation on insulated walls will be charged based on effort.  Technical data drying room: up to 18 m² Drying performance: 1.63 Kg/h Consumption per kg of laundry:   0.27 kWh Energy efficiency: A1 Tension: 230V / 50Hz Power consumption: max. 660W or 420W (at 20°C/60% r.H.) Sound pressure level: 2.5 m distance 59 dB(A) 2.5 m distance 67 dB(A) fan level 2 (our measurement) Examples of dehumidification performance and consumption: at 30°C / 80% r.H = 35.5 liters / 24h (power consumption: 569 W) at 27°C / 60% r.H. = 21.1 liters / 24h (power consumption: 487 W) at 20°C / 60% r.H. = 14.6 liters / 24h (power consumption: 420 W) at 10°C / 70% r.H. = 6.1 liters / 24h (power consumption: 368 W) air circulation volume: 750 m³/h condensate tank: No integrated tank. With hose connection, the water directly drained into the drain or into a bucket. Compressor: Rotary compressor refrigerant: R407C Dimensions (H/W/D): 80.9 x 64.0 x 34.5 cm Weight: 40 Kg Business closure: Digital Ambient temperature: 8°C ~ 32°C Swiss plug: Yes hose connection: Yes Guarantee: 3 years

Learn more More Fewer

Those who like their laundry to dry faster will find the WT 240D to be a good and powerful device. The WT240 is the most economical of the new WT series from Aerial. A reliable helper for frequent use in the laundry room.Operation The easily understandable digital control on the front allows for very simple operation of the device. The display provides current information about the room condition and the selected program. Available display languages include German, French, Italian, and English.Drying programs:Pressing a button starts the drying program. The dehumidifier runs until the laundry is dry and then automatically switches off. With the help of three pre-programmed drying levels, you can choose between damp, iron-damp, or cupboard-dry. All pre-programmed moisture values can be changed at any time according to your own preferences. Furthermore, the dryer features a general room monitoring system to prevent mold and odors in the basement. The device automatically activates whenever the room humidity exceeds the threshold for mold and odor formation of 60% relative humidity. This moisture level can also be adjusted as needed. Unlike the laundry drying programs, the dryer does not turn off completely in this mode, but only pauses as long as the humidity is appropriate. If the humidity rises again, the drying operation will also resume.In both programs, both the current humidity and the target humidity are displayed. Blower and fan stages:The blower is an electronically operated, energy-efficient radial fan. The stream of dry air blows slightly downward from the outlet, meaning that the air is directed into the lower area of the laundry, where the laundry is usually the most damp. This downward air channel is also very practical when placing a drying rack in front of the device.Selectable fan speeds: The WT tumble dryers are the only devices of this kind where the fan speed can be adjusted. Even the lower setting already has a quite respectable air throughput, but significantly reduces the operating noise. If the laundry load is fully packed, the high fan speed is recommended to push the dry air as forcefully as possible through the laundry. This results in faster and more even drying results. At the high setting, the stream of dry air also reaches distant laundry items up to about 8m away.Adjustable air louvers:Flexible slats are installed at the air outlet, which can be adjusted laterally and in height, allowing the air to be more accurately adapted to the length/width of the clotheslines. Direct hose connection:The water extracted from the laundry runs into a hose, which is installed slightly below the middle of the back wall of the WT devices, instead of the usual position at the bottom of the device. This is advantageous compared to other models when the slope to the drain is not very steep or when the device is to be hung slightly lower. The device does not have a built-in pump, so the hose must have a continuous slope to the drain. If no drain is available, the water can of course also be easily collected in a bucket placed