A compact dehumidifier with adsorption technology. Adsorption is useful where the room air is cold, or where very low humidity levels are to be achieved. The "DS3" is also ideal for quick laundry drying in cool basements..In contrast to condensation dehumidifiers (dehumidifiers with a compressor), dehumidifiers with adsorption technology have an almost constant dehumidification performance even at low temperatures. They require virtually no lead time from startup until effective dehumidification begins. Due to their compressor-free design, these dryers are lightweight at only 7.5 kg. Technologically, the device would even extract water from the air below freezing point; however, the water then freezes in the collection tray, making 0.5°C the limit for use. Even at warmer temperatures, drying with adsorption dryers is straightforward, but the power consumption per liter of water extracted in temperate rooms is higher than that of compressor dehumidifiers (condensation dehumidifiers). The crossover point is around 8-10°C, meaning that below this value, adsorption dryers are more efficient, while above it, condensation dryers are more effective.Once the target humidity is reached, the dehumidification operation stops, while the ventilation continues for a few more minutes until the device has cooled down sufficiently. Subsequently, dehumidification and ventilation pause until the humidity in the room rises above the desired target humidity level again. The ventilation is powerful and can be adjusted in 3 stages. This is particularly advantageous when drying laundry and significantly speeds up the process. With the vertically adjustable air outlet louver, the dry air can also be directed in the desired direction. The wind noise is audible even at the lowest setting, so the DS3 is only partially suitable for very quiet bedrooms.Special function air purification with HEPA filterThe DS3 can also be used as an air purifier. A suitable HEPA filter available from us can be placed in the air intake area. This filters the air with a purity rate of over 99.9% and removes all airborne particles such as pollen, fine dust, spores, viruses, and germs from the air. The air purification mode can run together with the dehumidification operation, but also without dehumidification thanks to the pure air circulation level. The filter can be ordered individually.  Characteristics of the DS3• Dehumidification capacity of up to 9.5 liters per day.• Adsorption technology without a compressor and without refrigerants.• already at cool 0.5°C a good dehumidification performance.• significantly larger water bucket (5 liters) than comparable devices, auto-stop when full tank including warning light.• Electric hygrostat (LED) for regulating and setting the desired humidity.• Humidity control in 10% steps from approx. 40% to 70% as well as continuous operation possible.• In addition to the standard mode, there are the following operating modes: Auto mode; Dry mode (Turbo) and Air purification mode* (additional *HEPA filter required).• Timer function to select the automatic remaining time or the start time between 1-24 hours.• Clear display including current humidity display and status overview.• Also suitable for continuous operation/continuous dehumidification.• SmartHome capable (via WLAN socket) + can be controlled via external timer switch (only possible with a few devices).• Memory function: no adjustments during power failure (device continues from where it was interrupted).• Possibility for direct hose connection for draining water into a lower outlet (suitable hose: 12mm inner diameter).• Absolutely maintenance-free.• Washable, antibacterial air filter.• Modern design and appealing appearance, therefore also very suitable for living spaces.• The device is immediately ready for use (no installation or assembly required).• Comparatively light in weight, easy mobility with side grip recesses.• Fulfillment of the WEEE standards.• TÜV "GS" tested as well as CE and EMC conformity.   scope of deliveryThe delivery includes the ready-to-plug-in device as well as an activated carbon net, which can be placed in the air intake area and slightly improves the air quality during operation. The HEPA filter is optional and is not included in the basic delivery.  application examples   • Drying of poorly insulated basements, garages, boats, caravans during the winter season • Laundry drying in cold laundry rooms • Drying of herbs and spices       Technical data   Tension 230V / 50Hz Power consumption max. 730W Sound pressure level (our measurement) Weakest fan stage: 1m distance 48 dB(A) 2.5m distance 44 dB(A) Strongest fan speed: 1m distance 55 dB(A) / ideal for laundry drying 2.5m distance 52 dB(A) fan         Weakest fan stage air volume approx. 170 m³/h Blow-out speed approx. 4.4 m/s. Strongest fan stage air volume approx. 270 m³/h Blow-out speed approx. 6.5 m/s. dehumidification performance   max. 9.5 liters per day (at 30°C / 80% r.H.) max. 9 liters per day at 8°C / 80% r.H.) condensate tank Approx. 5 liters and direct hose connection (12mm) refrigerant not available/adsorption technology Dimensions (H/W/D)   515 x 360 x 240 cm   Weight 7.5 Kg Ambient temperature 1°C ~ 32°C  Comparable devices EcoQ 9L Steady Area of application bus ca. 50 m² Swiss plug Yes   guarantee 2 years Documents/Downloads   User Manual German

