This cost-effective construction power distributor meets all requirements for a reliable power supply on construction sites. The connection cable, with a cross-section of 5x10 mm² and a length of about 2 meters, is equipped with a robust CEE63 plug. socketsThe plug feeds the distribution box and supplies the following sockets: 2 x Socket T25 400V / IP 54 (red, front)4 x Socket T23 230V / IP 54 (blue, 2 on each side)1 x CEE16A Socket 3P+N+E / 400V / IP44 (red, front) 1 x CEE63A Socket 3P+N+E / 400V / IP44 (red, front)2 x CEE32A Socket 3P+N+E / 400V / IP44 (red, front)Hedging1x FI circuit breaker 63A / 4 / 30mA2x LS Switch 32A / 3P C2x LS Switch 16A / 3P C1x LS 16A / IP C     Important The CEE63A plug of the connection cable only fits into the corresponding socket. It is larger than the usual CEE16 / CEE32 plugs. The 63A plug has a diameter of approximately 6.8cm and a screw ring. Please ensure that the appropriate connection is available before ordering.   Guarantee2 years

Learn more More Fewer

The "TIP Meter 3/16" is an electricity meter for high-power devices such as heating fans or machines with high power consumption. Equipped with a plug and socket, it can be easily hung between the socket and the device, reliably measuring the power consumption. It is available in two variants, with CEE16 or CEE32 plug/socket.Application examples:- construction sites- Marina- outdoor facilities- market stalls- campsites- Nurseries, CBD cultivationetc.   The recorded consumption values are immediately saved and can be retrieved at any time even after a power interruption. The "TIP Meter" is manufactured in Germany and is built to a very high quality. This version is approved for use in Switzerland. It uses the well-known SINUS 85 meter without MID.2 year guarantee   Technical dataRated voltage / frequency: 3 x 400 V / 50 HzMeasuring range: 0.25 - 85 AAccuracy class: 1 (class B) = +-1% toleranceOperating temperature range: -10°C - +45°CProtection class: IP44Application area: Indoor and outdoorHousing dimensions: 18 x 11 x 11.5 cmCable cross-section CEE16 2.5mm²Cable cross-section CEE32 4.0mm²Cable length: 2 x approx. 50cm

Learn more More Fewer

The "TIP Meter 3/16" is an electricity meter for high-power devices such as heating fans or machines with high power consumption. Equipped with a plug and socket, it can be easily hung between the socket and the device, reliably measuring the power consumption. It is available in two variants, with CEE16 or CEE32 plug/socket.Application examples:- construction sites- Marina- outdoor facilities- market stalls- campsites- Nurseries, CBD cultivationetc. The recorded consumption values are immediately saved and can be retrieved at any time even after a power interruption. The "TIP Meter" is manufactured in Germany and is built to a very high quality. This version is approved for use in Switzerland. It uses the well-known SINUS 85 meter without MID.2 year guarantee Technical dataRated voltage / frequency: 3 x 400 V / 50 HzMeasuring range: 0.25 - 85 AAccuracy class: 1 (class B) = +-1% toleranceOperating temperature range: -10°C - +45°CProtection class: IP44Application area: Indoor and outdoorHousing dimensions: 18 x 11 x 11.5 cmCable cross-section CEE16 2.5mm²Cable cross-section CEE32 4.0mm²Cable length: 2 x approx. 50cm 

Learn more More Fewer

Replacement filters for humidifiers (2-pack)Contains two filter cartridges, suitable for the humidifiers from Stadler Form and Stylies. This is the standard version with a hygienic plastic frame. The humidification performance is identical to the version from Stadler Form.Depending on water hardness, the filter should be changed approximately every 2 to 3 months.Antibacterial treatment against bacterial growth in waterHumidifier models:Stadler Form: Oskar little, Oskar, Oskar bigStylies: Orion, Mira, Carina, Libra  Depending on water hardness, the filter should be changed approximately every 2 to 3 months.

