A good, affordable racing horse for builders and water damage restorers. This dehumidifier has consistently omitted everything that is unnecessary for continuous operation. It has neither a display nor a hygrostat (a plug-in hygrostat can be optionally ordered if needed). This makes it very easy to operate, safe from tampering, and exceptionally low in price. On the other hand, it has everything needed for effective and quick drying: powerful dehumidification performance, hot gas defrosting, hour counter, as well as large wheels and a handle for easy mobility on construction and damage sites.     Easy handling   "The commissioning is child's play. Plug in - flip the main switch - done!"   The operation continues until either the bucket is full or the dryer is uninstalled again. As long as the device is connected to the power supply, it runs reliably and there are no settings that can be accidentally changed or manipulated. This also applies in the event of a power outage: when the power returns, the dehumidifier resumes its task with unchanged settings.   Thanks to the professional hot gas automatic control, operation in cooler environments is also possible without any issues, although the dehumidifying power, as with all condensation dryers, decreases at low temperatures. The installed finned evaporator (cooling element) has an exceptionally high efficiency in tempered environments and can dry the air to just below 40% relative humidity. Furthermore, the dryer is equipped with a rolling piston compressor. This means that it can be transported and stored in any position.     Optional Hygrostat   "Should a hygrometer for regulating the target humidity be required at any point, the dryer is prepared so that the Trotec Hygrostat HG110 can be connected directly via a jack plug. Please note the accessories."     Bucket and direct hose connection   The water extracted from the air is collected in a bucket with a capacity of 5 liters. A magnetic float automatically interrupts operation when full, and a warning light visually indicates that the bucket should be emptied. A hose can be connected to the bucket if needed, in case the water can be drained directly. The hose must be laid downwards, as no pump is integrated in the dryer.     Suitable for unattended continuous operation   This "TTK" is suitable for longer, unattended drying operations. The exact operating time can be precisely determined with the standard integrated hour meter. This is particularly useful for commercial applications. Thanks to the meter, it can also be tracked whether the device was always in operation or if it was accidentally or intentionally turned off.     Propane (R290) as an environmentally friendly refrigerant in dehumidifiers   "Every year, several million tons of environmentally harmful CO2 emissions (greenhouse gases) are released into the air due to synthetic refrigerants. Therefore, the use of alternative refrigerants is one of our most important goals. By using propane (R290) as a refrigerant, this dehumidifier makes a valuable contribution to climate protection."   The natural refrigerant propane (R290) is an organic compound and belongs to the hydrocarbons. Unlike synthetic refrigerants, environmentally friendly propane (R290) has neither ozone depletion potential (ODP=0) nor a significant greenhouse effect (GWP=3).   Supplement plus for the environment: Due to its excellent thermodynamic properties, propane (R290) is a particularly energy-efficient refrigerant, thereby additionally reducing your energy costs.     Advantages at a Glance   • Affordable price with strong performance in the commercial sector• Thanks to hot gas defrosting, it can also be used in cooler environments.• Robust steel construction with large wheels and guide bracket• Suitable for continuous operation• Thanks to the roll piston compressor, it is transportable and storable in any position.• External hygrometer connection     Technical data  dehumidification performance at 30 °C / 80 % r.H. 50 liters / day air volume 350 m³/ h Maximum room size 125 m² (310 m³) Minimum room size 8 m² (30 m³) temperature range 5 - 32°C Moisture range technical Moisture Range Practice 35 - 90 % r.F. 40 - 90 % r.H. (lamella evaporator) Voltage 220 - 240 V/50 Hz rated current consumption max. 3.7 A Power consumption max. 820W Recommended Coverage 10 A Cable length approx. 2 m Plug EU plug with Swiss adapter refrigerant R290 (230g) GWP3 water bucket 5 Liter operating noise 56 dB(A) at 1 m distance 53 dB(A) at a distance of 2.5 m Dimensions L x W x H 495 x 455 x 900 mm Weight 31 kg defrosting automatic Heissgas dehumidification automation Continuous operation, an insertable mechanical hygrometer is optionally available. Ventilator axial, single-stage blower automatic shut-off when bucket is full and prefilter and operating hour meter and Continuous operation possible and Display no memory function yes (automatically saves set values) hose connection yes, not included in the delivery (suitable inner diameter: 12 mm) guarantee 2 years Documents / Downloads   User Manual German   User manual French   User manual Italian   User manual English

Learn more More Fewer

Semi-professional dehumidifier for basements, construction sites, and laundry drying   This comfort dehumidifier protects and preserves what is dear and valuable to you. It is suitable for both robust dehumidification tasks in basements and laundry rooms, as well as for professional use in drying water damage or for keeping construction sites dry. Thanks to hot gas defrosting, it is also recommended for optimal drying results at low temperatures.     The all-rounder: Protects against mold, corrosion, and construction damage Excess moisture in the indoor air (> 60 percent) provides an ideal environment for pathogens. Mold also spreads in living spaces starting from this value, increasing the risk of respiratory diseases. Classic cars in the garage, artworks on the walls, and archived documents and books also suffer from excessive humidity. The causes of harmful humidity are diverse: deficiencies in building sealing, insufficient ventilation, as well as storms, flooding, or leaks in water-carrying pipes. The 122E keeps it dry.     Compact design – outstanding dehumidification performance Whether as a room climate improver in private settings or as a dehumidifier in commercial use – the cuboid stainless steel dehumidifier impresses with its comfortable features (e.g. 24h timer and auto-restart function as well as control panel lock function), an 8-liter condensate tank, and a strong dehumidification performance of 38 l/24 h at an air volume of 240 m³/h – sufficient for room sizes up to 100 m² or 250 m³. Thanks to the auto-restart function (memory function), the device automatically starts again in the pre-selected settings after a brief power interruption. For maximum user comfort, the control panel is equipped with easy-care membrane buttons and a digital display of room temperature and humidity. The target humidity can be set in 5 percent increments. Standard features also include a fill level warning light for a full water tank, overflow protection with automatic shut-off, and a reusable air filter that is easy to clean.     Gentle laundry drying with dehumidifiers In addition to dehumidifying the room air, a dehumidifier can be comfortably used for drying laundry – either as a support or as a complete replacement for a conventional tumble dryer. The laundry drying function (or textile drying mode or SuperDry function) is comparable to traditional air drying outdoors. Dehumidifiers offer the advantage that laundry is dried gently, just like in nature. Colors remain vibrant, and clothing has a longer lifespan than with conventional tumble dryers, all while consuming significantly less electricity."In addition, sensitive materials such as wool, silk, or synthetic fibers can also be dried without concern. In contrast to pure air drying, the laundry becomes much softer and more pleasant to wear on the skin."    Environmentally friendly refrigerant R290 Annually, several million tons of environmentally harmful CO2 emissions (greenhouse gases) are released into the air due to synthetic refrigerants. Therefore, the use of alternative refrigerants is one of our most important goals. By using propane (R290) as a refrigerant, this air dehumidifier makes a valuable contribution to climate protection. The natural refrigerant propane (R290) is an organic compound and belongs to the hydrocarbons. Unlike synthetic refrigerants, environmentally friendly propane (R290) has neither ozone depletion potential (ODP=0) nor a significant greenhouse effect (GWP=3).   Additional plus for the environment: Due to its excellent thermodynamic properties, propane (R290) is a particularly energy-efficient refrigerant, thereby further reducing your energy costs.     A dehumidifier for all occasions • Optimal suited for a healthy indoor climate in living areas• Moisture protection in archives, libraries, and art exhibitions• Corrosion and mold protection in (classic car) garages, basements, and storage rooms• Construction site drying and drying of damp masonry after water damage     Connection for external condensate drainage "For applications where regular emptying of the 8-liter condensate container is either not possible or undesirable, such as during unattended continuous drying operations in the basement, garage, holiday home, or on boats, the dryer features a built-in hose connection for direct drainage of the condensate into a drain. A short piece of suitable hose is already included in the delivery."     Hot gas defrosting automatic for faster drying results In low temperature ranges (below 12 °C), the integrated hot gas defrosting automatic system ensures consistently reliable air dehumidification – without long defrosting phases. Unlike the time-consuming recirculation defrosting of normal condensate dryers, the defrosting occurs through hot gas injection into the evaporator. This significantly shortens the duration of defrosting and achieves the drying goal more quickly.     SuperDry function for accelerated textile drying Practically for the quick dehumidification of wet laundry, clothing, or carpets is the special SuperDry function. This allows even large textiles to dry in no time, which do not fit in the tumble dryer.    Advantages at a Glance • Quality hot gas defrost automatic system• SuperDry function for accelerated textile drying• Automatic hygrostat-controlled dehumidification operation with real value humidity preset• Activated carbon filter against unpleasant odors• 24-hour timer• Auto-restart function (memory function) • suitable for construction drying • suitable for drying damp basements• suitable for laundry drying• Permanent mode• Easy-care material mix with a distinctive look• Digital display of current humidity and temperature values• Locking function of the control panel (child safety)     Technical data   dehumidification performanceat 30 °C / 80 % r.H. 38 liters / day air volume 240 m³/ h Maximum room size 100 m² (100 m³) Minimum room size 8 m² (20 m³) temperature range 5 - 35°C moisture range 30 - 90 % r.F. Voltage 220 - 240 V/50 Hz rated current consumption max. 2.9 A Power consumption max. 750W Recommended Coverage 10 A Cable length approx. 2 m Plug EU plug with Swiss adapter refrigerant R290 (96g) GWP3 water bucket 8 Liter operating noise 52 dB(A) at 1 m distance49 dB(A) at a distance of 2.5 m Dimensions L x W x H 453 x 310 x 635 mm Weight 27.5 kg defrosting automatic Heissgas dehumidification automation Hygrostatgesteuert Ventilator axial, 2-stage blower automatic shut-off when bucket is full and prefilter and Timer and Continuous operation possible and Laundry drying mode and Display shows current room humidity, set air humidity memory function yes (automatically saves set values) hose connection yes, short hose piece included in the delivery guarantee 2 years   Documents / Downloads   User Manual German   User manual French   User manual Italian   User manual English