under the device. We offer suitable inlet pipes and buckets in our range if needed.Air filter:The humid room air is drawn in at the upper part of the front. A magnetically adhering filter with a frame cleans the air of coarse dust and lint, keeping the inside of the device clean. The filter consists of a very fine, closely woven nylon mesh. This has a high cleaning power, is easy to clean, and typically lasts for the entire lifespan of the dryer with proper care. Memory function:The settings are stored in the room monitoring program. In the event of a power interruption, the WT resumes operation with unchanged settings. It is therefore also suitable for operation with a timer, for example, when you only want to run the dryer during off-peak hours. If the power is interrupted during the laundry drying program, the device goes into standby and must be restarted. Room temperature:Technically, the WT dryers from Aerial can be used down to 8°C. Please note that the drying time for all room air dryers is significantly extended the colder the room is. For optimal drying speed, temperatures of 15°C and above are ideal. The declared drying performance was measured at a room temperature of 20°C. Made in Europe:The WT dryers are manufactured by the Dantherm Group in Europe. They have received very good ratings from the Swiss testing authority for tumble dryers "Swiss Testing." Service-friendly device construction:With just a few simple steps, the entire cover can be removed from the device. This makes handling easier in case of cleaning needs or service work, as the device does not need to be taken off the wall.  Mounting on the wall The installation is as simple as with all tumble dryers: a mounting rail is anchored to the wall with 2 screws, and the device can then be hung on it. All necessary installation materials such as screws / dowels are included. as well as a 2m hose is included in the delivery. Both the support rail and the two buffers supporting the device against the wall at the bottom are rubber insulated to minimize the transmission of vibrations to the wall. Due to the high dehumidification performance, we recommend draining the condensate directly into the drain with the hose (hose is included in the delivery). If you wish to use a bucket, please ensure that it has sufficient capacity (min. 8 liters) to avoid overflow during drying. If wall mounting is not possible, you will find suitable chassis in our range to which the dryer can be mounted. Upon request, we will professionally install the dryer at your home within a radius of up to 120 km for Fr. 210.-. For further distances, price upon request. Important:• Sanitary (drainage) or electrical (230V socket) installations are not carried out by us and must be commissioned separately by you through an appropriate craftsman, unless already in place.• If your wall has internal insulation, we need to know this when placing the order, as the installation will be more complex. The stated installation prices refer to direct wall installation, meaning directly on brick or concrete walls without insulation. Additional costs for installation on insulated walls will be charged based on effort.  Technical data drying room: up to 20 m² Drying performance: 1.93 Kg/h Consumption per kg of laundry:   0.26 kWh Energy efficiency: A1 Tension: 230V / 50Hz Power consumption: max. 620W or 440W (at 20°C/60% r.H.) Sound pressure level: 2.5 m distance 62 dB(A) 2.5 m distance 68 dB(A) fan level 2 (our measurement) Examples of dehumidification performance and consumption: at 30°C / 80% r.H = 36.5 L/24h (Power consumption: 570 W) at 27°C / 60% r.H. = 21.6 L/24h (Power consumption: 500 W) at 20°C / 60% r.H. = 16.8 L/24h (power consumption: 440 W) at 10°C / 70% r.H. = 7.2 L/24h (power consumption 390 W) air circulation volume: 830 m³/h condensate tank: No integrated tank. With hose connection, the water directly drained into the drain or into a bucket. Compressor: Rotary compressor refrigerant: R407C Dimensions (H/W/D): 80.9 x 64.0 x 34.5 cm Weight: 40 Kg Business closure: Digital Ambient temperature: 8°C ~ 32°C Swiss plug: Yes hose connection: Yes Guarantee: 3 years