Learn more More Fewer

Stylies Taurus Dampfluftbefeuchter: Reindampf für ein gesundes Raumklima Der Stylies Taurus Dampfluftbefeuchter verbindet modernes Design mit bewährter, hygienischer Warmdampftechnik, um Räume bis zu 70 m² schnell und effizient optimal zu befeuchten. Gesundheit durch Reindampf Der Taurus arbeitet nach dem Verdampfer-Prinzip: Wasser wird auf fast 100°C erhitzt. Das Ergebnis ist ein 100% keim- und bakterienfreier Wasserdampf (Reindampf), der sofort im Raum verteilt wird. Diese Technologie garantiert eine Befeuchtung ohne Keime, Bakterien und Mineralien – die ideale Lösung für ein gesundes Raumklima. Perfekt für sensible Gruppen: Allergiker und Asthmatiker Menschen mit Atemwegproblemen Säuglinge und ältere Menschen Intelligente Leistung und Komfort Mit einer maximalen Befeuchtungskapazität von 0.5 Liter/Stunde (entspricht 12 Liter/Tag) sorgt der Taurus rasch für das gewünschte Klima. Präzise Steuerung: Der integrierte Hygrostat überwacht die Luftfeuchtigkeit automatisch. Variabler Output: Zwei Leistungsstufen (Niedrig / Hoch) für flexible Anpassung. Sicherheit: Eine doppelte Abschaltautomatik garantiert einen sorgenfreien Betrieb. Design-Highlight: Die farbwechselnde LED-Beleuchtung setzt moderne Akzente. Leiser Betrieb: Mit nur < 25 dB(A) arbeitet das Gerät extrem leise. Investieren Sie in den Stylies Taurus und geniessen Sie jederzeit die Vorteile eines optimal befeuchteten und gesunden Raumklimas. Technische Daten – Stylies Taurus Stylies Taurus Dampfluftbefeuchter Spezifikationen Geeignet für Raumgrösse Bis 50 m² Befeuchtungskapazität (max.) 0,5 Liter/Stunde (12 Liter/Tag) Befeuchtungs-Technologie Dampfluftbefeuchter (Warmdampf) Wassertank-Kapazität 7 Liter Leistungsaufnahme (max.) 480 Watt Geräuschpegel < 25 dB(A) Steuerung Integrierter Hygrostat Leistungsstufen 2 (Niedrig / Hoch) Abmessungen (B x L x H) 39.7 cm x 23.5 cm x 29.3 cm Gewicht 2,3 kg Besonderheiten Farbwechselnde LED-Beleuchtung, Duftspender-Funktion Garantie 2 Jahre Wichtiger Hinweis zur Pflege: Regelmässig entkalken und gut ausspülen. Bitte verwenden Sie kein Wasser mit Salz-Zusatz!