Learn more More Fewer

A high-quality work and assembly tent with a thoughtful design. Ideal for use on construction sites and in roadworks in the trade. "Even with just one person, the tent can be set up effortlessly in seconds and can be easily carried to other locations thanks to its lightweight. The possible extensions and a whole range of accessories also allow for tasks from electrical installations to welding work. Furthermore, the lightfastness of the polyester fabric used and the enormous flexibility provided by lightweight and robust materials are impressive." The assembly tent not only provides protection from rain but also from cold. Clever rain protection strips on all zippers prevent water from entering. And even in darkness, the tent is well visible thanks to reflective strips.  Advantages at a Glance • 3 zippers in the front, so that the entrance can be rolled up completely or partially.• 2 closable vents with grille and rain protection cloth• Transport bag included in delivery• Dimensions L x W x H: 120 x 120 x 200 cm• Weight: approx. 10 kg "Available upon request also individually with your company logo and in your desired colors." Trotec Article No. 4.110.003.046

Learn more More Fewer

Perfect all-rounder for construction, trade, and water damage restoration   This Trotec dehumidifier impresses with powerful dehumidification performance combined with a strong fan that blows the dried air back into the room at high speed. This means that the room air is optimally circulated, and the drying process, especially in large, highly humid, or shelf-adjusted archive and storage rooms, is significantly faster.   The vehicle construction with guiding bow, carrying troughs, and large wheels facilitates transport even in difficult terrain sections or on stair steps.   For quick commissioning, the dryer features an easy-to-use control panel with a digital display of all functions. For hygrostat-controlled automatic operation, the target value can be pre-selected in percentage steps, which is then displayed together with the current actual value. The selectable target humidity range is from 20 - 90 %, although in practice, values below 35 % are difficult to achieve. This device operates at its full capacity in at least slightly heated rooms, with an ideal temperature of 12 °C or higher.   "With the timer, you can configure the on or off times, and thanks to the integrated memory function, the settings are retained even after a power interruption. This means that operation with a timer is also possible."     Bucket and direct hose connection The water extracted from the air is collected in a bucket with a capacity of 5.5 liters. A magnetic float automatically interrupts operation when full, and a warning light visually indicates that the bucket should be emptied. A hose can be connected to the bucket if needed, in case the water can be drained directly. The hose must be laid with a downward slope, as there is no pump integrated in the dryer (optionally, a standalone condensate pump is available from us if the water can or should be transported upwards or over a distance).     With optional air hose connection for cavity drying   "Whether in suspended ceilings, in bathtub cavities, in cassette walls, or cable ducts – when moisture has penetrated poorly accessible cavities, quick action should be taken to prevent mold formation. This dehumidifier is also suitable for this purpose, as it is equipped with a specially powerful fan with 3.2 MPa air pressure. An air hose with a suitable adapter can be optionally attached to it, allowing the dry air to be directed precisely to the damp areas."   Note: If there is heavy dirt, dust, or already mold in the cavity, the room should ideally not be occupied or used during this drying process, as otherwise, dust particles and mold spores can spread everywhere. In this case, the additional use of an air purifier is recommended.      Propane (R290) as an environmentally friendly refrigerant in dehumidifiers   "Every year, several million tons of environmentally harmful CO2 emissions (greenhouse gases) are released into the air due to synthetic refrigerants. Therefore, the use of alternative refrigerants is one of our most important goals. By using propane (R290) as a refrigerant, this dehumidifier makes a valuable contribution to climate protection."   The natural refrigerant propane (R290) is an organic compound and belongs to the hydrocarbons. Unlike synthetic refrigerants, environmentally friendly propane (R290) has neither ozone depletion potential (ODP=0) nor a significant greenhouse effect (GWP=3).   Supplement plus for the environment: Due to its excellent thermodynamic properties, propane (R290) is a particularly energy-efficient refrigerant, thereby additionally reducing your energy costs.     Advantages at a Glance   • Particularly economical solution for typical dehumidification applications in the commercial sector• High dehumidification performance even at low temperatures• Air hose connection for localized dry air application or cavity drying• Robust steel construction in vehicle design• Thanks to the roll piston compressor, it is transportable and storable in any position.• Timer Function• Memory function (auto-restart function)• Permanent mode for continuous operation• Maintenance-friendly magnetic closure door   Technical data   dehumidification performance at 30 °C / 80 % r.H. 51 liters / day air volume 450 m³/ h Maximum room size 130 m² (330 m³) Minimum room size 12 m² (30 m³) temperature range 5 - 30°C Moisture range technical Moisture Range Practice 20 - 90 % r.F. 35 - 90 % r.H. (lamella evaporator) Voltage 220 - 240 V/50 Hz rated current consumption max. 2.7 A Power consumption max. 650W Recommended Coverage 10 A Cable length approx. 2 m Plug EU plug with Swiss adapter refrigerant R290 (230g) GWP3 water bucket 5.5 Liter operating noise 52 dB(A) at 1 m distance 49 dB(A) at a distance of 2.5 m Dimensions L x W x H 525 x 490 x 900 mm Weight 40 kg defrosting automatic Recirculation, electronic dehumidification automation Hygrostatgesteuert Ventilator radial, single-stage blower automatic shut-off when bucket is full and prefilter and Timer and Continuous operation possible and Display shows current room humidity, set air humidity memory function yes (automatically saves set values) hose connection yes, no hose included in the delivery guarantee 2 years

Learn more More Fewer

This powerful axial fan, combined with thoughtful accessories, offers a versatile solution for numerous applications. It is ideally suited for ventilation, air circulation, and dust extraction, for both cold and warm air. For transport over longer distances, various air transport hoses are available, while dust bags effectively capture dirt in enclosed spaces. Thanks to the variable accessory modules, you only need this one fan to perform a variety of tasks that you would have previously needed multiple devices for. This high-performance fan, like all models in the TTV series, has been specifically designed for use in the toughest conditions. Its robust construction and high reliability ensure a long service life, even in material-intensive continuous operation at varying locations. The powerful blower enables strong and large-volume air circulation, which leads to accelerated evaporation. The higher the flow velocity at the material surface, the faster the drying process occurs. By combining the dryer and blower, the drying time can be reduced by up to 50%, depending on the design. A versatile adapter for numerous applications: The hose adapter can be attached to the fan on both sides to optionally realize suction or ventilation. Additionally, by using two hose adapters, the combined use of air transport hose and dust bag for effective suction of dirt particles is possible.   Protection from dust during renovation work   During renovation work, material processing, and disposal, a lot of dust is inevitably generated. Therefore, protect yourself and your employees from hazardous fine dust while working. A proven alternative to reduce dust exposure is the extraction of dirt and dust particles. The washable Trotec dust bags have a permeability of max.     Advantages at a Glance   • Extremely robust for professional continuous use even under the harshest conditions• Spray water protected (IP55)• Space-saving stackable for transport and storage• Suitable hose adapter available: The optional attachment allows for the connection of air transport hose or dust bag, e.g. for the extraction of dirt particles.     Technical data   Air volume max. 5300 m³ / Std. (free blowing) Ventilator Axial Fan speeds 3 Air speed 11 m/s (= 39.6 km/h) Throwing distance outside 15 mwithin 50 m Air pressure 80 Pa (at highest level) Funding temperature max. 45 °C Mains connection 230 V, 50 Hz Nominal current consumption 1.1 A Power consumption 250 W Insurance 10 A Cable + plug 3m, EU plug with Swiss fixed adapter Protection class IP55 Operating noise 53 dB(A) at a distance of 3m hose connection Diameter 450 mm Dimensions H x W x D 520 x 515 x 358 mm Weight 14.5 kg Trotec article no. 1.510.000.010 Guarantee 2 years  