Learn more More Fewer

The WT 250D is suitable not only for intensive drying tasks in single-family operations but also meets performance expectations in drying rooms shared by multiple parties. With a drying capacity of approximately 3 kg of laundry per hour, this model dries in about 2.5 hours, which is what a washing machine can wash.serviceThe easily understandable digital control on the front allows for very simple operation of the device. The display provides current information about the room condition and the selected program. Available display languages include German, French, Italian, and English.Drying programs:Pressing a button starts the drying program. The dehumidifier runs until the laundry is dry and then automatically switches off. With the help of three pre-programmed drying levels, you can choose between damp, iron-damp, or cupboard-dry. All pre-programmed moisture values can be changed at any time according to your own preferences. Furthermore, the dryer features a general room monitoring system to prevent mold and odors in the basement. The device automatically activates whenever the room humidity exceeds the threshold for mold and odor formation of 60% relative humidity. This moisture level can also be adjusted as needed. Unlike the laundry drying programs, the dryer does not turn off completely in this mode, but only pauses as long as the humidity is appropriate. If the humidity rises again, the drying operation will also resume.In both programs, both the current humidity and the target humidity are displayed. Blower and fan stages:The blower is an electronically operated, energy-efficient radial fan. The stream of dry air blows slightly downward from the outlet, meaning that the air is directed into the lower area of the laundry, where the laundry is usually the most damp. This downward air channel is also very practical when placing a drying rack in front of the device.Selectable fan speeds: The WT tumble dryers are the only devices of this kind where the fan speed can be adjusted. Even the lower setting already has a quite respectable air throughput, but significantly reduces the operating noise. If the laundry load is fully packed, the high fan speed is recommended to push the dry air as forcefully as possible through the laundry. This results in faster and more even drying results. At the high setting, the stream of dry air also reaches distant laundry items up to about 9m away.Adjustable air louvers:Flexible slats are installed at the air outlet, which can be adjusted laterally and in height, allowing the air to be more accurately adapted to the length/width of the clotheslines. Direct hose connection:The water extracted from the laundry runs into a hose, which is installed slightly below the middle of the back wall of the WT devices, instead of the usual position at the bottom of the device. This is advantageous compared to other models when the slope to the drain is not very steep or when the device is to be hung slightly lower. The device does not have a built-in pump, so the hose must have a continuous slope to the drain. If no drain is available, the water can of course also be easily collected in a bucket placed under the device. We offer suitable inlet pipes and buckets in our range if needed.Air filter:The humid room air is drawn in at the upper part of the front. A magnetically adhering filter with a frame cleans the air of coarse dust and lint, keeping the inside of the device clean. The filter consists of a very fine, closely woven nylon mesh. This has a high cleaning power, is easy to clean, and typically lasts for the entire lifespan of the dryer with proper care. Memory function:The settings are stored in the room monitoring program. In the event of a power interruption, the WT resumes operation with unchanged settings. It is therefore also suitable for operation with a timer, for example, when you only want to run the dryer during off-peak hours. If the power is interrupted during the laundry drying program, the device goes into standby and must be restarted. Room temperature:Technically, the WT dryers from Aerial can be used down to 8°C. Please note that the drying time for all room air dryers is significantly extended the colder the room is. For optimal drying speed, temperatures of 15°C and above are ideal. The declared drying performance was measured at a room temperature of 20°C. Made in Europe:The WT dryers are manufactured by the Dantherm Group in Europe. They have received very good ratings from the Swiss testing authority for tumble dryers "Swiss Testing." Service-friendly device construction:With just a few simple steps, the entire cover can be removed from the device. This makes handling easier in case of cleaning needs or service work, as the device does not need to be taken off the wall.  mounting on the wall The installation is as simple as with all tumble dryers: a mounting rail is anchored to the wall with 2 screws, and the device can then be hung on it. All necessary installation materials such as screws / dowels are included. as well as 2m hose is included in the delivery. Both the support rail and the two buffers supporting the device against the wall at the bottom are rubber insulated to minimize the transmission of vibrations to the wall. Due to the high dehumidification performance, we recommend draining the condensate directly into the drain with the hose (hose is included in the delivery). If you wish to use a bucket, please ensure that it has sufficient capacity (min. 8 liters) to avoid overflow during drying. If wall mounting is not possible, you will find suitable chassis in our range to which the dryer can be mounted. "Upon request, we will professionally install the dryer at your home within a radius of up to 120 km for Fr. 210.-. For further distances, price upon request."Calculate distanceImportant:• Sanitary (drainage) or electrical (230V socket) installations are not carried out by us and must be commissioned separately by you through an appropriate craftsman, unless already in place.• If your wall has internal insulation, we need to know this when placing the order, as the installation will be more complex. The stated installation prices refer to direct wall installation, meaning directly on brick or concrete walls without insulation. Additional costs for installation on insulated walls will be charged based on effort.  Technical data drying room: up to 35 m² Drying performance: 2.95 Kg/h Consumption per kg of laundry:   0.27 kWh Energy efficiency: A1 Tension: 230V / 50Hz Power consumption: max. 950W or 677W (at 20°C/60% r.H.) Sound pressure level: 2.5 m distance 61 dB(A) 2.5 m distance 68 dB(A) fan level 2 (our measurement) Examples of dehumidification performance and consumption: at 30°C / 80% r.H = 57.1 Ll/24h (Power consumption: 570 W) at 27°C / 60% r.H. = 24.1 L/24h (Power consumption: 500 W) at 20°C / 60% r.H. = 23.0 L/24h (Power consumption: 440 W) at 10°C / 70% r.H. = 13.4 L/24h (Power consumption: 390 W) air circulation volume: 950 m³/h condensate tank: No integrated tank. With hose connection, the water directly drained into the drain or into a bucket. Compressor: Rotary compressor refrigerant: R407C Dimensions (H/W/D): 80.9 x 64.0 x 34.5 cm Weight: 42 Kg Business closure: Digital Ambient temperature: 8°C ~ 32°C Swiss plug: Yes hose connection: Yes Guarantee: 3 years

