Marker dye for building diagnostics and leak detection.Water-soluble powder for• the tracing and leak detection in drains and wastewater systems• the detection of leaks in flat roofs, terrace drains, and underground garages  "It is harmless to humans and animals as well as biologically unproblematic." standard colors The leak detection dyes are available in red, green, blue, and yellow. They are visually recognizable without aids. These are dissolved in water in the area to be tested, making the water flow to be examined visible.special paintAdditionally, the leak detection dye is available in fluorescent/uranine. It is most visible under infrared and ultraviolet light.ApplicationThe marking dye is dissolved in water (1 level teaspoon of dye for 10 liters of water). A lower or higher color intensity can be individually adjusted by using more or less dye. Please refer to the safety data sheet and adhere to the recommended dosage.   questions and answersAre the leak detection dyes also suitable for murky water? Yes. Generally, leak detection involves wastewater or contaminated water. The application is possible with all colors and also with fluorescein. However, for fluorescein, you will additionally need a UV flashlight. Please refer to the safety data sheet and always discuss the applications with the respective environmental authority. Applications involving drinking water or groundwater discharge could be problematic. "We need to check an underground river course. Are your colors approved for this?" Yes. Our colors are very well suited and approved for leak detection in wastewater. However, please contact the relevant environmental authority before use, as it may be possible that you could color a body of water, and then, of course, calls from concerned citizens would arrive at the office. Present our corresponding safety data sheet for this purpose. Please observe the safety data sheet and always discuss the applications with the respective environmental authority. Applications involving drinking or groundwater discharge could be problematic.Can your colors be used for flat roof leak detection?Yes. You would need to subdivide the roof area, seal the drains, and partially flood sections by adding colors. This way, you can localize the leak. Also, try this with our test fog, which you can push under the roof membrane using a fogger and a side channel blower. If you detect fog escaping here, you have pinpointed the error accurately. Please refer to the safety data sheet and always discuss the applications with the respective environmental authority. Applications involving drinking or groundwater introduction could be problematic.

Learn more More Fewer

Immediate evaluation on site. Conventional mold tests have the disadvantage that evaluation takes a long time. In contrast, with the "Test-it", it can be determined immediately on-site not only whether a substance is infested with mold, but also whether it is the dangerous "Aspergillus".Especially the two species "Aspergillus fumigatus" and "Aspergillus brasiliensis" are often found on good nutrient substrates such as wallpaper, wood, or paper. These can be very toxic under certain circumstances. A thorough treatment is strongly recommended.Application of the analysisWith Test No. 1, you can determine within 2 minutes whether the material on a surface is biologically active. If so, you are dealing with mold, yeasts, or bacteria. This means the surface is not hygienically flawless. Disinfection is advisable in any case."Use Test No. 2 if Test No. 1 has shown a positive result. You can now easily and quickly analyze whether the material consists of fungi of the genus 'Aspergillus spp.'""If test No. 2 shows a positive result, it is quite possible that the fungus is an Aspergillus fumigatus or an Aspergillus brasiliensis (formerly known as 'niger'). These two species are potentially pathogenic, meaning they can, for example, trigger allergies."In this case, it is appropriate to have the infestation removed by a professional.A lab test is not necessary in most cases. However, if immunocompromised individuals are involved, it makes sense to conduct this test nonetheless. A doctor can possibly optimize therapies with the available results.     The test substances are heat-sensitive, so it is advisable to purchase a suitable cooler.   Scope of delivery:• 5 x 3M Clean Trace Test for the determination of biologically active material• 1 x cardboard holder as a stand for 3M Cleant Trace• 5 x Aspergillus test strips• 5 x reaction fluid for Aspergillus test• 5 x swabs for sampling mold• 1 x imprint test for the detection of mold and bacteria• 1 x Instruction manual with explanations for the mold test (German)   Shipping costs for 1 item: Fr. 12.- (Based on B-Post, further shipping options can be viewed in the shopping cart).