Learn more More Fewer

The universal all-rounder   "Whether for drying out after water damage, new building drying, or maintaining dry conditions in heated and unheated storage rooms - the 170S is a universally applicable dehumidifier with high-quality workmanship and reliable operation. It is manufactured in a specialized plant in Europe. It is built to last, easy to maintain, rarely needs servicing, and is very affordable considering its power and quality.".     Easy handling   "Using a mechanical hygrometer, the desired target humidity can be continuously adjusted between 32 - 100%, and continuous operation is also possible. Particularly useful in larger areas is the high air circulation volume of a substantial 580 cubic meters per hour. With its stable cart construction and large wheels, frequent relocation to different usage sites can be easily carried out."     Bucket, direct hose connection and optional pump kit   The water, which is extracted from the air, flows into the 6-liter bucket. This is placed on a scale that automatically interrupts operation when full. A control light indicates the full status in this case. Furthermore, there is the possibility to connect a hose if the water can be drained directly. The hose must have a slope towards the drain in this case. If this is not possible, a suitable pump kit is optionally available, with which the water can be pumped upwards and also outwards.   "The operating switch and level warning light are protected against dust and splashing water by a protective cover, and a slotted hygrostat rotary switch prevents unwanted adjustment of the switch position."     Professional Hot Gas Defrosting   Inside, a professional hot gas defrosting automatic system ensures effective dehumidification results. The fin evaporators unleash their power particularly in temperature ranges above 10°C and in areas above 40% humidity. Technically, the dryer can also be used in lower ranges down to about 5°C, even in unattended continuous operation.     Optional counters   The delivery includes no "Hour or consumption meters are included. You can order them from us upon request (the housing is standardly prepared for retrofitting). You have the choice between a pure hour meter or the combined dual meter, which measures hours and electricity consumption. The meters are MID compliant. Outside of Switzerland, dryers in professional use must already be MID compliant."     Propane (R290) as an environmentally friendly refrigerant in dehumidifiers   Annually, several million tons of environmentally harmful CO2 emissions (greenhouse gases) are released into the air due to synthetic refrigerants. Therefore, the use of alternative refrigerants is one of our most important goals. By using propane (R290) as a refrigerant, this dehumidifier makes a valuable contribution to climate protection. The natural refrigerant propane (R290) is an organic compound and belongs to the hydrocarbons. Unlike synthetic refrigerants, environmentally friendly propane (R290) has neither ozone depletion potential (ODP=0) nor a significant greenhouse effect (GWP=3).   Supplement Plus for the Environment: Due to its excellent thermodynamic properties, propane (R290) is a particularly energy-efficient refrigerant, thereby additionally reducing your energy costs.     Advantages at a Glance   • High dehumidification performance even at low temperatures• Robust plastic-coated metal housing• Thanks to the roll piston compressor, it is transportable and storable in any position.• Stable carriage construction• Automatic hygrostat-controlled dehumidification operation• Quality hot gas defrost automatic system• Option to retrofit MID-compliant dual meter for operating and kilowatt hours (optional) • Option to add a suitable pump kit that can be connected directly to the device (optional)   Technical data  dehumidification performance at 30 °C / 80 % r.H. 40 liters / day air volume 580 m³/ h Maximum room size 100 m² (250 m³) Minimum room size 8 m² (20 m³) temperature range 5 - 32°C Moisture range technical Moisture Range Practice 32 - 90 % r.F. 40 - 90 % r.F. Voltage 220 - 240 V/50 Hz rated current consumption max. 2.8 A Power consumption max. 600W Recommended Coverage 10 A Cable length approx. 3 m Plug EU plug with Swiss adapter refrigerant R290 (150g) GWP3 water bucket 6 Liter operating noise 52 dB(A) at 1 m distance 49 dB(A) at a distance of 2.5 m Dimensions L x W x H 540 x 490 x 963 mm (incl. guide bracket) Weight 32 kg defrosting automatic Heissgas dehumidification automation Hygrostatgesteuert Ventilator axial, single-stage blower automatic shut-off when bucket is full and prefilter and Timer no (operation on timer possible) Continuous operation possible and memory function yes (mechanically stores set values) hose connection yes (no hose included in the delivery) - 12 mm Pump optional available (not included in the scope of delivery) guarantee 2 years

Learn more More Fewer

In civil engineering, the work tent protects against rain and cold in bad weather. Simply placed over a construction pit, it offers no cracks or holes for water to penetrate due to its special processing.   "Even during welding work, the tent reliably shields the area of activity. A particular advantage when working on electrical installations is the lightfastness provided by the fabric of the tent."     Advantages at a Glance   • 3 zippers in the front, so that the entrance can be rolled up completely or partially.• 2 lockable vents with grille and rain protection cloth• thought-out system with fiberglass poles• easy to clean polyester cloth• Assembly in seconds with just one person• incredibly versatile• Transport bag is included• Plastic tent pegs for better grip• maintenance-free and durable• low weight of approx. 23 kg• Dimensions of L 210 x W 210 x H 200 cm   "Available upon request also individually with your company logo and in your desired colors."   Trotec Article No. 4.110.003.065

Learn more More Fewer

Professional construction dehumidifier with large bucket A high-quality dehumidifier for commercial use and water damage drying, manufactured in Europe. Its impressive exterior appearance is matched by its internal values: all electrical components are specially encapsulated, protecting the electronics from harmful deposits that could impair their function and longevity. Therefore, this dryer is also ideally suited for use under demanding conditions. Thanks to its maintenance-friendly design, it is easy to care for. "Compared to more affordable piston compressors, the high-quality 0.58 kW rotary compressor installed here offers the advantage of higher performance with comparatively lower power consumption – and additionally provides reserves for high dehumidification performance even in unheated rooms."In addition, the high-quality hot gas defrosting automatic system ensures a much more efficient dehumidification performance compared to other defrosting devices, without time interval-related defrosting pauses during which no dehumidification takes place.  Propane (R290) as an environmentally friendly refrigerant in dehumidifiers Annually, several million tons of environmentally harmful CO2 emissions (greenhouse gases) are released into the air due to synthetic refrigerants. Therefore, the use of alternative refrigerants is one of our most important goals. By using propane (R290) as a refrigerant, this air dehumidifier makes a valuable contribution to climate protection. The natural refrigerant propane (R290) is an organic compound and belongs to the hydrocarbons. Unlike synthetic refrigerants, environmentally friendly propane (R290) has neither ozone depletion potential (ODP=0) nor a significant greenhouse effect (GWP=3).  Supplement plus for the environment: Due to its excellent thermodynamic properties, propane (R290) is a particularly energy-efficient refrigerant, thereby additionally reducing your energy costs.  User-friendly Thanks to its durable housing, ergonomic grip recesses with an internal grip clip, and four sturdy wheels with a roll stop, the device is ideally suited for use on construction sites and for drying water damage. However, these advantages are also appreciated in commercial spaces or in private basement environments. The storage is also well thought out: two practical stacking grooves on the top of the device allow for a stable and space-saving stacking during transport and in storage.   An integrated operating hour meter reliably documents the exact duration of use even during longer drying operations.   Integrated compressor thermal protection with automatic shut-off   In drying operations with extremely high humidity and simultaneously high temperatures – for example, during water damage restoration – refrigerant dryers quickly enter their red performance zone. Here, the catchy "35 rule" applies: water damage above 35 degrees reduces the dryer’s lifespan to below 35%. However, this is not a question of component quality, but pure physics, which applies independently of the manufacturer to all refrigerant dryers on the market.  While most professional condensate dryers can still operate without issues at moderate humidity around 70% r.F. up to 35 °C, very high humidity combined with high room temperature results in significantly more energy being supplied to the humid air, which must be additionally "processed" through the refrigerant. Consequently, the pressure of the refrigerant in the system increases immensely, leading to a destructive load on the compressor. Although the dehumidifiers will initially continue to operate, they will do so well beyond their limit "deep in the dark red zone," resulting in an extremely shortened remaining lifespan.  "Therefore, the commercial dehumidifiers of the TTK-S series are equipped with an integrated compressor thermal protection for the active preservation of your devices:"Sensors continuously monitor the thermal load of the compressor. If the temperature is within the defined operating range, the integrated heat protection indicator pulses in a long sequence, indicating optimal operation of the dehumidifier. As soon as the temperature exceeds the critical threshold of 35 °C, the automatic system switches off the compressor to protect it, while the fan continues to operate, and automatically reactivates the compressor as soon as the 35° threshold is fallen below again. This protection not only significantly extends the lifespan of the dehumidifiers, but also prevents thermal damage to materials in the room and the building structure during their use.   Options • Dual meter available for additional recording of electricity consumption.• high-performance condensate pump for permanent drying with a pumping capacity of up to 50 m distance and a maximum delivery height of 4 m  Advantages at a Glance • High dehumidification performance even at low temperatures • Maximum dust and moisture protection for all electrical components• Extremely maintenance-friendly design • Optimal handling characteristics • Thanks to the roll piston compressor, it is transportable and storable in any position. • Practical stacking groove for stable, space-saving storage and transport • Multistage capability with identical models• Practice-oriented industrial design• Made in Europe  Technical data  dehumidification performance at 30 °C / 80 % r.H. 28 liters / day air volume 250 m³/ h Maximum room size 70 m² (175 m³) Minimum room size 8 m² (30 m³) temperature range 5 - 32°C moisture range 35 - 90 % r.F. Voltage 220 - 240 V/50 Hz rated current consumption max. 2.3 A Power consumption max. 500W Recommended Coverage 10 A Cable length approx. 3 m Plug EU plug with Swiss adapter refrigerant R290 (150g) GWP3 water bucket 6 Liter operating noise 52 dB(A) at 1 m distance 49 dB(A) at a distance of 2.5 m Dimensions L x W x H 375 x 345 x 603 mm Weight 26 kg defrosting automatic Heissgas dehumidification automation Hygrostatgesteuert Ventilator axial, single-stage blower automatic shut-off when bucket is full and prefilter and Timer no Continuous operation possible and memory function yes (mechanically stores set values) hose connection yes, short hose piece included in the delivery guarantee 2 years   