Learn more More Fewer

From the "Topten" list of the most economical room air dryers: The Dryfix "Swiss" is an excellent dryer for single-family homes with drying rooms up to 15m.² and approx. 40m of clotheslines. It is economical and quieter than room air dryers with comparable drying performance. The elegant, relatively narrow metal housing integrates optimally into the room's appearance. For installation, the support rail is fixed to the wall with two screws, and the dryer can then be easily hung. Rubber buffers prevent the transmission of (very low) vibrations to the wall. The condensate is directed via a hose either directly into a drain or into a bucket placed under the device. The air intake is on the side (right), and the coarse dust filter can be easily pulled out from the front for cleaning.  Drying programs:On the side of the housing is the control. A toggle switch is used to select whether you want the "Drying" mode or "Room Monitoring". A rotary switch can be used to easily adjust the desired residual moisture.Clothes drying: The drying program can be started at the push of a button. The dehumidifier runs until the laundry is dry and then automatically switches off. Room Monitoring: The general room monitoring serves to prevent mold and odors in the basement. The device automatically activates whenever the room humidity exceeds the value set on the dial, with an ideal value for this mode being around 55-60%. Unlike the laundry drying programs, the dryer never completely turns off in this mode, but only pauses as long as the humidity is appropriate. If the humidity rises again, the drying operation will also reactivate.  You can only get the Dryfix Swiss from us! It is exclusively manufactured for our company in a specialized factory in Switzerland.Ambient temperatureTechnically, the "Swiss" tumble dryers can be used down to 5°C. Please note that the drying time for all room air tumble dryers increases significantly the colder the room is. For optimal drying speed, temperatures of 15°C and above are ideal. The declared drying performance was measured at a room temperature of 20°C.  mounting on the wall  The installation is as simple as with all tumble dryers: a mounting rail is anchored to the wall with 2 screws, and the device can then be hung on it. All necessary installation materials such as screws / dowels are included. as well as 1m hose is included in the delivery. Both the support rail and the two buffers supporting the device against the wall at the bottom are rubber insulated to minimize the transmission of vibrations to the wall. Due to the high dehumidification performance, we recommend draining the condensate directly into the drain with the hose if possible. If you wish to use a bucket, please ensure that it has sufficient capacity (min. 8 liters) to avoid overflow during drying. If wall mounting is not possible, you will find suitable chassis in our range to which the dryer can be mounted.   Upon request, we will professionally install the dryer at your home within a radius of up to 120 km (Fr. 210.-), for further distances, price upon request. Calculate distanceImportant:- Sanitary (drainage) or electrical (230V socket) installations are not carried out by us and must be commissioned separately by an appropriate tradesman, unless already in place.- If your wall has internal insulation, we need to know this when placing the order, as the installation will be more complex. The stated installation prices refer to direct wall mounting, meaning directly on brick or concrete walls without insulation. Additional costs for installation on insulated walls will be charged based on effort.   Technical data drying room: up to 15m² Drying performance: 1.73 Kg/h Consumption per kg of laundry: 0.307 kWh Energy efficiency: A1 Tension: 230V / 50Hz Power consumption: 530W Sound pressure level (our measurement): 1.0 m distance 60 dB(A) 2.5 m distance 57 dB(A) Dehumidification capacity: 26 liters/day (30°C / 80% r.H.) air circulation volume: 600m³/h condensate tank: No integrated tank With hose connection, the water directly drained into the drain or into a bucket. Compressor: Rotary compressor Coolant: R410A Dimensions (H/W/D): 55 x 57 x 26 cm (Depth: from wall to front) Weight: 35 Kg    Business closure: Hygrostatrad Ambient temperature: 5°C ~ 30°C Swiss plug: Yes hose connection: Yes Guarantee: 3 years Special features: Made in Switzerland