Learn more More Fewer

This maintenance-friendly adsorption dehumidifier guarantees high dehumidification values. With its standard stainless steel housing and an electrical control box in IP53 design, it is also corrosion-resistant and withstands adverse operating environments. "It is ideally suited for many drying tasks or dry air production. Typical applications include drying in the chemical, pharmaceutical, and food industries, as well as in mechanical engineering. Furthermore, it is also used to protect machines, inventory, and buildings from corrosion, condensate, or mold formation, for example in water engineering facilities or electrical control centers."   High dry air performance even at low dew point The TTR series adsorption dehumidifiers take advantage of the vapor pressure difference between the humid air and a hygroscopic sorbent material, which is incorporated into a drying wheel that has an extremely large surface structure. This process ensures high dehumidification performance even at low humidity and low air temperatures.   TTR-Trisorp-Dual-Principle    Two separate air ducts lead process and regeneration air through each fan. The process air to be dehumidified is drawn in with the help of a fan and flows through the dehumidification sector of the continuously rotating drying wheel, where the moisture contained in it is removed by binding in the sorbent. From there, it flows out as dry air.    When flowing through the heating register, the air is heated significantly and can thus reduce its moisture. Subsequently, it passes through the regeneration sector, where it can reabsorb the moisture bound in the silica gel and discharge it outside through the moist air outlet.     Series-integrated heat recovery (HR)   A major advantage of the TTR adsorption dryers is the already integrated heat recovery system as standard. Depending on the ambient conditions, this saves 20 - 50% energy. Thus, the savings at 20° C and 60% relative humidity (i.e., under "normal" room conditions) is about 50%. In principle, the regeneration air is also drawn in with a separate fan and passed through the purge sector. As the drying wheel heats up due to the released adsorption heat and the regeneration heat, the purge sector serves for heat recovery and cooling of the drying wheel. This reduces the required energy input and improves the dehumidification performance, especially at lower dew points.   Wide range of applications Due to its very high dehumidification performance in continuous operation even at low dew points, this dehumidifier is suitable for a variety of applications, for example: • Pre-dehumidification of supply air to maintain the trickling and flowability of hygroscopic products in storage, conveying, and dosing systems.• Process air dehumidification for gas turbines and humidity control in gas distribution stations• Ice-free maintenance of freezing tunnels and deep-freeze storage• Dehumidification or process air drying in the fields of the chemical and pharmaceutical industry, electronics and semiconductor industry, or food industry• Avoidance of condensation formation, material changes, or granulate clumping in plastic processing• Process air drying and plant dehumidification in the steel industry• Air drying and dew point control in cold storage rooms• Drying of water engineering facilities and pumping stations• Climate conditioning of ammunition depots or military technical equipment storage facilities• Dehumidification and dew point control in clean and dry rooms• Climate conditioning in dry air storage or in timber storage halls  Value added without extra cost The dryer is already equipped as standard with numerous functions and features that guarantee reliable operation, easy handling, and long service life with low maintenance effort: • Wide voltage• Rotor speed control (rotor and drive)• Overtemperature safety system with restart lock (regeneration air)• Operating temperature management (regeneration air)• Filter monitoring (per air flow and collective warning light)• Configurable air direction reversal (conversion with minimal effort)• Terminals for external ON/OFF• Potential-free contacts (operation, fault, filter)• Operating hour meter• Air volume regulation• integrated heat recovery• Robust and maintenance-friendly stainless steel housing• Duoventic control* for regeneration air and process air fan respectively• Overtemperature safety system with restart lock (regeneration air)• G4 air filter in Z-line design with electronic monitoring and collective warning light• External connection terminals On/Off and connection terminals Hygrostat  Possible additional options • Tax module Millennium• Flowmatic-Flow Rate Control• Humidity/Temperature Control• Dew point sensor -80 °C ... +20 °C• Touch screen for device operation• Remote connection GSM• Remote connection WLAN• Heat exchanger module• Electric reheater for dry air• External Hygrostat HG 120• External Hygrostat HG 125• Transport frame (stackable), with wheels  Advantages at a Glance  • High dehumidification performance even at low dew points• Robust stainless steel housing• Reliable silica gel adsorption rotor• Configurable air direction reversal (conversion with minimal effort)• Duoventic control – the performance of each fan can be individually adjusted using a potentiometer.• TTR-Trisorp-Dual-Principle with separate guidance of process and regeneration air for a pressure-neutral recirculation operation• Electric regeneration heating• Filter monitoring (per air flow and collective warning light)• Individually configurable through a variety of equipment options for almost every application.*According to Duoventic, the performance for each fan can be independently adjusted via a potentiometer; no throttling devices are required on-site.  A notice: This device is available under the brands "Trotec" and "Dantherm". Technical data  dry air Dehumidification at 20°C/60% r.H. 3.6 kg/hour = 86.4 kg/day Air volume blowing free 950 m³/h nominal air volume 750 m³/h external pressing 300 Pa connection inlet Ø 250 mm connection outlet Ø 250 mm     regeneration air nominal air volume 130 m³/h external pressing 300 Pa connection inlet Ø 160 mm connection outlet Ø 160 mm     working principle TTR-Trisorp-Dual Ambient temperature -20 to +40 °C Ambient humidity (non-condensing) 0 - 100 % r.F. power connection 380 - 480 V/50 - 60 Hz rated current consumption 7.5 A Installed capacity 4.9 kW heating capacity 4.1 kW recommended coverage 16A electrical connection terminal connection Suitable for continuous operation and Dimensions H x W x D 942 x 649 x 734 mm Weight 85 kg Country of production Germany Trotec article no. 1.110.000.150 guarantee 2 years

Learn more More Fewer