Learn more More Fewer

The robust and powerful all-rounder   "Whether for drying out after water damage, new building drying, or maintaining dry conditions in heated and unheated storage rooms - the 350S is a universally applicable dehumidifier with high-quality workmanship and reliable operation. It is manufactured in a specialized plant in Europe. It is built to last, easy to maintain, rarely requires servicing, and is very affordable considering its power and quality."  Easy handling The desired target humidity can be continuously regulated between 32 - 100% using a mechanical hygrostat, and continuous operation is also possible. With the used lamella evaporator, target humidities below 40% r.H. are difficult to achieve; however, this technology shows impressive dehumidification power in temperate and humid environments. Particularly useful in larger areas is the high air circulation volume of a substantial 1000 cubic meters per hour. With its stable trolley construction and large wheels, frequent relocation to different sites can be easily carried out.  Bucket, direct hose connection and optional pump kit The water, which is extracted from the air, flows into the 6-liter bucket. This is placed on a scale that automatically interrupts operation when full. A control light indicates the full status in this case. Furthermore, there is the possibility to connect a hose if the water can be drained directly. The hose must have a slope towards the drain in this case. If this is not possible, a suitable pump kit is optionally available, with which the water can be pumped upwards and also outwards. "The operating switch and level warning light are protected against dust and splashing water by a protective cover, and a slotted hygrostat rotary switch prevents unwanted adjustment of the switch position."     For continuous operation on construction sites   The possibility of connecting an external condensate drain – optionally with a condensate pump if needed – makes the construction dryer also ideally suited for longer unattended drying tasks, e.g. in construction drying.     Optional counters The delivery does not include an hour or consumption meter. You can order these from us if desired (the housing is standardly prepared for retrofitting). You have the choice between a pure hour meter or the combined dual meter, which measures hours and power consumption. The meters are MID compliant. Outside of Switzerland, dryers in professional use must already be MID compliant.     Hydrofluorolefin (R-454C) as an environmentally friendly refrigerant in dehumidifiers   "Every year, several million tons of environmentally harmful CO2 emissions (greenhouse gases) are released into the air due to synthetic refrigerants. Therefore, the use of alternative refrigerants is one of our most important goals. By using hydrofluoroolefin (R-454C) as a refrigerant, this dehumidifier makes a valuable contribution to climate protection."   The natural refrigerant hydrofluoroolefin (R-454C) is an organic compound and belongs to the hydrocarbons. Unlike synthetic refrigerants, the environmentally friendly hydrofluoroolefin (R-454C) has neither ozone depletion potential (ODP=0) nor a significant greenhouse effect (GWP=146).   Supplement Plus for the Environment: Due to its excellent thermodynamic properties, hydrofluoroolefin (R-454C) is a particularly energy-efficient refrigerant, thereby additionally reducing your energy costs.     Advantages at a Glance • High dehumidification performance even at low temperatures• Robust plastic-coated metal housing• Thanks to the roll piston compressor, it is transportable and storable in any position.• Stable carriage construction• Automatic hygrostat-controlled dehumidification operation• Quality hot gas defrost automatic system• Option to retrofit MID-compliant dual meter for operating and kilowatt hours (optional)• Option to add a suitable pump kit that can be connected directly to the device (optional)     Technical data   dehumidification performance at 30 °C / 80 % r.H. 55 liters / day air volume 1000 m³/ h Maximum room size 140 m² (350 m³) Minimum room size 8 m² (20 m³) temperature range 5 - 32°C Moisture range technical Moisture Range Practice 32 - 90 % r.F. 40 - 90 % r.F. Voltage 220 - 240 V/50 Hz rated current consumption max. 6.1 A Power consumption max. 1400W Recommended Coverage 10 A Cable length approx. 3 m Plug EU plug with Swiss adapter refrigerant R454C (650g) GWP146 water bucket 6 Liter operating noise 54 dB(A) at 1 m distance 51 dB(A) at a distance of 2.5 m Dimensions L x W x H 530 x 500 x 965 mm (incl. guide bracket) Weight 39 kg defrosting automatic Heissgas dehumidification automation Hygrostatgesteuert Ventilator axial, single-stage blower automatic shut-off when bucket is full and prefilter and Timer no (operation on timer possible) Continuous operation possible and memory function yes (mechanically stores set values) hose connection yes (no hose included in the delivery) Pump optional available (not included in the scope of delivery) guarantee 2 years

Learn more More Fewer

The DH25 is a powerful dehumidifier that is ideal for medium-sized rooms and environments with high humidity levels. It impresses with its reliable dehumidification performance in both cool and temperate spaces. As an evolution of the FDK44 model, it offers digital control and a slightly increased dehumidification capacity.OperationOperation is incredibly simple: The desired target humidity is set on the control panel. If the measured humidity exceeds the set value, the dehumidifier automatically starts operating; otherwise, it pauses. The display always shows the current room humidity. The DH25 unleashes its full dehumidification power especially for year-round drying of single or double garages, archives, basements, or for stabilizing humidity in laundry and drying rooms. Thanks to its highly advanced hot gas defrosting, the DH25 can be used down to just above freezing point. Its efficient dehumidification performance in low humidity ranges, where other dehumidifiers can no longer extract moisture from the air, is particularly noteworthy. The room air is drawn in from one side of the housing and cleaned through an industrial, reusable filter. The dried air is blown into the room from the opposite side, creating effective air circulation. The setup of the DH25 is flexible: it can be placed both on the floor and on a free shelf, with the wheels being lockable for a secure stand. The condensate is drained directly via a hose connection. It is important that the hose has a constant slope towards the drain to ensure smooth drainage. The DH25 is characterized by its solid and high-quality construction. The housing is made of white powder-coated metal, while the internal components meet professional standards. This allows for uninterrupted continuous operation without supervision. Even after a power failure, the dehumidifier resumes operation with the previous settings, making it ideal for use with timers or smart home systems. For easy mobility, the DH25 is equipped with four sturdy wheels (with brakes) and two foldable carrying handles. Versatile application• as a dehumidifier for warehouses, commercial and industrial spaces, garages, and basements• for continuous dehumidification of tempered but also cold rooms from 1°C• for unattended continuous operation• for operation on a timer     dehumidification performanceThe dryer can be used thanks to advanced hot gas defrosting over a wide temperature range from +1°C to +35°C, although, as with all condensation dryers, the dehumidifying power decreases in cooler environments. Examples of dehumidification performance under different (constant) ambient conditions:30°C/80% r.H.: 40 liters20°C/80% r.H.: 16 Liters20°C/60% r.H.: 12 Liters10°C/60% r.H.: 7 Liters(r.H.=relative humidity)   Optional accessoriesThe delivery includes the ready-to-plug-in device. If needed, we offer various suitable accessories, such as:• Hose coupling• Hose• Condensate pump (if the condensate needs to be pumped away to a higher location)Stronger designThe device is also available in double strength as "FDK100" -> DetailsComparable devices: Lunor L25     Technical data  Model: Trotec DH25S Tension: 230V / 50Hz Power consumption:  max. 700W / 510W (at 20°C/60% r.H.) Sound pressure level: (our measurement) 1 m distance 53 dB(A)2.5 m distance 51 dB(A) Dehumidification capacity: 40 liters/day (30°C / 80% r.H.)  Air circulation volume: 450 m³/h (installed, free-blowing approx. 650 m³) Condensation tank: No tank / only hose connection possible Compressor:     Rotary compressor  Refrigerant:   R290 (152gr.) Dimensions (L/H/D):      580 x 455 x 350 mm (including wheels and carrying handles) Weight:    30 Kg Business closure: Digital Ambient temperature: 1°C ~ 35°C  Area of application: up to 100m² Swiss plug:  EU plug with Swiss fixed adapter, 5m cable Hose connection:  Yes Guarantee: 2 years