Learn more More Fewer

Polyurethane (PUR) extension cable with plug and socket380/400V 32A 5x4mm² (suitable for e.g. heating fans up to max. 18 kW): Acid-resistant* extension cables made of polyurethane (PUR) with orange sheathing. The inner conductors are made of rubber-silicone for high flexibility. Suitable for use on construction sites, in industry and commerce for operating power-intensive devices such as fan heaters, construction machinery, etc. Includes coupling and plug. For high mechanical stress in dry to wet rooms and outdoors (the plug and socket must be kept dry). Lower wear under abrasion and grinding stress compared to conventional plastic or rubber sheaths. Plug contacts stainless steel nickel-plated, IP-44 splash-proof.*Polyurethane is resistant to, among other things, these acids:Ammonia, ASTM Oil Cat. I - III, ASTM Fuel No. I, Diethyl ether, Diethylene glycol, Glycerin, Glycol, Potassium hydroxide, Kerosene, Sodium hypochlorite solution, Sodium hydroxide max. 10%, Olive oil, Ozone, Paraffin (oil), Petroleum ether, Vegetable oils / fats, Sulfuric acid max. 30%, Silver salts max. 10%, Hydrogen peroxide max. 9%(Partial stability with other acids depending on type and concentration. All information is based on our experience and without guarantee, please ensure to consult a specialized chemist when using in the presence of acids in any case.) "Available on request with thicker cross-section 380/400V 32A 5x6mm² within 4 days (surcharge for 5x4mm²: +50%)."  Technical data Cable: H07BQ-F 5 x 4.0 mm² with rubber insulated conductorsCoat: PolyurethaneCEE plug: 32A 5p 6h 400VCEE plug: 32A 5p 6h 400VLengths: 10m, 15m, 20m, 25m, 30m, 50m (any other lengths available on request)Warranty: 2 years Standards:DIN VDE 0282-10HD 22.10 S1+A1DIN VDE 0295 Class 5 (Conductor Construction)HD 308 S2 (Recognition Mark)EN 60332-1-2 (Flame Behavior)  

Learn more More Fewer

Cable reel 400V IP44 with abrasion and acid-resistant* PUR cable, for up to 10800WApproved for commercial use on construction sites. With CEE16 plug, protected IP44.2 side sockets 2xCEE16/5+1xT25/5 for connecting devices.Available cable lengths: 20m (25m + 30m available on request / delivery time approx. 5 days)*Polyurethane (PUR) is resistant to, among other things, these acids:Ammonia, ASTM Oil Cat. I - III, ASTM Fuel No. I, Diethyl ether, Diethylene glycol, Glycerin, Glycol, Potassium hydroxide, Kerosene, Sodium hypochlorite solution, Sodium hydroxide max. 10%, Olive oil, Ozone, Paraffin (oil), Petroleum ether, Vegetable oils / fats, Sulfuric acid max. 30%, Silver salts max. 10%, Hydrogen peroxide max. 9%(Partial stability with other acids depending on type and concentration. All information is based on our experience and without guarantee, please ensure to consult a specialized chemist when using in the presence of acids in any case.)Always fully unwind the cable reel when in use.   2 year guarantee   Shipping costs for 1 item: Fr. 12.- (Based on B-Post, further shipping options can be viewed in the shopping cart)   Technical data Cable lengths: 20 / 25 / 30 meters Cable cross-section: 5 x 2.5 mm²Cable mat: PUR (abrasion and acid resistant)Roll: Plastic, black, with steel tube frame and handleOverheating protection: yesWarranty: 2 years