Learn more More Fewer

From the "Topten" list of the most economical room air dryers: The Dryfix "Swiss" is an excellent dryer for single-family homes with drying rooms up to 15m.² and approx. 40m of clotheslines. It is economical and quieter than room air dryers with comparable drying performance. The elegant, relatively narrow metal housing integrates optimally into the room's appearance. For installation, the support rail is fixed to the wall with two screws, and the dryer can then be easily hung. Rubber buffers prevent the transmission of (very low) vibrations to the wall. The condensate is directed via a hose either directly into a drain or into a bucket placed under the device. The air intake is on the side (right), and the coarse dust filter can be easily pulled out from the front for cleaning.  Drying programs:On the side of the housing is the control. A toggle switch is used to select whether you want the "Drying" mode or "Room Monitoring". A rotary switch can be used to easily adjust the desired residual moisture.Clothes drying: The drying program can be started at the push of a button. The dehumidifier runs until the laundry is dry and then automatically switches off. Room Monitoring: The general room monitoring serves to prevent mold and odors in the basement. The device automatically activates whenever the room humidity exceeds the value set on the dial, with an ideal value for this mode being around 55-60%. Unlike the laundry drying programs, the dryer never completely turns off in this mode, but only pauses as long as the humidity is appropriate. If the humidity rises again, the drying operation will also reactivate.  You can only get the Dryfix Swiss from us! It is exclusively manufactured for our company in a specialized factory in Switzerland.Ambient temperatureTechnically, the "Swiss" tumble dryers can be used down to 5°C. Please note that the drying time for all room air tumble dryers increases significantly the colder the room is. For optimal drying speed, temperatures of 15°C and above are ideal. The declared drying performance was measured at a room temperature of 20°C.  mounting on the wall  The installation is as simple as with all tumble dryers: a mounting rail is anchored to the wall with 2 screws, and the device can then be hung on it. All necessary installation materials such as screws / dowels are included. as well as 1m hose is included in the delivery. Both the support rail and the two buffers supporting the device against the wall at the bottom are rubber insulated to minimize the transmission of vibrations to the wall. Due to the high dehumidification performance, we recommend draining the condensate directly into the drain with the hose if possible. If you wish to use a bucket, please ensure that it has sufficient capacity (min. 8 liters) to avoid overflow during drying. If wall mounting is not possible, you will find suitable chassis in our range to which the dryer can be mounted.   Upon request, we will professionally install the dryer at your home within a radius of up to 120 km (Fr. 210.-), for further distances, price upon request. Calculate distanceImportant:- Sanitary (drainage) or electrical (230V socket) installations are not carried out by us and must be commissioned separately by an appropriate tradesman, unless already in place.- If your wall has internal insulation, we need to know this when placing the order, as the installation will be more complex. The stated installation prices refer to direct wall mounting, meaning directly on brick or concrete walls without insulation. Additional costs for installation on insulated walls will be charged based on effort.   Technical data drying room: up to 15m² Drying performance: 1.73 Kg/h Consumption per kg of laundry: 0.307 kWh Energy efficiency: A1 Tension: 230V / 50Hz Power consumption: 530W Sound pressure level (our measurement): 1.0 m distance 60 dB(A) 2.5 m distance 57 dB(A) Dehumidification capacity: 26 liters/day (30°C / 80% r.H.) air circulation volume: 600m³/h condensate tank: No integrated tank With hose connection, the water directly drained into the drain or into a bucket. Compressor: Rotary compressor Coolant: R410A Dimensions (H/W/D): 55 x 57 x 26 cm (Depth: from wall to front) Weight: 35 Kg    Business closure: Hygrostatrad Ambient temperature: 5°C ~ 30°C Swiss plug: Yes hose connection: Yes Guarantee: 3 years Special features: Made in Switzerland

Learn more More Fewer

"Connecting pieces in various designs for connecting air hoses in construction and water damage drying. While the T-pieces have a right-angle arrangement of the nozzles, the Y-pieces have a narrower angle. Available designs:" T-piece  Ø 38 mm (for PVC flexible extract hose Ø 38 mm with thread)Ø 38 mm (without thread for all hoses Ø 38 mm)Ø 50 mm (for PVC flexible extraction hose Ø 50 mm with thread)Ø 50 mm (without thread for all hoses Ø 50 mm)   Technical dataHose distributor 38mm + 50mm

Learn more More Fewer

"Connecting pieces in various designs for connecting air hoses in construction and water damage drying. While the T-pieces have a right-angle arrangement of the nozzles, the Y-pieces have a narrower angle. Available designs:" T-piece  Ø 38 mm (for PVC flexible extract hose Ø 38 mm with thread)Ø 38 mm (without thread for all hoses Ø 38 mm)Ø 50 mm (for PVC flexible extraction hose Ø 50 mm with thread)Ø 50 mm (without thread for all hoses Ø 50 mm)   Technical dataHose distributor 38mm + 50mm