Learn more More Fewer

This separator belongs to the family of the Trotec drying system "Multiqube". It can be integrated into this system, but can also be freely combined with any existing devices from other manufacturers via hose connections. Compared to other brands, the price-performance ratio of this model is excellent.     microfilter system   "It features an integrated microfilter system with a maintenance-friendly magnetic closure filter compartment. This makes it a flexibly deployable integral solution with all pre-HEPA filter stages in just one device."   Advantage: improved flow-optimized filter technology, faster assembly, less material - and space requirement - no separate additional microfilter housings necessary.     Use in combination with a compressor   The connected compressor's automatic shut-off and restart system provides optimal overflow protection that does not require monitoring. With the drying of the insulation layer, the processing of areas up to 40 m² is easily possible.     Extended application possibilities   The "TTKwic" quick couplings attached to the device allow for the connection of up to two dehumidifiers with a condensate pump, which pump the extracted water into the separator. This results in a central water discharge (hose connection Ø 12mm).     Advantages at a Glance   • Approx. 25% performance-enhanced filter technology thanks to filter compartment with microfilter cassette• Stainless steel element for water separation and fine filtration• Residual water drainage function• Active overflow protection through automatic switching on and off of the connected insulation layer dryer• Integrated connection cable• Cable collector• Extremely lightweight, robust, and particularly maintenance-friendly construction• Transport wheels with locking brakes• Maintenance quick-release fasteners• Emergency stop switch• Overflow sensor with automatic shut-off• Space-saving stackable• Lightweight material base: impact-resistant and robust construction, 100% recyclable • Two integrated TTKwic quick couplings for central water drainage for up to two connected dehumidifiers• Easy handling - easy to clean   scope of delivery   MultiQube, a microfilter cassette     Technical data  Volume 17 Liter power connection 230 V / 50 Hz Plug EU plug with Swiss fixed adapter Power consumption 320 W Number of air connections 3 suitable hose diameter 38 mm fine filter 3 pieces class F8 Weight 11.3 kg Masse (B x H x T) 440 x 395 x 420 mm Trotec article no. 6.100.000.006 guarantee 2 years

Learn more More Fewer

For professional use in industry, on construction sites, or during maintenance work.  The materials used are particularly robust yet surprisingly lightweight fabrics. The thoughtful tensioning system allows for a setup in seconds while still providing maximum stability and sturdiness. The lightfastness of the fabric is also an important factor for various tasks related to electrical installations.   The inconspicuous construction site tent proves itself time and again in everyday practice. Whether in rain or cold - it always offers you optimal protection and enough space for, for example, an electric heater.   Unlike the "250K" model, the "250KE" is equipped at the front with three zippers, allowing the entrance to be rolled up completely or partially. Two zippered ventilation openings with mesh and rain protection cloth are additional features. All zippers are protected from penetrating water by rain protection strips.   Advantages at a Glance • 3 zippers in the front, so that the entrance can be rolled up completely or partially.• 2 lockable vents with grille and rain protection cloth• thought-out system with fiberglass poles• easy to clean polyester cloth• Setup in seconds• incredibly versatile• Transport bag is included• Plastic tent pegs for better grip• maintenance-free and durable• low weight of approx. 25.8 kg• Dimensions of L 250 x W 250 x H 200 cm "Available upon request also individually with your company logo and in your desired colors." Trotec Article No. 4.110.003.075 

Learn more More Fewer

A very powerful construction dehumidifier with brutal dehumidification strength. Perfect for drying large construction sites and for the effective drying of water damage. This dehumidifier has consistently omitted everything that is unnecessary for continuous operation. It has neither a display nor a hygrostat (a plug-in hygrostat can be optionally ordered if needed). This makes it very easy to operate, safe from tampering, and exceptionally affordable in price for this performance class. On the other hand, it has everything needed for quick drying: strong dehumidification performance, hot gas defrosting, hour counter, as well as large wheels and a handle for easy mobility on construction and damage sites.     Easy handling   "The commissioning is child’s play. Set up - connect the hose - plug in - flip the main switch - done!"   The operation continues until the dryer is reinstalled. As long as the device is connected to the power grid, it runs reliably and there are no settings that can be accidentally changed or manipulated. This also applies in the event of a power outage: when the power returns, the dehumidifier resumes its task with unchanged settings.   Thanks to the professional hot gas automatic control, operation in cooler environments is also possible without any issues, although the dehumidifying power, as with all condensation dryers, decreases at low temperatures. The installed finned evaporator (cooling element) has an exceptionally high efficiency in temperate environments and can dry the air to just below 40% relative humidity. Furthermore, the dryer is equipped with a rolling piston compressor. This means that it can be transported and stored in any position.     Optional Hygrostat   "Should a hygrometer for regulating the target humidity be required at any point, the dryer is prepared so that the Trotec Hygrostat HG110 can be connected directly via a jack plug. Please note the accessories."     Direct hose connection   With dryers of this strength, collecting water in an integrated bucket makes little sense, as it would constantly fill up. The water extracted from the air is therefore drained through a directly connected hose. The hose must be laid with a downward slope, as there is no pump integrated into the dryer. Freestanding condensate pumps are optionally available if the water needs to be transported upwards or over a distance.     Suitable for unattended continuous operation   This "TTK" is suitable for longer, unattended drying operations. The exact operating time can be precisely determined with the standard integrated hour meter. This is particularly useful for commercial applications. Thanks to the meter, it can also be tracked whether the device was always in operation or if it was accidentally or intentionally turned off.     Hydrofluorolefin (R-454C) as an environmentally friendly refrigerant in dehumidifiers   "Every year, several million tons of environmentally harmful CO2 emissions (greenhouse gases) are released into the air due to synthetic refrigerants. Therefore, the use of alternative refrigerants is one of our most important goals. By using hydrofluoroolefin (R-454C) as a refrigerant, this dehumidifier makes a valuable contribution to climate protection."   The natural refrigerant hydrofluoroolefin (R-454C) is an organic compound and belongs to the hydrocarbons. Unlike synthetic refrigerants, the environmentally friendly hydrofluoroolefin (R-454C) has neither ozone depletion potential (ODP=0) nor a significant greenhouse effect (GWP=146).    Supplement plus for the environment: Due to its excellent thermodynamic properties, hydrofluoroolefin (R-454C) is a particularly energy-efficient refrigerant, thereby additionally reducing your energy costs.   Advantages at a Glance   • Affordable price with strong performance in the commercial sector• Thanks to hot gas defrosting, it can also be used in cooler environments.• Robust steel construction with large wheels and guiding handle• Suitable for continuous operation• Thanks to the roll piston compressor, it is transportable and storable in any position.• External hygrometer connection     Technical data  dehumidification performance at 30 °C / 80 % r.H. 100 liters / day air volume 1000 m³/ h Maximum room size 250 m² (750 m³) Minimum room size 8 m² (30 m³) temperature range 5 - 32°C Moisture range technical Moisture Range Practice 30 - 90 % r.F. 40 - 90 % r.H. (lamella evaporator) Voltage 220 - 240 V/50 Hz rated current consumption max. 8.1 A Power consumption max. 1920W Recommended Coverage 16 A Cable length approx. 2 m Plug EU plug with Swiss adapter refrigerant R454C (1000g) GWP146 water bucket no bucket operating noise 67 dB(A) at 1 m distance 64 dB(A) at a distance of 2.5 m Dimensions L x W x H 538 x 698 x 1006 mm incl. guide rail and rollers Weight 64 kg defrosting automatic Heissgas dehumidification automation Continuous operation, an insertable mechanical hygrometer is optionally available. Ventilator radial, single-stage blower prefilter and operating hour meter and Continuous operation possible and Display no memory function yes (automatically saves set values) hose connection yes, not included in the delivery (suitable inner diameter: 12mm) guarantee 2 years