Learn more More Fewer

Immediate evaluation on site. Conventional mold tests have the disadvantage that evaluation takes a long time. In contrast, with the "Test-it", it can be determined immediately on-site not only whether a substance is infested with mold, but also whether it is the dangerous "Aspergillus".Especially the two species "Aspergillus fumigatus" and "Aspergillus brasiliensis" are often found on good nutrient substrates such as wallpaper, wood, or paper. These can be very toxic under certain circumstances. A thorough treatment is strongly recommended.Application of the analysisWith Test No. 1, you can determine within 2 minutes whether the material on a surface is biologically active. If so, you are dealing with mold, yeasts, or bacteria. This means the surface is not hygienically flawless. Disinfection is advisable in any case."Use Test No. 2 if Test No. 1 has shown a positive result. You can now easily and quickly analyze whether the material consists of fungi of the genus 'Aspergillus spp.'""If test No. 2 shows a positive result, it is quite possible that the fungus is an Aspergillus fumigatus or an Aspergillus brasiliensis (formerly known as 'niger'). These two species are potentially pathogenic, meaning they can, for example, trigger allergies."In this case, it is appropriate to have the infestation removed by a professional.A lab test is not necessary in most cases. However, if immunocompromised individuals are involved, it makes sense to conduct this test nonetheless. A doctor can possibly optimize therapies with the available results.     Since the test substances are heat-sensitive, this set already includes a suitable cooling box for transport. It is equipped with a power adapter as well as a 12V connection for transport in the car. Scope of delivery:• 1 x cooler box including power supply and 12V charging cable• 5 x 3M Clean Trace Test for the determination of biologically active material• 1 x cardboard holder as a stand for 3M Cleant Trace• 5 x Aspergillus test strips• 5 x reaction fluid for Aspergillus test• 5 x swabs for sampling mold• 1 x imprint test for the detection of mold and bacteria• 1 x User manual cooler box (multilingual including German)• 1 x Instruction manual with explanations for the mold test (German) Shipping costs for 1 item: Fr. 12.- (Based on B-Post, further shipping options can be viewed in the shopping cart). Technical dataCooler: Dimensions L x H x W 32 x 28 x 19 cmCapacity 7 litersPower connection 12V or 230V with power supplyConsumption 38W (12V) or 43W (230V)Cooling capacity approx. 25°C below ambient temperatureWeight 2.8 Kg (empty and without adapter)

Learn more More Fewer

The LB50 belongs to the so-called cold water evaporators and is suitable for humidifying large spaces.The air is first cleaned by a 3M carbon filter and then passed through the humidifying evaporation mat of the humidifier. The water evaporates naturally, ensuring a consistent humidity level in the room.The evaporation capacity of the humidifier is a maximum of 1.9 liters of water per hour and is sufficient to humidify rooms up to 180 m2 / 450 m3. The addition of a silver stick ("Ionic Silver Stick" or "Clean Cube") to the cold water tank is highly recommended for operation, as it makes the humidification process very hygienic.Good humidity:the relative humidity should average between 40% and 60%. This prevents the drying out of the skin and mucous membranes and improves overall well-being. The moisture prevents cracks in wooden furniture and parquet floors and counteracts the tuning of musical instruments.The humidifier is equipped with a hygrostat and the water tank has a capacity of approximately 10 liters. The Sanvia LB50 humidifier evaporates the following amount of moisture with the different ventilation settings:Stage 1 0.9 liters / hourStage 2 1.3 liters / hourStage 3 1.9 Liters / Hour The Sanvia LB50 humidifier is easy to clean and has an easy-to-fill water tank. A good humidifier with a large humidification capacity, suitable for any environment.2 year guaranteeShipping costs for 1 item: from Fr. 16.- (Basic courier, further shipping options can be viewed in the shopping cart) Technical data Voltage: 230V/50HzPower consumption: max. 170WOperating noise: Level 1: 45 dB(A) / Level 3: 56 dB(A)Recirculation: 180 - 320 m3/hMoistening: max. 45.6 L/24 hrs.Room size max.: 180 m2Control: mechanicalWeight: 19 kgMass B x H x T): 50 x 60 x 35 cmWarranty: 2 years

Learn more More Fewer