Learn more More Fewer

"Connecting pieces in various designs for connecting air hoses in construction and water damage drying. While the T-pieces have a right-angle arrangement of the nozzles, the Y-pieces have a narrower angle. Available designs:" T-piece  Ø 38 mm (for PVC flexible extract hose Ø 38 mm with thread)Ø 38 mm (without thread for all hoses Ø 38 mm)Ø 50 mm (for PVC flexible extraction hose Ø 50 mm with thread)Ø 50 mm (without thread for all hoses Ø 50 mm)   Technical dataHose distributor 38mm + 50mm

Learn more More Fewer

"Connecting pieces in various designs for connecting air hoses in construction and water damage drying. While the T-pieces have a right-angle arrangement of the nozzles, the Y-pieces have a narrower angle. Available designs:"T-piece  Ø 38 mm (for PVC flexible extract hose Ø 38 mm with thread)Ø 38 mm (without thread for all hoses Ø 38 mm)Ø 50 mm (for PVC flexible extraction hose Ø 50 mm with thread)Ø 50 mm (without thread for all hoses Ø 50 mm)  Technical dataHose distributor 38mm + 50mm 

Learn more More Fewer

This heater is characterized by its effective and rapid heat output, making it ideal as an additional heater for apartments or for general heating of poorly insulated rooms during the cool season. With a heating power of 2000 watts, it ensures pleasant comfort temperatures in rooms up to 24 m² or 60 m³. Whether in the living room, bedroom, children's room, in the holiday apartment, in the hobby cellar, party room, office, sales room, or conservatory – this heater creates a cozy atmosphere everywhere.     Perfect combination of convection heat and infrared radiation   Unlike many other heating devices or heaters, the heat from this heat wave heater is not only emitted from one direction into the room. Instead, the combination of convection heating and mica infrared heating elements ensures that the heating is felt all around. Furthermore, the heating elements heat up particularly quickly, so that the heat output is noticeable within just a few seconds. It is best to place the device in the middle of the room so that you can benefit from the even and rapid 3D heat distribution. Further down, you will learn more about the operating principle of the heat wave heater.     Thermostat control for high comfort and low energy consumption   With the remote control and the intuitive membrane button control panel, you can quickly and easily select 2 heating levels (1200 watts and 2000 watts). The current room temperature is always displayed on the LCD screen.   You can optimally adjust the heating power to your room temperature thanks to an intelligent temperature control via thermostat. Simply enter your desired target room temperature in the range of 15 °C to 35 °C. The heating will warm the room until the selected temperature is reached and then automatically switch off. As soon as additional heating is required, the operation will automatically restart, ensuring that the room temperature is kept constant. This process is particularly efficient and energy-saving because only as much heating is provided as necessary to ensure a pleasant feeling of warmth.     Quiet and dust-free warmth   This model operates without a fan blower, unlike electric heaters, and therefore does not stir up any dust in the room. This is particularly pleasant not only for allergy sufferers and asthmatics. Additionally, it generates its heat completely silently, making it suitable for use in the bedroom, for example. This way, you can sleep comfortably and restfully even in rooms that have become very cold, such as when you spend the first night in a holiday home that has not been used for a long time.     Timer function – programmable on and off switching   Equally comfortable and energy-saving is the practical 24-hour timer of the comfort heater. If desired, the device can be automatically turned on or off after a set time (1-24 hours). For example, you can set it so that the heater in the bedroom turns off by itself after you have fallen asleep. Or you can preheat the kitchen in the morning so that you can enjoy your coffee in warmth.     Lots of security   "For safe heating operation, the heat wave heater is equipped with an overheating protection that automatically switches off the device when there is a risk of overheating. It is also well protected against accidental tipping, e.g. by pets, careless guests, or rambunctious children, as the integrated tilt switch immediately deactivates the operation in case of an incline."     How do these infrared heaters work?   