Learn more More Fewer

The 650S is a robust and powerful construction dryer that stands out for its versatility. It effortlessly handles demanding tasks such as drying after water damage, new construction drying, and maintaining dryness in heated and unheated storage rooms. Manufactured in a specialized European facility, this dehumidifier impresses with its high-quality workmanship and reliable operation. The durable construction of the 650S guarantees a long lifespan, while the easy maintenance and low upkeep costs make operation even more economical. Despite its impressive performance and quality, the 650S is available at an extremely attractive price, making it an excellent choice for professional users.Easy to use The desired target humidity can be continuously regulated between 32 - 100 % using a mechanical hygrostat, and continuous operation is also possible. Particularly useful in larger areas is the high air circulation volume of a substantial 925 cubic meters per hour. With its stable cart construction and large wheels, frequent changes of location can be easily carried out.     Direct hose connection and optional pump kit   Due to its very high dehumidification performance, this dehumidifier has a direct connection for condensate drainage instead of a water tank. The hose must have a slope towards the drain. If this is not possible, a suitable pump kit is optionally available, which can pump the water upwards and also outwards.   The operating switch is protected against dust and splashes by a protective cover, and a slotted hygrostat rotary switch prevents unwanted adjustment of the switch position.     Professional Hot Gas Defrosting   Inside, a professional hot gas defrosting automatic system ensures effective dehumidification results. The fin evaporators unleash their power particularly in temperature ranges above 10°C and in the range above 40% humidity. Technically, the dryer can be used at room temperatures down to about 5°C, even in unattended continuous operation.     Optional counters   Included in delivery is no "Hour or consumption meters are included. You can order them from us upon request (the housing is standardly prepared for retrofitting). You have the choice between a pure hour meter or the combined dual meter, which measures hours and electricity consumption. The meters are MID compliant. Outside of Switzerland, dryers in professional use must already be MID compliant."     Hydrofluoroolefin (R-454C) as an environmentally friendly refrigerant   "Every year, several million tons of environmentally harmful CO2 emissions (greenhouse gases) are released into the air due to synthetic refrigerants. Therefore, the use of alternative refrigerants is one of our most important goals. By using hydrofluoroolefin (R-454C) as a refrigerant, this dehumidifier makes a valuable contribution to climate protection." The natural refrigerant hydrofluoroolefin (R-454C) is an organic compound and belongs to the hydrocarbons. Unlike synthetic refrigerants, the environmentally friendly hydrofluoroolefin (R-454C) has neither ozone depletion potential (ODP=0) nor a significant greenhouse effect (GWP=146).     Advantages at a Glance   • High dehumidification performance even at low temperatures• Robust plastic-coated metal housing• Thanks to the roll piston compressor, it is transportable and storable in any position.• Stable carriage construction• Automatic hygrostat-controlled dehumidification operation• Quality hot gas defrost automatic system• Option to retrofit MID-compliant dual meter for operating and kilowatt hours (optional) • Option to add a suitable pump kit that can be connected directly to the device (optional)     Technical data   dehumidification performanceat 30 °C / 80 % r.H. 91 liters / day Air volume 925 m³/ h Maximum room size 230 m² (550 m³) Minimum room size 4 m² Temperature range 5 - 32°C Moisture range technical Moisture Range Practice 32 - 90 % r.F. 40 - 90 % r.F. voltage 220 - 240 V/50 Hz Nominal current consumption max. 9.5 A Power consumption max. 2100 W Recommended Coverage 16 A Cable length approx. 3 m Plug EU plug with Swiss fixed adapter refrigerant R-454C (1050g) GWP 146 water bucket no bucket, only hose connection suitable hose: 16 mm inner diameter Operating noise 56 dB(A) at 1 m distance53 dB(A) at a distance of 2.5 m Dimensions L x W x H 616 x 511 x 1022 mm (incl. guide bracket) Weight 52 kg Automatic defrosting Heissgas dehumidification automation Hygrostatgesteuert Ventilator axial, single-stage blower Prefilter and Timer no (operation on timer possible) Continuous operation possible and Memory function yes (mechanically stores set values) hose connection yes (no hose included in the delivery) - 16 mm Pump optional available (not included in the delivery) Guarantee 2 years

Learn more More Fewer

A reliable wall-mounted dehumidifier with an appealing design. A durable, corrosion-protected construction made of powder-coated, galvanized steel sheet ensures maximum reliability for this industrial condensate dryer and makes it particularly resistant to environmental influences thanks to its protective-coated heat exchanger. The combination of high efficiency and low-maintenance design makes the dryer ideally suited for fully automatic, hygrostat-controlled continuous drying applications in numerous fields of use, and thanks to its autonomous recirculation operation, it can also be easily integrated into any application environment afterwards. With its KTL-coated heat exchanger, it is also extremely resistant to environmental influences even in particularly reactive air environments with high salt, chlorine, or solvent content.    Hygrostat controlled and protection against manipulation The built-in hygrostat automatically regulates the humidity to an optimal level, where condensation, mold, or corrosion have no chance. The target humidity can be freely adjusted according to your needs. High efficiency is ensured by the quiet-running AC axial fan and the powerful compression refrigeration system.  The dry air supplied to the room is simultaneously heated for process technology, so that the use of conventional heating and ventilation energy can be reduced.     Thanks to high-quality hot gas automation, the dryer requires only very short defrosting phases. This is optimal, especially for dehumidifying unheated rooms, as it improves the performance and increases efficiency.  The controls are protected against unauthorized access, making this industrial dryer also the ideal dehumidifier for public buildings, staff and changing rooms, or museums.    Wide range of applications In wall operation, the device can be used for a variety of applications, for example:  • Humidity control in staff rooms, changing rooms, lounges, and break rooms• Drying of changing rooms, gyms, bike and ski cellars• Constant humidity conditions in garages, workshops, test benches, or production halls• Dehumidification in archives, collections, or libraries• Dehumidification of water engineering facilities and pumping stations to prevent condensate formation on pipes or pumps• Humidity control during the storage of natural products, for example for quality assurance in wood storage or during the storage of raw tobacco.• Corrosion prevention in electrical switchgear, boiler systems, turbines, and piping systems in power plants or during the storage of raw bodies and metal components.• Humidity control in data centers, control rooms, etc.• Moisture control in the food industry, for example in cheese production or confectionery manufacturing Due to the horizontally directed recirculation airflow and its compact design, the plug-and-play dehumidifier is particularly well suited for installation above door areas.  The condensate drawn from the air is directly drained through a downward laid hose. If the water needs to be drained to higher areas, please also consider our pump kits.  Advantages at a Glance • Professional quality, made in Germany• High dehumidification performance even at low temperatures• Corrosion-protected construction• Fully automatic operation• Professional hot gas defrosting automatic system• Quiet AC axial fan for horizontal recirculation airflow• Optimal suited for installation above door areas• Control elements installed protected from unauthorized access• Available optionally with condensate pump  Technical data  dehumidification performance at 20 °C / 60 % r.H. at 30 °C / 80 % r.H.   11 liters / day 22 liters / day air volume max. 225 m³/ h Maximum room size 60 m² (150 m³) temperature range 5 - 40°C Moisture range technical  Moisture Range Practice 30 - 90 % r.F. 40 - 90 % r.H. (lamella evaporator) Voltage 220 - 240 V/50 Hz rated current consumption max. 3.7 A Power consumption max. 657W Recommended Coverage 10 A Plug approx. 3.5m connection cable with EU plug and Swiss fixed adapter refrigerant R-407C (480g) GWP1774 hose connection   Direct hose connection, no bucket suitable hose 10mm inner diameter short hose piece included in the delivery operating noise   53 dB(A) at 1 m distance 49 dB(A) at a distance of 3 m Masse (B x H x T) 840 x 330 x 365 mm Weight 37 kg defrosting automatic Heissgas dehumidification automation mechanical hygrostat wheel, stepless Ventilator axial, single-stage blower prefilter and operating hour meter no Continuous operation possible and Display no memory function yes (set values remain mechanically fixed) Trotec article no. 1.125.000.111 guarantee 2 years Documents / Downloads   User Manual German   User manual French   User manual Italian   User manual English

Learn more More Fewer

The three-stage adjustable turbo engine reaches up to 20000 rpm and guarantees maximum efficiency at every power level, as the current volumetric flow rate in m³ is continuously monitored thanks to the integrated automation, and the power is automatically adjusted to the optimal air throughput.   A single press of a button is enough, and the device switches either to a higher power class or, if needed, to the additionally available whisper mode:     Performance levels   Performance level 1: suitable for areas up to approx. 30 m² at overpressure / 25 m² at underpressure, motor power: 0.5 kWPerformance level 2: suitable for areas up to approx. 60 m² at overpressure / 50 m² at underpressure, motor power: 0.8 kW Performance level 3: suitable for areas up to approx. 90 m² at overpressure / 70 m² at underpressure, motor power: 1.2 kW   Comparison with predecessor models based on side channel blower technology: Performance level 1: Corresponds to the performance of a 0.8 kW side channel blowerPerformance level 2: approximately 10% stronger than a side channel blower with 1.1 to 1.3 kW powerPerformance level 3: Corresponds to 140% of the performance of a 1.1 kW to 1.3 kW side channel blower and 80% of the performance of a 3 kW side channel blower. The wear-free touch control panel of this new insulation layer dryer allows for convenient operation at the touch of a finger. No controls, no wear.   With the help of the new whisper mode, the sound level of the unit can be reduced for 10 hours, yet the device operates as efficiently as usual. "Furthermore, it has an interface for data exchange with the latest generation of our drying unit DA 4 M. The connection of both units enables networking of all device data, including real-time remote monitoring of system status and drying progress." The multifunction display not only clearly shows the current operating status and volumetric flow rate - even in the dark or from a distance - as a plain text display, but additionally, the color of the display lighting automatically indicates how effectively the drying air can flow through the insulation layer in your installation.     Performance-optimized energy consumption through HiDry automation   In contrast to conventional compressor turbines, the VX turbo engines have power and energy consumption always in a direct linear relationship. When the power is reduced, the energy consumption is also reduced. Furthermore, the power control is not resistance-oriented, but is focused on the required volumetric flow rate. Thanks to this technology, VX units operate at a particularly energy-saving eco rate compared to turbine compressors, especially in the drying final phase.     Advantages at a Glance   • Unique adaptive power control - makes thinking in device classes practically unnecessary• Replaces all side channel blowers in the power classes from 0.8 kW to 3 kW• Super lightweight - only 10 kg• 35 % lighter than comparable competitive models• Up to 75% lighter than side channel blowers of the same performance class• DA-4 interface for networking all device data including real-time remote monitoring of system status and drying progress• Optiflow-NT multifunction display with clear text status display and performance control color lighting• Digital counter for operating hours and energy consumption• Whisper mode for very quiet night operation• Wear-free touch control panel • HotStop System• Service socket for dehumidifier (EU socket!)• Cable receiver with lockable plug• Clear text status display• Protection-enhanced control elements• Maintenance quick-release fasteners       scope of delivery   device with • 2x connection fittings for 38 mm hoses • Filter sieve for drying in overpressure process • 2x VX-Microfilter element fine dust filter class F8     Important   • The four-way splitter visible in the product image is not included in the scope of delivery • The blue socket on the device corresponds to a EU socket. Only 2-pole plugs fit Swiss devices.      Technical data   Recommended room size overpressure 90 m² negative pressure 70 m² max. overpressure 270 mbar max. negative pressure 220 mbar Air volume blowing free 250 m³/h Defined volumetric flow rate-  optimum (aspirating)       Stage Whisper Mode: 100 m³/h Level 1: 100 m³/h Level 2: 150 m³/h Level 3: 180 m³/h Level 4: 250 m³/h power connection 230 V / 50 Hz rated current consumption max. 5.5 A Power consumption max. 1200W Cable length approx. 3.5 m Plug EU plug with Swiss adapter Dimensions W x H x D 430 x 415 x 420 mm Weight 10 kg Trotec article no. 1.560.000.042 guarantee 2 years