Learn more More Fewer

The heavy-duty worker among the new Aerial WT dryers! It is specially designed for intensive use and dries laundry quickly and reliably with easy operation. With a drying capacity of approximately 3.6 kg of laundry per hour, this model dries in about 2 hours what a washing machine can wash.serviceThe easily understandable digital control on the front allows for very simple operation of the device. The display provides current information about the room condition and the selected program. Available display languages include German, French, Italian, and English.Drying programs:Pressing a button starts the drying program. The dehumidifier runs until the laundry is dry and then automatically switches off. With the help of three pre-programmed drying levels, you can choose between damp, iron-damp, or cupboard-dry. All pre-programmed moisture values can be changed at any time according to your own preferences. Furthermore, the dryer features a general room monitoring system to prevent mold and odors in the basement. The device automatically activates whenever the room humidity exceeds the threshold for mold and odor formation of 60% relative humidity. This humidity level can also be adjusted as desired. Unlike the laundry drying programs, the dryer does not turn off completely in this mode, but only pauses as long as the humidity is appropriate. If the humidity rises again, the drying operation will also resume.In both programs, both the current humidity and the target humidity are displayed. Blower and fan stages:The blower is an electronically operated, energy-efficient radial fan. The stream of dry air blows slightly downward from the outlet, meaning that the air is directed into the lower area of the laundry, where the laundry is usually the most damp. This downward air channel is also very practical when placing a drying rack in front of the device.Selectable fan levels: The WT280 has one (powerful) fan level. This provides quick drying results, even with a lot of laundry and long drying rooms of up to about 10m.Adjustable air louvers:Flexible slats are installed at the air outlet, which can be adjusted laterally and in height, allowing the air to be more accurately adapted to the length/width of the clotheslines. Direct hose connection:The water extracted from the laundry runs into a hose, which is installed slightly below the middle of the back wall of the WT devices, instead of the usual position at the bottom of the device. This is advantageous compared to other models when the slope to the drain is not very steep or when the device is to be hung slightly lower. The device does not have a built-in pump, so the hose must have a continuous slope to the drain. If no drain is available, the water can of course also be easily collected in a bucket placed under the device. We offer suitable inlet pipes and buckets in our range if needed.Air filter:The humid room air is drawn in at the upper part of the front. A magnetically adhering filter with a frame cleans the air of coarse dust and lint, keeping the inside of the device clean. The filter consists of a very fine, closely woven nylon mesh. This has a high cleaning power, is easy to clean, and typically lasts for the entire lifespan of the dryer with proper care. Memory function:The settings are stored in the room monitoring program. In the event of a power interruption, the WT resumes operation with unchanged settings. It is therefore also suitable for operation with a timer, for example, when you only want to run the dryer during off-peak hours. If the power is interrupted during the laundry drying program, the device goes into standby and must be restarted. Room temperature:Technically, the WT dryers from Aerial can be used down to 8°C. Please note that the drying time for all room air dryers is significantly extended the colder the room is. For optimal drying speed, temperatures of 15°C and above are ideal. The declared drying performance was measured at a room temperature of 20°C. Made in Europe:The WT dryers are manufactured by the Dantherm Group in Europe. They have received very good ratings from the Swiss testing authority for tumble dryers "Swiss Testing." Service-friendly device construction:With just a few simple steps, the entire cover can be removed from the device. This makes handling easier in case of cleaning needs or service work, as the device does not need to be taken off the wall.    mounting on the wallThe installation is as simple as with all tumble dryers: a mounting rail is anchored to the wall with 2 screws, and the device can then be hung on it. All necessary mounting materials such as screws / dowels and a 2m hose are included in the delivery. Both the support rail and the two buffers supporting the device against the wall at the bottom are rubber insulated to minimize the transmission of vibrations to the wall. Due to the high dehumidification performance, we recommend draining the condensate directly into the drain with the hose (hose is included in the delivery). If you wish to use a bucket, please ensure that it has sufficient capacity (min. 8 liters) to avoid overflow during drying. If wall mounting is not possible, you will find suitable trolleys in our range to which the dryer can be mounted. "Upon request, we will professionally install the dryer at your home within a radius of up to 120 km for Fr. 210.-. For further distances, price upon request."Calculate distanceImportant:• Sanitary (drainage) or electrical (230V socket) installations are not carried out by us and must be commissioned separately by you through an appropriate craftsman, unless already in place.• If your wall has internal insulation, we need to know this when placing the order, as the installation will be more complex. The stated installation prices refer to direct wall installation, meaning directly on brick or concrete walls without insulation. Additional costs for installation on insulated walls will be charged based on effort.  Technical data drying room: up to 40 m² Drying performance: 3.68 Kg/h Consumption per kg of laundry:   0.29 kWh Energy efficiency: A1 Tension: 230V / 50Hz Power consumption: max. 1350W or 950W (at 20°C/60% r.H.) Sound pressure level: (our measurement) 2.5 m distance 67 dB(A)   Examples of dehumidification performance and consumption: at 30°C / 80% r.H = 79.2 L/24h (Power consumption: 1390 W) at 27°C / 60% r.H. = 46.6 L/24h (Power consumption: 1080 W) at 20°C / 60% r.H. = 32.2 L/24h (power consumption: 990 W) at 10°C / 70% r.H. = 20.3 L/24h (Power consumption: 800 W) air circulation volume: 950 m³/h condensate tank: No integrated tank. With hose connection, the water directly drained into the drain or into a bucket. Compressor: Rotary compressor refrigerant: R407C Dimensions (H/W/D): 80.9 x 64.0 x 34.5 cm Weight: 43 Kg Business closure: Digital Ambient temperature: 8°C ~ 32°C Swiss plug: Yes hose connection: Yes Guarantee: 3 years

Learn more More Fewer