The 3D heating system of this heater cleverly combines the advantages of a convector and an infrared heater, providing real all-around warmth in no time:    Efficient Mica Heating Technology with Mica Plates: The 3-layer mica heating plates made from natural mica ore generate a pleasant infrared radiant heat in no time, which, unlike conventional heaters, is emitted not only from one direction but simultaneously forwards and backwards. Another advantage of the high-quality mica heating elements is their full-surface and uniform heating. The intense radiant heat is generated over the entire surface, without loss of power and without consuming oxygen. Additionally, warm air also rises from the hot mica heating elements. This creates a gentle airflow that further distributes the heat throughout the entire room. This principle is called convection.   Space-filling warmth based on the principle of the sun: Infrared radiation works according to the natural principle of the sun. It does not heat the air, but rather the surfaces of the objects it encounters. The objects store the heat and gradually release it back into the room, so that the warmth continues to linger even after the infrared heater has been turned off. On the skin, infrared radiation creates the pleasant sensation of natural sun warmth.   Advantages: The soothing warmth takes effect immediately and without any warm-up time throughout the entire room and does not need to be transported by the circulating room air. Together, the infrared radiation and convection heat complement each other to create a three-dimensional all-around heating system. The heat radiated upwards, forwards, and backwards uniformly warms the entire room. For quick comfort warmth throughout the room – even into the farthest corner.     Healthy indoor climate Breathe Healthy with the Stop-DryAir Function: U You no longer have to worry about dry heating air. Unlike conventional heating techniques, where heating inevitably leads to a decrease in room air humidity, the heat wave heating principle keeps the existing air humidity in the room to be heated constant at the same level.   Especially during the cold autumn and winter months, cool temperatures are perceived as uncomfortable by the body. Then, the infrared heat settles on the skin like a soothing heat plaster. The circulation and metabolism are stimulated, which can in turn have a relieving effect on muscle pain and the musculoskeletal system.     Striking black design "The optics also play a big role, after all, the cool black infrared heater often takes center stage in your room. The high-quality workmanship and the robust retro charm of the black metal grid set a striking design accent in your room ambiance."     Rollbar, compact and easy to transport   Thanks to its compact dimensions, integrated smooth-running wheels, and practical handles, the heater can be quickly and easily moved or carried from one room to another. This keeps you flexible, allowing you to use it in the office, in living and commercial spaces, or for example in wellness areas. The integrated cable management ensures order during transport and storage, preventing tripping hazards.     Advantages at a Glance   • Up to 2,000 W heating power for clean, condensation-free, and odorless warmth• 2 heating levels (1200 W / 2000 W)• 3D Surround Heating System: Combination of infrared radiation and convection heat• High-quality mica heating technology with mica plates• Thermostat-controlled automatic operation with target value selection between 15 °C and 35 °C• Automatic temperature control• Current room temperature display• Stop-DryAir: no drying out of the room air• Timer Function• IR remote control• LCD-Display• Energy-efficient operation thanks to automatic shutdown upon target value achievement• Maximum safety thanks to overheating and tilt protection• Easy transport through handles and integrated wheels• Silent heating Please note: The device is only suitable for use in well-insulated rooms or for occasional use.     Technical data   Heating output 1200W / 2000W Heizart Convection and Infrared Heat Waves Maximum room size 24 m² (60 m³) Temperature range 15 - 35 °C voltage 220 - 240 V/50 Hz Nominal current consumption max. 8.7 A Power consumption max. 2000W Recommended Coverage 10 A Cable length approx. 1.2 m Plug EU plug with Swiss adapter Dimensions W x H x D 640 x 660 x 260 mm (including stand feet) Weight 5 kg Protection class IPX0 On/off switch yes, plus step switch 1200W - 2000W Thermostat control and LC-Display and Frost Watch Function no Automatic shutdown at target value and Parental controls no Timer yes (1-24 hours) Memory function yes (values are saved, operation on timer possible) Anti-tip protection and Overheating protection and Guarantee 2 years

Learn more More Fewer