Learn more More Fewer

A reliable wall-mounted dehumidifier with considerable dehumidification power and an appealing design. A durable, corrosion-protected construction made of powder-coated, galvanized steel sheet ensures maximum reliability for this industrial condensate dryer and makes it particularly resistant to environmental influences thanks to its coated heat exchanger. The combination of high efficiency and low-maintenance design makes the dryer ideally suited for fully automatic, hygrostat-controlled continuous drying applications in numerous fields of use, and thanks to its autonomous recirculation operation, it can also be easily integrated into any application environment afterwards. With its KTL-coated heat exchanger, it is also extremely resistant to environmental influences even in particularly reactive air environments with high salt, chlorine, or solvent content.    Hygrostat controlled and protection against manipulation The built-in hygrostat automatically regulates the humidity to an optimal level, where condensation, mold, or corrosion have no chance. The target humidity can be freely adjusted according to your needs. High efficiency is ensured by the quiet-running AC axial fan and the powerful compression refrigeration system.  The dry air supplied to the room is simultaneously heated for process technology, so that the use of conventional heating and ventilation energy can be reduced.     Thanks to high-quality hot gas automation, the dryer requires only very short defrosting phases. This is optimal, especially for dehumidifying unheated rooms, as it improves the performance and increases efficiency.  The controls are protected against unauthorized access, making this industrial dryer also the ideal dehumidifier for public buildings, staff and changing rooms, or museums.   Wide range of applications In wall operation, the device can be used for a variety of applications, for example:  • Humidity control in staff rooms, changing rooms, lounges, and break rooms• Drying of changing rooms, gyms, bike and ski cellars• Constant humidity conditions in garages, workshops, test benches, or production halls• Dehumidification in archives, collections, or libraries• Dehumidification of water engineering facilities and pumping stations to prevent condensate formation on pipes or pumps• Humidity control during the storage of natural products, for example for quality assurance in wood storage or during the storage of raw tobacco.• Corrosion prevention in electrical switchgear, boiler systems, turbines, and piping systems in power plants or during the storage of raw bodies and metal components.• Humidity control in data centers, control rooms, etc.• Moisture control in the food industry, for example in cheese production or confectionery manufacturing Due to the horizontally directed recirculation airflow and its compact design, the plug-and-play dehumidifier is particularly well suited for installation above door areas.  The condensate drawn from the air is directly drained through a downward laid hose. If the water needs to be drained to higher areas, please also consider our pump kits.  Advantages at a Glance • Professional quality, made in Germany• High dehumidification performance even at low temperatures• Corrosion-protected construction• Fully automatic operation• Professional hot gas defrosting automatic system• Quiet AC axial fan for horizontal recirculation airflow• Optimal suited for installation above door areas• Control elements installed protected from unauthorized access• Available optionally with condensate pump  Technical data  dehumidification performance at 20 °C / 60 % r.H. at 30 °C / 80 % r.H.   20 liters / day 46 liters / day air volume max. 635 m³/ h Maximum room size 130 m² (325 m³) temperature range 5 - 40°C Moisture range technical  Moisture Range Practice 30 - 90 % r.F. 40 - 90 % r.H. (lamella evaporator) Voltage 220 - 240 V/50 Hz rated current consumption max. 4.2 A Power consumption max. 922W Recommended Coverage 16 A Plug approx. 3.5m connection cable with EU plug and Swiss fixed adapter refrigerant R-407C (500g) GWP1774 hose connection   Direct hose connection, no bucket suitable hose 10mm inner diameter short hose piece included in the delivery operating noise   56 dB(A) at 1 m distance 52 dB(A) at a distance of 3 m Masse (B x H x T) 790 x 651 x 255 mm Weight 47 kg defrosting automatic Heissgas dehumidification automation mechanical hygrostat wheel, stepless Ventilator axial, single-stage blower prefilter and operating hour meter no Continuous operation possible and Display no memory function yes (set values remain mechanically fixed) Trotec article no. 1.125.000.116 guarantee 2 years

Learn more More Fewer

This user-friendly set is ideal for precise leak testing and leak detection. Leaky spots are quickly and easily located by blowing in smoke, as the smoke escapes at the leak points and is visually detectable. Thanks to its compact and lightweight aluminum construction, the set is easy to transport and ready for use immediately. The innovative canister holder can be unlocked and unfolded on-site in seconds, thereby increasing the footprint and ensuring high stability even on uneven surfaces such as gravel flat roofs. "For optimal fog generation, both the powerful turbine and the fluid pump can be continuously regulated in their performance and precisely adapted to the respective operating conditions. The intelligent power coupling of the turbine, heating, and pump ensures a consistently dense fog flow for minutes, even at maximum turbine output, without interruptions caused by reheating." The fluid consumption of the FS200 is remarkably low, amounting to a maximum of only 100 ml per minute.Advantages at a Glance• Robust aluminum lightweight construction – therefore more than 40% lighter and smaller than the predecessor model• Extremely powerful blower turbine – infinitely adjustable• Space-saving integral solution with foldable canister holder• Extra dense white smoke thanks to infinitely adjustable fluid pump• Conveniently transportable even through narrow passages such as safety ladders• Intelligent performance coupling of turbine, heating, and pump for consistently dense fog generation for minutes without interruptions due to reheating.• Service-friendly design – easy filter change in seconds• Professional quality "made in Germany" – Original Trotec manufacturing     Technical data   Fog Time at Maximum Level approx. 210 s Fog time at intermediate level and below Persistent fog Evaporator performance 1500 W Turbine power blower 1600 W Maximum power consumption 3100 W Protection class IP54 Air delivery volume approx. 68 l/s (245 m³/h) Fluid consumption at max. output 100 ml/min Fluid consumption in continuous fog 30 ml/min Heating time about 7 minutes Connection voltage 230 V / 50 Hz Dimensions (L x W x H) 270 x 250 x 275 mm Weight (without 5-liter fluid canister) 12.5 kg Trotec article no. 3.510.010.021 Guarantee 2 years     The FS200 includes a 38 mm connection nozzle, a 5-liter canister of branded fog concentrate FluiTect, a filling hose with coupling plugs, and 5 meters of fog hose (Tronect PV-A 38).

Learn more More Fewer

With the professional combination device, you can completely replace a comparable MultiQube tower for drying insulation layers with just one device. This offers 20% more area performance, 50% lighter weight, and 50% space savings! This also makes the transport from the service vehicle to the damage site 100% faster. A multi-device installation with complicated tubing is completely eliminated. Set up, connect, turn on – done! No additional equipment technology is required, as everything is already integrated and ready for connection: a powerful VX-5 turbine insulation layer dryer, a water separator, a 4-stage filter system, and a high-performance silencer – ultra-compactly combined in a robust, stackable aluminum construction that offers you significantly more advantages compared to multi-device solutions while also considerably reducing costs. Your employees will thank you too: 50% less carrying, lifting, hauling, stacking – 100% less tubing, cabling, securing – 20% less assembling.   Worldwide unique integral solution   • VX-5-Turbine• Water separator WA 4i• HEPA filter module• Silencer NR 19 Everything completely installed and ready to connect – lightweight, compact, and powerful – in the world's only integral solution that is both economically and energetically convincing.    Advantages at a Glance • Replaces 4 devices: water separator, HEPA filter, silencer, and all side channel blowers in the power classes from 0.4 kW to 3 kW.• Up to 75% smaller than competitive designs• Up to 20% more area performance than a comparable MultiQube system• 50 % less carry, lift, stack• As quick and easy to install as no other system• Fully automatic always the most effective drying performance thanks to HiDry automation• Optiflow-NT multifunction display with clear text status display and performance control color lighting• Adaptive power control for flexible vacuum surface drying from 10 m² to 85 m²• Digital counter for operating hours and energy consumption• DA-4 interface for real-time remote monitoring of system status and drying progress• Integrated thermal protection to prevent damage to drying equipment, inventory, and building fabric.• Night operation - Whisper mode• Wear-free touch control panel• Additional HEPA filtration cost-effective only when needed• Total weight only 27 kg• High-quality product, made in Germany  Small cause, big effect Thanks to its ultra-compact design, this combination device allows you to achieve up to 100% more work productivity and up to 300% more storage productivity. All "practical time wasters" can be eliminated in one go – thus, you benefit from extreme productivity gains in the daily routine of restorers. Fewer devices to manage and "move" per damage, less storage requirement, more equipment per trip in the service vehicle, faster loading and unloading, quicker transport from the vehicle to the damage site, faster installation, faster dismantling, less cleaning effort. In summary, you can significantly increase your work and storage productivity.  touch control panel Convenient operation at the touch of a finger. No controls, no wear. A light press on the corresponding symbol is enough to configure the operation.In addition to the plus-minus buttons for quick selection of power levels, the control panel also features functions for an extra whisper mode as well as a combined display of power consumption and operating hours.  Optiflow-NT-Multifunction Display The current operating status and volumetric flow are clearly readable on the display, even in the dark or from a distance. Additionally, the color of the display lighting automatically indicates how effectively the drying air can flow through the insulation layer at your installation. Green confirms optimal volumetric flow, orange indicates borderline areas, and with a red LED, the air throughput is insufficient for the area, making optimization necessary for quick drying.  Night operation - Whisper mode In whisper mode, the device operates particularly quietly yet efficiently. To reduce noise levels, the power is not simply reduced; instead, it is regulated with noise-optimized weighting to the volume flow optimum of performance level 2."Once activated, the dryer operates in whisper mode for ten hours and then automatically switches back to the previously used power level. Extremely practical for customers who need a maximum dampened noise level for a short time."  Sensor-supported thermal protection function An integrated sensor system monitors the internal air temperature. It automatically switches from the current setting to level 1 before destructive climate conditions above 45 °C are reached inside the device, which could lead to material stress and thus shorten the device's lifespan. The temperature will continue to be monitored and will automatically switch back to regular operation in the event of falling temperatures. However, if the temperature level remains critical for too long, the device will be completely turned off for its protection.  TTKwic-Modus The device features all the water separator performance characteristics of the WA 4i, including two TTKwic quick couplings for easy drainage connection of dehumidifiers. To ensure that their condensate is reliably pumped out through the TTKwic quick couplings even when switched off, you can set the device to TTKwic mode via the control panel. The motor is off in this mode, but the pump remains active.  Turbo engine with adaptive control of power The four-stage adjustable turbo engine reaches up to 20,000 rpm and guarantees maximum efficiency at every power level, because the integrated HiDry automation continuously measures the current volumetric flow in m³/h and automatically regulates the operation to the optimal air throughput. By pressing a button, a higher power class or, if needed, the extra whisper mode can also be selected.  HiDry-Automatic Fully automatic always the most effective drying performance "Generating motor power beyond the required level does not speed up drying, but it does increase wear and power consumption. The crucial success factor for accelerated drying progress is not the motor power, but a consistently high air flow in the insulation layer zones to be dried." "Therefore, the Qube+ is equipped with the innovative HiDry control automation, which adjusts the performance not based on resistance, but rather oriented towards volumetric flow, and in this way automatically guarantees the most effective performance at every stage for each drying setup." Similar to a "cruise control" in a car, the sensor-supported HiDry automation continuously adjusts the volumetric flow performance of the Qube+ dynamically to the preset optimum of the respective performance level."At the beginning of the drying process, when the resistance is still relatively high, more motor power is required to maintain the volumetric flow rate; however, the power requirement continuously decreases as the drying progresses."The HiDry automatic system ensures throughout the entire drying duration that the turbo motor of the Qube+ never generates more power than is necessary to maintain the optimal volume flow.The result: Fastest possible drying with minimal energy expenditure!  Performance-optimized energy consumption "In contrast to conventional side channel blower turbines, the turbo engine of the Qube+ always has performance and power consumption in a linear direct relationship:""If the power is reduced or the back pressure decreases, the power consumption is also reduced. Furthermore, the power control is not resistance-oriented, but is focused on the required flow rate." Thanks to this technology, the Qube+ operates extremely energy-efficiently compared to side channel blowers, especially in the drying phase, practically at the energy-saving Eco rate. Always as much power as you need: Performance Level 1: Optimal for the economical drying of small areas. At this level, the Qube+ performs as much as a 0.4 kW side channel blower, but consumes 70% less power!Performance level 2: Corresponds to the performance of a 0.8 kW side channel blower.Performance level 3: The Qube+ is approximately 10% stronger than a side channel blower with a power of 1.1 to 1.3 kW.Performance level 4: Corresponds to 160% of the performance of a side channel blower with a power of 1.1 kW to 1.3 kW and 95% of the performance of a 3 kW side channel blower.  Stackable construction with telescopic push handle  At the push of a button, the height-adjustable telescopic push handle can be extended and retracted. This allows the handle height to be adjusted to the user's needs and retracted for space-saving storage.The engine cover is additionally equipped with a carrying handle and a practical cable holder. Furthermore, two stacking recesses ensure a secure stand for stacked devices during transport or in storage.  Service-friendly designedThe Qube+ features an integrated service socket, to which a condenser dryer or a drying control unit can be conveniently and time-savingly connected.In addition, the Qube+ also houses a 50 mm threaded connection for process air discharge. This effectively reduces the critical heating of the room temperature to preserve the value of your drying equipment.  Flexible Filter System"For all applications that require HEPA filtration, the intake sleeve of the G4 filter sleeve can be easily and quickly replaced by the HEPA filter module with combined F8 pre-filter sleeve."Whether filter change or cleaning, the maintenance-friendly design of the Qube+ allows for quick and safe work here. The turbo motor, power connection, and essential electrical components are completely housed in the motor cover, which can be removed in no time thanks to the quick-release technology. "After the removal of the cover, the lower part of the Qube+ is completely free of electricity, as there are no cable connections from the motor cover. This allows you to start cleaning directly without any further safety measures."  DA-4 interface The Qube+ comes standard with an interface for data exchange with our drying control unit DA 4 Qube.The connection of both units enables networking of all device data, including real-time remote monitoring of system status and drying progress.  Included accessories and consumables • Water separator floor filter mat, 1 piece• G4 filter sleeve, 1 piece• F7-Z-Line-Filter for filtering the intake engine cooling air, 1 piece• 50 mm hose connection fitting for process air discharge, 1 piece• Water drainage hose, length 5m, Ø 12mm  Our accessory tip: All-weather soundproof hood (Trotec SKU No.: 6100000070)  • Noise reduction of up to 5 dB(A) and additional modulation of high frequencies in low-frequency ranges perceived as quieter• Easy to clean and waterproof material• Optimal for continuous operation in residential environments• Ideally suited for outdoor installation, for example in flat roof drying.• Quickly installable and accessible through double zipper system• Supply and exhaust openings ensure optimal engine cooling free from heat buildup.• Also for the use of the Qube+ with the attached drying control unit DA 4 Qube (On order - the delivery time for this hoe is usually 7-10 working days)          Information video application Qube+ Information video Cleaning Qube+     Technical data   Under vacuum suitable for areas up to   Level 1: 25 m² Level 2: 50 m² Level 3: 85 m² Max. negative pressure 220 mbar Air volume blowing free max. 250 m³/ Std. Volume flow rate HiDry (suction)   Stage Whisper Mode 90 m³ / hr. Stage 1 90 m³ / hr. Stage 2 140 m³ / hr. Stage 3 160 m³ / hr. Stage Boost Mode 180 m³ / hr. Engine power 0.2 - 1.2 kW Noise level at 3 m distance 48 - 62 dB(A) Voltage 220 - 240 V/50 Hz rated current consumption max. 6.7 A Recommended Coverage 16 A cable + plug 3.5 m + EU plug with Swiss fixed adapter T12 Bucket 10 Liter Masse H x B x T 735 x 500 x 490 mm Weight 25.2 kg Hose connections insulation layer drying 3 x Ø 38 mm TTKwic dehumidifier quick couplings 2 Connection for process air discharge 50mm service socket 1 x EU socket (Swiss plugs only fit 2-pole) electricity meter yes, digital operating hour meter and Control and Monitoring DA-4 interface EfiDry-Moisture Sensor Connection Overflow sensor with automatic shut-off Trotec article no. 1.560.000.055 guarantee 2 years Documents / Downloads   User Manual German

Learn more More Fewer